Enhanced Microchannel Heat Sinks Using Oblique Fins

2009 ◽  
Author(s):  
Yong-Jiun Lee ◽  
Poh-Seng Lee ◽  
Siaw-Kiang Chou
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Secondary Flows ◽  
Heat Sinks ◽  
Microchannel Heat Sink ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

Oblique fins created in a microchannel heat sink can serve to modulate the flow, resulting in local and global heat transfer enhancement. Numerical analysis of laminar flow and heat transfer in such modified microchannel heat sink showed that significant enhancement of heat transfer can be achieved with negligible pressure drop penalty. The breakage of continuous fin into oblique sections causes the thermal boundary layers to be re-initialized at the leading edge of each oblique fin and reduces the boundary-layer thickness. This regeneration of the entrance effect causes the flow to be always in a developing state thus resulting in better heat transfer. In addition, the presence of the smaller oblique channels causes a fraction of the flow to branch into the adjacent main channels. The secondary flows thus created improve fluid mixing which serves to further enhance the heat transfer. The combination of the entrance and secondary flow effect results in a much improved heat transfer performance (the average and local heat transfer coefficients are enhanced by as much as 80%). Both the maximum wall temperature and temperature gradient are substantially decreased as a result.

Heat Transfer Enhancement in Triangular Ducts With an Array of Side-Entry Wall/Impinged Jets

1999 ◽  
Author(s):  
J.-J. Hwang ◽  
C.-S. Cheng ◽  
Y.-P. Tsia
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Enhancement ◽  
Transfer Coefficients ◽  
Pressure Drops ◽  
Heat Transfer Coefficients ◽  
Inclined Angle

An experimental study has been performed to measure local heat transfer coefficients and static well pressure drops in leading-edge triangular ducts cooled by wall/impinged jets. Coolant provided by an array of equally spaced wall jets is aimed at the leading-edge apex and exits from the radial outlet. Detailed heat transfer coefficients are measured for the two walls forming the apex using transient liquid crystal technique. Secondary-flow structures are visualized to realize the mechanism of heat transfer enhancement by wall/impinged jets. Three right-triangular ducts of the same altitude and different apex angles of β = 30 deg (Duct A), 45 deg (Duct B) and 60 deg (Duct C) are tested for various jet Reynolds numbers (3000≦Rej≦12600) and jet spacings (s/d = 3.0 and 6.0). Results show that an increase in Rej increases the heat transfer on both walls. Local heat transfer on both walls gradually decreases downstream due to the crossflow effect. At the same Rej, the Duct C has the highest wall-averaged heat transfer because of the highest jet center velocity as well as the smallest jet inclined angle. Moreover, the distribution of static pressure drop based on the local through flow rate in the present triangular duct is similar to that that of developing straight pipe flows. Average jet Nusselt numbers on the both walls have been correlated with jet Reynolds number for three different duct shapes.

Experimental Investigation of Silicon-Based Oblique Finned Microchannel Heat Sinks

2010 ◽  
Author(s):  
Yong-Jiun Lee ◽  
Poh-Seng Lee ◽  
Siaw-Kiang Chou
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Heat Sink ◽  
Leading Edge ◽  
Secondary Flows ◽  
Heat Sinks ◽  
Fluid Mixing ◽  
Working Fluid ◽  
Microchannel Heat Sink ◽  
Silicon Based

Sectional oblique fins are employed in contrast to the continuous fins in order to modulate the flow in microchannel heat sink. Experimental investigation of silicon based oblique finned microchannel heat sink demonstrated a highly augmented and uniform heat transfer performance against the conventional microchannel. The breakage of continuous fin into oblique sections leads to the re-initialization of the thermal boundary layers at the leading edge of each oblique fin, effectively reducing the boundary-layer thickness. This regeneration of the entrance effect causes the flow to be always in a developing state thus resulting in better heat transfer. In addition, the presence of smaller oblique channels diverts a fraction of the flow into the adjacent main channels. The secondary flows thus created improve fluid mixing which serves to further enhance the heat transfer. The average Nusselt number, Nuave, for the silicon microchannel heat sink which uses water as the working fluid can increase as much as 55%, from 8.8 to 13.6. Besides, the augmented convective heat transfer leads to reduction in both maximum chip temperature and its temperature gradient, by 8.6°C and 47% respectively. Interestingly, there is only little or negligible pressure drop penalty associated with this novel heat transfer enhancement scheme in contrast to conventional enhancement techniques.

Heat Transfer to an Airfoil in Oscillating Flow

1971 ◽  
Vol 93 (4) ◽  
pp. 461-468 ◽  
Author(s):  
J. A. Miller ◽  
P. F. Pucci
Keyword(s):  
Heat Transfer ◽  
Oscillation Frequency ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Oscillating Flow ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Consequent Increase

Local heat transfer coefficients to an airfoil in an oscillating stream have been measured for a range of frequencies and oscillation amplitudes. Results at moderate angles of attack are in agreement with previously reported findings. However, at large angles of attack, including those associated with stall in steady flow, a strong periodic starting vortex shed from the leading edge leads to a dramatic reattachment of the flow and consequent increase in local Nusselt Numbers of as much as five-fold. These effects are shown to be amplified by increasing oscillation frequency and amplitude.

Influence of High Mainstream Turbulence on Leading Edge Heat Transfer

1991 ◽  
Vol 113 (4) ◽  
pp. 843-850 ◽  
Author(s):  
A. B. Mehendale ◽  
J. C. Han ◽  
S. Ou
Keyword(s):  
Heat Transfer ◽  
Turbulence Intensity ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Reynolds Numbers ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Turbulence Decay ◽  
High Turbulence

The influence of high mainstream turbulence on leading edge heat transfer was studied. High mainstream turbulence was produced by a bar grid (Tu = 3.3–5.1 percent), passive grid (Tu = 7.6–9.7 percent), and jet grid (Tu = 12.9–15.2 percent). Experiments were performed using a blunt body with a semicylinder leading edge and flat sidewalls. The mainstream Reynolds numbers based on leading edge diameter were 25,000, 40,000, and 100,000. Spanwise and streamwise distributions of local heat transfer coefficients on the leading edge and flat sidewall were obtained. The results indicate that the leading edge heat transfer increases significantly with increasing mainstream turbulence intensity, but the effect diminishes at the end of the flat sidewall because of turbulence decay. Stagnation point heat transfer results for high turbulence intensity flows agree with the Lowery and Vachon correlation, but the overall heat transfer results for the leading edge quarter-cylinder region are higher than their overall correlation for the entire circular cylinder region. High mainstream turbulence tends not to shift the location of the separation-reattachment region. The reattachment heat transfer results are about the same regardless of mainstream turbulence levels and are much higher than the turbulent flat plate correlation.

A Detailed Experimental Investigation of a Perforated Heat Transfer Surface Applied to Gas Turbine Recuperators

2003 ◽  
Author(s):  
Juan C. Adams ◽  
Peter T. Ireland ◽  
Martin Cerza ◽  
James Oswald
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Enhancement ◽  
Transfer Coefficients ◽  
Compact Heat Exchangers ◽  
Heat Transfer Coefficients ◽  
Extended Surfaces

An effort is made to explain and improve the understanding of the mechanisms behind the thermo-hydraulic performance of perforated extended surfaces used in compact heat exchangers in the laminar flow regime (ReD = 400–2500). A transient liquid crystal technique, which uses Helium as operating fluid, together with digital image photographic processing have been used to provide measurements of local heat transfer coefficients for this geometry. This work has found that through the use of perforated surfaces there exists a local heat transfer enhancement benefit. It has also been found that although perforations cause a partial restart of the thermal boundary layer, a significant overall surface heat transfer enhancement may not be achieved over plain surfaces. It was also found that the distance between the fin’s leading edge and the point of last significant enhancement resulting from a perforation, linearly depends on Reynolds number. Local heat transfer coefficient measurements were validated by single blow experimentation of similar geometries. The transient single blow technique used the curve-matching method to compare predicted and experimental temperatures.

Effect of Outflow Orientation on Heat Transfer and Pressure Drop in a Triangular Duct With an Array of Tangential Jets

2000 ◽  
Vol 122 (4) ◽  
pp. 669-678 ◽  
Author(s):  
J.-J. Hwang ◽  
B.-Y. Chang
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Leading Edge ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Loss Coefficient ◽  
Heat Transfer Characteristics ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Transfer Characteristics

Experiments are conducted to study the heat transfer and pressure drop characteristics in a triangular duct cooled by an array of tangential jets, simulating the leading-edge cooling circuit of a turbine blade. Coolant ejected from a high-pressure plenum through an array of orifices is aimed at the leading-edge apex and exits from the radial outlets. Three different outflow orientations, namely coincident with the entry flow, opposed to the entry flow, and both, are tested for various Reynolds numbers 12600⩽Re⩽42000. A transient liquid crystal technique is used to measure the detailed heat transfer coefficients on two walls forming the leading-edge apex. Flow rate across each jet hole and the crossflow development, which are closely related to the local heat transfer characteristics, are also measured. Results show that increasing Re increases the heat transfer on both walls. The outflow orientation affects significantly the local heat transfer characteristics through influencing the jet flow together with the crossflow in the triangular duct. The triangular duct with two openings is recommended since it has the highest wall-averaged heat transfer and the moderate loss coefficient among the three outflow orientations investigated. Correlations for wall-averaged Nusselt number and loss coefficient in the triangular duct have been developed by considering the Reynolds number for three different outflow orientations. [S0022-1481(00)01204-4]

Hot Spot Mitigating With Oblique Finned Microchannel Heat Sink

2010 ◽  
Author(s):  
Yong-Jiun Lee ◽  
Poh-Seng Lee ◽  
Siaw-Kiang Chou
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Sink ◽  
Hot Spot ◽  
Local Heat Transfer ◽  
Local Heat ◽  
High Heat ◽  
Secondary Flows ◽  
High Heat Flux ◽  
Microchannel Heat Sink

Sectional oblique fins are employed in contrast to continuous fins in order to modulate the flow in microchannel heat sink. The breakage of continuous fin into oblique sections leads to re-initialization of boundary layers and generation of secondary flows which significantly enhance the cooling performance of the heat sink. In addition, oblique finned microchannel heat sink has the flexibility to tailor local heat transfer performance by varying its oblique fin pitch. Clusters of oblique fins at higher density can be created in order to promote greater degree of boundary layers redevelopment and secondary flows generation to provide more effective cooling at the high heat flux region. Thus the varying of oblique fin pitch can be exploited for hot spots mitigation. Simulation studies of silicon chip with hot spot shows more than 100% increment in local heat transfer coefficient at the high heat flux region for the variable pitch oblique finned microchannel compared with the conventional microchannel heat sink. Both the maximum temperature and its temperature gradient are reduced by 12.4°C as a result. Interestingly, there is only little or negligible pressure drop penalty associated with this novel heat transfer enhancement scheme in contrast to conventional enhancement techniques.

The Effect of Regulating Elements on Convective Heat Transfer along Shaped Heat Exchange Surfaces

2013 ◽  
Vol 34 (1) ◽  
pp. 5-16 ◽  
Author(s):  
Jozef Cernecky ◽  
Jan Koniar ◽  
Zuzana Brodnianska
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Cfd Simulation ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Temperature Fields ◽  
Transfer Coefficients ◽  
Heat Transfer Intensification ◽  
Heat Transfer Coefficients ◽  
Forced Air

Abstract The paper deals with a study of the effect of regulating elements on local values of heat transfer coefficients along shaped heat exchange surfaces with forced air convection. The use of combined methods of heat transfer intensification, i.e. a combination of regulating elements with appropriately shaped heat exchange areas seems to be highly effective. The study focused on the analysis of local values of heat transfer coefficients in indicated cuts, in distances expressed as a ratio x/s for 0; 0.33; 0.66 and 1. As can be seen from our findings, in given conditions the regulating elements can increase the values of local heat transfer coefficients along shaped heat exchange surfaces. An optical method of holographic interferometry was used for the experimental research into temperature fields in the vicinity of heat exchange surfaces. The obtained values correspond very well with those of local heat transfer coefficients αx, recorded in a CFD simulation.

scholarly journals Heat Transfer Coefficient Determination in a Gravity Die Casting Process with Local Air Gap Formation and Contact Pressure Using Experimental Evaluation and Numerical Simulation

2021 ◽  
Author(s):  
T. Vossel ◽  
N. Wolff ◽  
B. Pustal ◽  
A. Bührig-Polaczek ◽  
M. Ahmadein
Keyword(s):  
Heat Transfer ◽  
Contact Pressure ◽  
Local Heat Transfer ◽  
Casting Process ◽  
Local Heat ◽  
Air Gap ◽  
Gap Formation ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Die Casting Process

AbstractAnticipating the processes and parameters involved for accomplishing a sound metal casting requires an in-depth understanding of the underlying behaviors characterizing a liquid melt solidifying inside its mold. Heat balance represents a major factor in describing the thermal conditions in a casting process and one of its main influences is the heat transfer between the casting and its surroundings. Local heat transfer coefficients describe how well heat can be transferred from one body or material to another. This paper will discuss the estimation of these coefficients in a gravity die casting process with local air gap formation and heat shrinkage induced contact pressure. Both an experimental evaluation and a numerical modeling for a solidification simulation will be performed as two means of investigating the local heat transfer coefficients and their local differences for regions with air gap formation or contact pressure when casting A356 (AlSi7Mg0.3).

Sign in / Sign up

Export Citation Format

Share Document