Three-Dimensional Velocity and Scalar Field Measurements of an Airfoil Trailing Edge With Slot Film Cooling: The Effect of an Internal Structure in the Slot

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Julia Ling ◽  
Sayuri D. Yapa ◽  
Michael J. Benson ◽  
Christopher J. Elkins ◽  
John K. Eaton
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Field Measurements ◽  
Resonance Imaging ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Horseshoe Vortices ◽  
Edge Span ◽  
Slot Film Cooling

Measurements of the 3D velocity and concentration fields were obtained using magnetic resonance imaging for a pressure-side cutback film cooling experiment. The cutback geometry consisted of rectangular slots separated by straight lands; inside each of the slots was an airfoil-shaped blockage. The results from this trailing edge configuration, the “island airfoil,” are compared to the results obtained with the “generic airfoil,” a geometry with narrower slots, wider, tapered lands, and no blockages. The objective was to determine how the narrower lands and internal blockages affected the average film cooling effectiveness and the spanwise uniformity. Velocimetry data revealed that strong horseshoe vortices formed around the blockages in the slots, which resulted in greater coolant nonuniformity on the airfoil breakout surface and in the wake. The thinner lands of the island airfoil allowed the coolant to cover a larger fraction of the trailing edge span, giving a much higher spanwise-averaged surface effectiveness, especially near the slot exit where the generic airfoil lands are widest.

3D Velocity and Scalar Field Measurements of an Airfoil Trailing Edge With Slot Film Cooling: The Effect of an Internal Structure in the Slot

2012 ◽  
Author(s):  
Julia Ling ◽  
Sayuri D. Yapa ◽  
Michael J. Benson ◽  
Christopher J. Elkins ◽  
John K. Eaton
Keyword(s):  
Film Cooling ◽  
Field Measurements ◽  
Pressure Side ◽  
Resonance Imaging ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Horseshoe Vortices ◽  
Edge Span ◽  
Slot Film Cooling

Measurements of the 3D velocity and concentration fields were obtained using magnetic resonance imaging for a pressure side cutback film cooling experiment. The cutback geometry consisted of rectangular slots separated by straight lands; inside each of the slots was an airfoil-shaped blockage. The results from this trailing edge configuration, the “island airfoil,” are compared to the results obtained with the “generic airfoil,” a geometry with narrower slots, wider, tapered lands, and no blockages. The objective was to determine how the narrower lands and internal blockages affected the average film cooling effectiveness and the spanwise uniformity. Velocimetry data revealed that strong horseshoe vortices formed around the blockages in the slots, which resulted in greater coolant non-uniformity on the airfoil breakout surface and in the wake. The thinner lands of the island airfoil allowed the coolant to cover a larger fraction of the trailing edge span, giving a much higher spanwise-averaged surface effectiveness, especially near the slot exit where the generic airfoil lands are widest.

Assessment of a Double Hole Film Cooling Geometry Using S-PIV and PSP

2013 ◽  
Author(s):  
Lesley M. Wright ◽  
Stephen T. McClain ◽  
Charles P. Brown ◽  
Weston V. Harmon
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Three Dimensional ◽  
Field Measurements ◽  
Secondary Flows ◽  
Cylindrical Hole ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Hole Geometry ◽  
Compound Angle

A novel, double hole film cooling configuration is investigated as an alternative to traditional cylindrical and fanshaped, laidback holes. This experimental investigation utilizes a Stereo-Particle Image Velocimetry (S-PIV) to quantitatively assess the ability of the proposed, double hole geometry to weaken or mitigate the counter-rotating vortices formed within the jet structure. The three-dimensional flow field measurements are combined with surface film cooling effectiveness measurements obtained using Pressure Sensitive Paint (PSP). The double hole geometry consists of two compound angle holes. The inclination of each hole is θ = 35°, and the compound angle of the holes is β = ± 45° (with the holes angled toward one another). The simple angle cylindrical and shaped holes both have an inclination angle of θ = 35°. The blowing ratio is varied from M = 0.5 to 1.5 for all three film cooling geometries while the density ratio is maintained at DR = 1.0. Time averaged velocity distributions are obtained for both the mainstream and coolant flows at five streamwise planes across the fluid domain (x/d = −4, 0, 1, 5, and 10). These transverse velocity distributions are combined with the detailed film cooling effectiveness distributions on the surface to evaluate the proposed double hole configuration (compared to the traditional hole designs). The fanshaped, laidback geometry effectively reduces the strength of the kidney-shaped vortices within the structure of the jet (over the entire range of blowing ratios considered). The three-dimensional velocity field measurements indicate the secondary flows formed from the double hole geometry strengthen in the plane perpendicular to the mainstream flow. At the exit of the double hole geometry, the streamwise momentum of the jets is reduced (compared to the single, cylindrical hole), and the geometry offers improved film cooling coverage. However, moving downstream in the steamwise direction, the two jets form a single jet, and the counter-rotating vortices are comparable to those formed within the jet from a single, cylindrical hole. These strong secondary flows lift the coolant off the surface, and the film cooling coverage offered by the double hole geometry is reduced.

Investigation on the Effect of Different Lands on Trailing Edge Slot Film Cooling

2018 ◽  
Vol 0 (0) ◽  
Author(s):  
Yang Xu ◽  
Hui-ren Zhu ◽  
Wei-jiang Xu ◽  
Jian-sheng Wei
Keyword(s):  
Nusselt Number ◽  
Film Cooling ◽  
Turbine Blades ◽  
Experimental Studies ◽  
Navier Stokes ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Wall Functions ◽  
Film Cooling Effectiveness ◽  
Slot Film Cooling

Abstract Trailing edge slot film cooling is a widely used method for protecting the trailing edge of turbine blades from hot gas impingement. The structures that separate the slots, known as “lands,” come in a variety of configurations. This paper presents the effects of the trailing edge with different lands on the film cooling performance. Experimental studies are conducted on the film cooling effectiveness and Nusselt number with different lands. Four trailing edge configurations, including the straight lands, the beveling lands, the fillet lands and the tapered lands are considered under four blowing ratios (0.5, 0.7, 1.0 and 1.5). The Reynolds numbers of mainstream is fixed as 375,000. Film cooling effectiveness and Nusselt number performances are measured by transient liquid crystal measurement technique. Reynolds-averaged Navier-Stokes (RANS) simulation with realizable k-ε turbulence model and enhanced wall functions are performed using a commercial code Fluent. In each case, the slot height is kept constant. It is shown that the beveling lands, the fillet lands and the tapered lands have higher cooling effectiveness and lower Nusselt number compared with the straight lands. Under higher blowing ratios, the trailing edges of all four lands have higher cooling effectiveness and higher Nusselt number.

Numerical Predictions of Three-Dimensional Unsteady Turbulent Film-Cooling for Trailing Edge of Gas-Turbine Blade Using Large Eddy Simulation

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Ahmed Khalil ◽  
Hatem Kayed ◽  
Abdallah Hanafi ◽  
Medhat Nemitallah ◽  
Mohamed Habib
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Gas Turbine Blades ◽  
Blowing Ratio ◽  
Eddy Simulation

This work investigates the performance of film-cooling on trailing edge of gas turbine blades using unsteady three-dimensional numerical model adopting large eddy simulation (LES) turbulence scheme in a low Mach number flow regime. This study is concerned with the scaling parameters affecting effectiveness and heat transfer performance on the trailing edge, as a critical design parameter, of gas turbine blades. Simulations were performed using ANSYS-fluentworkbench 17.2. High quality mesh was adapted, whereas the size of cells adjacent to the wall was optimized carefully to sufficiently resolve the boundary layer to obtain insight predictions of the film-cooling effectiveness on a flat plate downstream the slot opening. Blowing ratio, density ratio, Reynolds number, and the turbulence intensity of the mainstream and coolant flow are optimally examined against the film-cooling effectiveness. The predicted results showed a great agreement when compared with the experiments. The results show a distinctive behavior of the cooling effectiveness with blowing ratio variation as it has a dip in vicinity of unity which is explained by the behavior of the vortex entrainment and momentum of coolant flow. The negative effect of the turbulence intensity on the cooling effectiveness is demonstrated as well.

Experimental and Numerical Investigation of Trailing Edge Film Cooling by Circular Coolant Wall Jets Ejected From a Slot With Internal Rib Arrays

2003 ◽  
Author(s):  
P. Martini ◽  
A. Schulz ◽  
S. Wittig
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Numerical Data ◽  
Trailing Edge ◽  
Adiabatic Wall ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Edge Features ◽  
Cooling Air

The present study concentrates on the experimental and computational investigation of a cooled trailing edge in a modern turbine blade. The trailing edge features a pressure side cutback and a slot, stiffened by two rows of evenly spaced ribs in an inline configuration. Cooling air is ejected through the slot and forms a cooling film on the trailing edge cutback region. In the present configuration the lateral spacing of the ribs equals two times their width. The height of the ribs, i.e. the height of the slot equals their width. Since the ribs are provided with fillet radii of half the slot height in size, circular coolant jets are exiting the slot tangentially to the trailing edge cutback. The adiabatic wall temperature mappings on the trailing edge cutback indicate that strong three-dimensional flow interaction between the coolant jets and the hot main flow takes place in such a way that two or more coolant jets coalesce depending on the blowing ratio. Experimental and numerical data to be presented in the present study include adiabatic film cooling effectiveness on the trailing edge cutback, the pressure distribution along the internal ribbed passage as well as slot discharge coefficients for different blowing ratios ranging from M = 0.35 to 1.1.

Experimental and Numerical Investigation of Trailing Edge Film Cooling by Circular Coolant Wall Jets Ejected From a Slot With Internal Rib Arrays

2004 ◽  
Vol 126 (2) ◽  
pp. 229-236 ◽  
Author(s):  
P. Martini ◽  
A. Schulz
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Numerical Data ◽  
Trailing Edge ◽  
Adiabatic Wall ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Edge Features ◽  
Cooling Air

The present study concentrates on the experimental and computational investigation of a cooled trailing edge in a modern turbine blade. The trailing edge features a pressure side cutback and a slot, stiffened by two rows of evenly spaced ribs in an inline configuration. Cooling air is ejected through the slot and forms a cooling film on the trailing edge cutback region. In the present configuration the lateral spacing of the ribs equals two times their width. The height of the ribs, i.e., the height of the slot equals their width. Since the ribs are provided with fillet radii of half the slot height in size, circular coolant jets are exiting the slot tangentially to the trailing edge cutback. The adiabatic wall temperature mappings on the trailing edge cutback indicate that strong three-dimensional flow interaction between the coolant jets and the hot main flow takes place in such a way that two or more coolant jets coalesce depending on the blowing ratio. Experimental and numerical data to be presented in the present study include adiabatic film cooling effectiveness on the trailing edge cutback, the pressure distribution along the internal ribbed passage as well as slot discharge coefficients for different blowing ratios ranging from M=0.35 to 1.1.

Film-Cooled Trailing Edge Measurements: 3D Velocity and Scalar Field

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Michael Benson ◽  
Gregory Laskowski ◽  
Chris Elkins ◽  
John K. Eaton
Keyword(s):  
Magnetic Resonance ◽  
Film Cooling ◽  
Three Dimensional ◽  
Turbulent Regime ◽  
Velocity Measurements ◽  
Trailing Edge ◽  
Mean Velocity ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Longitudinal Vortices

Aircraft turbine blade trailing edges commonly are cooled by blowing air through pressure-side cutback slots. The surface effectiveness is governed by the rate of mixing of the coolant with the mainstream, which is typically much faster than predicted by CFD models. Three-dimensional velocity and coolant concentration fields were measured in and around a cutback slot using a simple uncambered airfoil with a realistic trailing edge cooling geometry at a Reynolds number of 110,000 based on airfoil chord length, which is lower than practical engines but still in the turbulent regime. The results were obtained using magnetic resonance imaging (MRI) techniques in a water flow apparatus. Magnetic resonance concentration (MRC) scans measured the concentration distribution with a spatial resolution of 0.5 mm3 (compared to a slot height of 5 mm) and an uncertainty near 5%. Magnetic resonance velocimetry (MRV) was used to acquire 3D, three-component mean velocity measurements with a resolution of 1.0 mm3. Coupled concentration and velocity measurements were used to identify flow structures contributing to the rapid mixing, including longitudinal vortices and separation bubbles. Velocity measurements at several locations were compared with an unsteady RANS model. Concentration measurements extrapolated to the surface provided film cooling effectiveness and showed that the longitudinal vortices decreased effectiveness near the lands and reduced the average film cooling effectiveness.

Sign in / Sign up

Export Citation Format

Share Document