Effects of Gap Leakage on Fluid Flow in a Contoured Turbine Nozzle Guide Vane

2000 ◽  
Author(s):  
Y.-L. Lin ◽  
T. I-P. Shih ◽  
M. K. Chyu ◽  
R. S. Bunker
Keyword(s):  
Computational Study ◽  
Guide Vane ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Navier Stokes ◽  
Hot Gas ◽  
Nozzle Guide Vane ◽  
A Cell ◽  
Nozzle Guide ◽  
Volume Method

Computations were performed to study the three-dimensional flow in a nozzle guide vane with leakage issuing from a narrow gap with a backward-facing step located upstream of the airfoil on each endwall. The nozzle guide vane investigated has one flat and one contoured endwall. For the contoured endwall, two configurations of the same contouring profile were investigated with and without gap leakage. In one configuration, all contouring is upstream of the airfoil passage. In the other, the contouring starts upstream of the airfoil passage and continues through it. Results obtained show that when there is gap leakage, secondary flows are reduced at all endwalls for both nozzle configurations investigated. Without gap leakage, secondary flows are reduced only on the contoured endwall in which the contouring started upstream of the airfoil passage and continued through it. When all of the contouring is located upstream of the airfoil passage, there is considerable hot gas ingestion into the gap at both endwalls. When the contouring starts upstream of the airfoil passage and continues throught it, hot gas ingestion was minimal at the contoured endwall and greatly reduced at the flat endwall. This computational study is based on the ensemble-averaged conservation equations of mass, momentum (compressible Navier-Stokes), and energy. Effects of turbulence were modeled by the low Reynolds number shear-stress transport k-ω model. Solutions were generated by a cell-centered finite-volume method that uses third-order accurate flux-difference splitting of Roe with limiters and multigrid acceleration of a diagonalized ADI scheme with local time stepping on patched structured grids.

Control of Secondary Flows in a Turbine Nozzle Guide Vane by Endwall Contouring

2000 ◽  
Author(s):  
T. I-P. Shih ◽  
Y.-L. Lin ◽  
T. W. Simon
Keyword(s):  
Film Cooling ◽  
Computational Study ◽  
Guide Vane ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Navier Stokes ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
A Cell ◽  
Nozzle Guide

Computations were performed to study the three-dimensional flow and temperature distribution in a nozzle guide vane that has one flat and one contoured endwall with and without film cooling injected from two slots, one on each endwall located just upstream of the airfoil. For the contoured endwall, two locations of the same contouring were investigated, one with all contouring upstream of the airfoil and another with the contouring starting upstream of the airfoil and continuing through the airfoil passage. Results obtained show that when the contouring is all upstream of the airfoil, secondary flows on both the flat and the contoured endwalls are similar in magnitude. When the contouring starts upstream of the airfoil and continues through the airfoil passage, secondary flows on the contoured endwall are markedly weaker than those on the flat endwall. With weaker secondary flows on the contoured endwall, film-cooling effectiveness there is greatly improved. This computational study is based on the ensemble-averaged conservation equations of mass, momentum (compressible Navier-Stokes), and energy. Effects of turbulence were modeled by the low Reynolds number shear-stress transport k-ω model. Solutions were generated by a cell-centered, finite-volume method that uses third-order accurate flux-difference splitting of Roe with limiters and multigrid acceleration of a diagonalized ADI scheme with local time stepping on patched/embedded structured grids.

The Extension of a Solution-Adaptive Three-Dimensional Navier–Stokes Solver Toward Geometries of Arbitrary Complexity

1993 ◽  
Vol 115 (2) ◽  
pp. 283-295 ◽  
Author(s):  
W. N. Dawes
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Recent Developments ◽  
Nozzle Guide

This paper describes recent developments to a three-dimensional, unstructured mesh, solution-adaptive Navier–Stokes solver. By adopting a simple, pragmatic but systematic approach to mesh generation, the range of simulations that can be attempted is extended toward arbitrary geometries. The combined benefits of the approach result in a powerful analytical ability. Solutions for a wide range of flows are presented, including a transonic compressor rotor, a centrifugal impeller, a steam turbine nozzle guide vane with casing extraction belt, the internal coolant passage of a radial inflow turbine, and a turbine disk cavity flow.

scholarly journals Computations of Film Cooling From Holes With Struts

1999 ◽  
Author(s):  
T. I-P. Shih ◽  
Y.-L. Lin ◽  
M. K. Chyu ◽  
S. Gogineni
Keyword(s):  
Film Cooling ◽  
Computational Study ◽  
Three Dimensional ◽  
Protective Layer ◽  
Navier Stokes ◽  
Time Stepping ◽  
Cooling Hole ◽  
A Cell ◽  
Volume Method ◽  
Film Cooling Holes

Computations were performed to study the three-dimensional flow and heat transfer on a flat plate cooled by jets, injected from a plenum through one row of film-cooling holes in which each hole is fitted with a strut in the form of a circular cylinder. Three different configurations of the film-cooling hole were investigated: without strut, with streamwise strut, and with spanwise strut. For all configurations, the film-cooling holes are inclined at 35°, and the coolant-to-mainflow density and mass-flux ratios are 1.6 and 0.5, respectively. The focus of this study is to understand how struts in holes affect film cooling jets and their interactions with the mainflow in forming a protective layer of cooler fluid over the plate. This computational study is based on the ensemble-averaged conservation equations of mass, momentum (compressible Navier-Stokes), and energy. Effects of turbulence was modeled by a low Reynolds number k-ω closure known as the shear-stress-transport (SST) model. Solutions were generated by a cell-centered finite-volume method that uses third-order accurate flux-difference splitting of Roe with limiters, multigrid acceleration of a diagonalized ADI scheme with local time stepping, and patched/overlapped structured grids. In the computations, the flow is resolved not just in the cooling-jet/mainflow interaction region, but also inside the film-cooling holes and in the plenum. Computed results for adiabatic effectiveness for the case without struts were compared with experimental data, and reasonably good agreements were obtained.

Toward Improved Throughflow Capability: The Use of Three-Dimensional Viscous Flow Solvers in a Multistage Environment

1992 ◽  
Vol 114 (1) ◽  
pp. 8-17 ◽  
Author(s):  
W. N. Dawes
Keyword(s):  
Experimental Evidence ◽  
Guide Vane ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Flow Properties ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Blade Row ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

A methodology is presented for simulating turbomachinery blade rows in a multistage environment by deploying a standard three-dimensional Navier–Stokes solver simultaneously on a number of blade rows. The principal assumptions are that the flow is steady relative to each blade row individually and that the rows can communicate via inter-row mixing planes. These mixing planes introduce circumferential averaging of flow properties but preserve quite general radial variations. Additionally, each blade can be simulated in three-dimensional or axisymmetrically (in the spirit of throughflow analysis) and a series of axisymmetric rows can be considered together with one three-dimensional row to provide, cheaply, a machine environment for that row. Two applications are presented: a transonic compressor rotor and a steam turbine nozzle guide vane simulated both isolated and as part of a stage. In both cases the behavior of the blade considered in isolation was different to when considered as part of a stage and in both cases was in much closer agreement with the experimental evidence.

Aero-Thermal Aspects of Film Cooled Nozzle Guide Vane Endwalls: Part 2 — Thermal Measurements

2020 ◽  
Author(s):  
Mahmood H. Alqefl ◽  
Kedar P. Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong W. Kim ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Complex Flow ◽  
Cooling Flows ◽  
Thermal Measurements ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Abstract Flow over gas turbine endwalls is complex and highly three-dimensional. As boundaries for modern engine designs are pushed, this already-complex flow is affected by aggressive application of film cooling flows that actively interact. This two-part study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The approach flow conditions represent flow exiting a low-NOx combustor. The test section includes geometric and cooling details of a combustor-turbine interface in addition to endwall film cooling flows injected upstream of the passage. The first part of this study describes in detail, the passage aerodynamics as affected by injection of cooling flows. It reveals a system of secondary flows, including the newly-discovered Impingement Vortex, which redefines our understanding of the aerodynamics of flow in a modern, film-cooled, first-stage vane row. The second part investigates, through thermal measurements, the distribution, mixing and disruption of cooling flows over the endwall. Measurements are made with and without active endwall film cooling. Descriptions are made through adiabatic surface effectiveness measurements and correlations with in-passage velocity (presented in part one) and thermal fields. Results show that the newly-discovered impingement vortex has a positive effect on coolant distribution through passage vortex suppression and by carrying the coolant to hard-to-cool regions in the passage, including the pressure surface near the endwall.

AERO-THERMAL ASPECTS OF FILM COOLED NOZZLE GUIDE VANE ENDWALLS - PART 2: THERMAL MEASUREMENTS

2021 ◽  
pp. 1-39
Author(s):  
Mahmood H. Alqefl ◽  
Kedar P. Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong Kim ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Complex Flow ◽  
Cooling Flows ◽  
Thermal Measurements ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Abstract Flow over gas turbine endwalls is complex and highly three-dimensional. As boundaries for modern engine designs are pushed, this already-complex flow is affected by aggressive application of film cooling flows that actively interact. This two-part study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The approach flow conditions represent flow exiting a low-NOx combustor. The test section includes geometric and cooling details of a combustor-turbine interface in addition to endwall film cooling flows injected upstream of the passage. The first part of this study describes in detail, the passage aerodynamics as affected by injection of cooling flows. It reveals a system of secondary flows, including the newly-discovered Impingement Vortex, which redefines our understanding of the aerodynamics of flow in a modern, film-cooled, first-stage vane row. The second part investigates, through thermal measurements, the distribution, mixing and disruption of cooling flows over the endwall. Measurements are made with and without active endwall film cooling. Descriptions are made through adiabatic surface effectiveness measurements and correlations with in-passage velocity (presented in part one) and thermal fields. Results show that the newly-discovered impingement vortex has a positive effect on coolant distribution through passage vortex suppression and by carrying the coolant to hard-to-cool regions in the passage, including the pressure surface near the endwall.

Aero-Thermal Aspects of Film Cooled Nozzle Guide Vane Endwalls: Part 1 — Aerodynamics

2020 ◽  
Author(s):  
Mahmood H. Alqefl ◽  
Kedar P. Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong W. Kim ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Protective Film ◽  
Cooling Flows ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Abstract The first stage turbine of a modern gas turbine is subjected to high thermal loads which lead to a need for aggressive cooling schemes to protect its components from melting. Endwalls are particularly challenging to cool due to the complex system of secondary flows near them that wash the protective film coolants into the mainstream. This paper shows that without including combustor cooling, the complex secondary flow physics are not representative of modern engines. Aggressive injection of all cooling flows upstream of the passage is expected to interact and change passage aerodynamics and, subsequently, mixing and transport of coolants. This study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The test section involves an engine-representative combustor-turbine interface geometry, combustor coolant flow and endwall film cooling flow injected upstream of a linear cascade. The approach flow conditions represent flow exiting a cooled, low-NOx combustor. This first part of this two-part study aims to understand the complex aerodynamics near the endwall through detailed measurements of passage three-dimensional velocity fields with and without endwall film cooling. The aerodynamic measurements reveal a dominant vortex in the passage, named here as the Impingement Vortex, that opposes the passage vortex formed at the airfoil leading edge plane. This Impingement Vortex completely changes our description of flow over a modern film cooled endwall.

Aero-thermal Aspects of Film Cooled Nozzle Guide Vane Endwall - Part 1: Aerodynamics

2021 ◽  
pp. 1-54
Author(s):  
Mahmood H. Alqefl ◽  
Kedar P. Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong W. Kim ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Protective Film ◽  
Cooling Flows ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Abstract The first stage turbine of a modern gas turbine is subjected to high thermal loads which lead to a need for aggressive cooling schemes to protect its components from melting. Endwalls are particularly challenging to cool due to the complex system of secondary flows near them that wash the protective film coolants into the mainstream. This paper shows that without including combustor cooling, the complex secondary flow physics are not representative of modern engines. Aggressive injection of all cooling flows upstream of the passage is expected to interact and change passage aerodynamics and, subsequently, mixing and transport of coolants. This study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The test section involves an engine-representative combustor-turbine interface geometry, combustor coolant flow and endwall film cooling flow injected upstream of a linear cascade. The approach flow conditions represent flow exiting a cooled, low-NOx combustor. This first part of this two-part study aims to understand the complex aerodynamics near the endwall through detailed measurements of passage three-dimensional velocity fields with and without endwall film cooling. The aerodynamic measurements reveal a dominant vortex in the passage, named here as the Impingement Vortex, that opposes the passage vortex formed at the airfoil leading edge plane. This Impingement Vortex completely changes our description of flow over a modern film cooled endwall.

Numerical Analysis on Effects of the Contoured Endwall on the Three Dimensional Flow Characteristics in an Annular Turbine Nozzle Vane

2007 ◽  
Author(s):  
Wu Sang Lee ◽  
Jin Taek Chung ◽  
Dae Hyun Kim ◽  
Seung Joo Choe
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Leading Edge ◽  
Secondary Flows ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

The three-dimensional flow in a turbine nozzle guide vane passage causes large secondary loss through the passage and increased heat transfer on the blade surface. In order to reduce or control these secondary flows, a linear turbine with contoured endwall configurations was used and changes in the three-dimensional flow field were analyzed and discussed. Contoured endwalls are installed at a location downstream of the saddle point near the leading edge of the pressure side blade and several positions along the centerline of the passage at constant distance. The objective of this study is to document the development of the three-dimensional flow in a turbine nozzle guide vane cascade with modified endwall. In addition, it proposes and appropriates endwall contouring which shows best overall loss reduction performance among the simulated contoured endwall. The results of this study show that the development of passage vortex and cross flow in the cascade composed of one flat and one contoured endwalls are affected by the acceleration which occurs in contoured endwall side. The overall loss is reduced near the flat endwall rather than contoured endwall, the best performance was shown for the case of 10–15% contoured for span-wise, 40–70% length of chord from trailing edge.

Sign in / Sign up

Export Citation Format

Share Document