Numerical Analysis on Effects of the Contoured Endwall on the Three Dimensional Flow Characteristics in an Annular Turbine Nozzle Vane

2007 ◽  
Author(s):  
Wu Sang Lee ◽  
Jin Taek Chung ◽  
Dae Hyun Kim ◽  
Seung Joo Choe
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Leading Edge ◽  
Secondary Flows ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

The three-dimensional flow in a turbine nozzle guide vane passage causes large secondary loss through the passage and increased heat transfer on the blade surface. In order to reduce or control these secondary flows, a linear turbine with contoured endwall configurations was used and changes in the three-dimensional flow field were analyzed and discussed. Contoured endwalls are installed at a location downstream of the saddle point near the leading edge of the pressure side blade and several positions along the centerline of the passage at constant distance. The objective of this study is to document the development of the three-dimensional flow in a turbine nozzle guide vane cascade with modified endwall. In addition, it proposes and appropriates endwall contouring which shows best overall loss reduction performance among the simulated contoured endwall. The results of this study show that the development of passage vortex and cross flow in the cascade composed of one flat and one contoured endwalls are affected by the acceleration which occurs in contoured endwall side. The overall loss is reduced near the flat endwall rather than contoured endwall, the best performance was shown for the case of 10–15% contoured for span-wise, 40–70% length of chord from trailing edge.

scholarly journals Effects of Tip Endwall Contouring on the Three Dimensional Flow Field in an Annular Turbine Nozzle Guide Vane: Part 2 — Numerical Investigation

1985 ◽  
Author(s):  
Tony Arts
Keyword(s):  
Flow Field ◽  
Numerical Investigation ◽  
Guide Vane ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Nozzle Guide Vane ◽  
Contour Plots ◽  
Endwall Contouring ◽  
Nozzle Guide

This paper describes the numerical investigation of the three dimensional flow through a low speed, low aspect ratio, high turning annular turbine nozzle guide vane with meridional tip endwall contouring. This rotational flow field has been simulated using a finite volume discretization and a time marching technique to solve the three dimensional, time dependent Euler equations expressed in a cylindrical coordinates system. The results are presented under the form of contour plots, spanwise pitch-averaged distributions and blade static pressure distributions. Detailed comparisons with the measurements described in part I of the paper are also provided.

Aero-Thermal Aspects of Film Cooled Nozzle Guide Vane Endwalls: Part 1 — Aerodynamics

2020 ◽  
Author(s):  
Mahmood H. Alqefl ◽  
Kedar P. Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong W. Kim ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Protective Film ◽  
Cooling Flows ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Abstract The first stage turbine of a modern gas turbine is subjected to high thermal loads which lead to a need for aggressive cooling schemes to protect its components from melting. Endwalls are particularly challenging to cool due to the complex system of secondary flows near them that wash the protective film coolants into the mainstream. This paper shows that without including combustor cooling, the complex secondary flow physics are not representative of modern engines. Aggressive injection of all cooling flows upstream of the passage is expected to interact and change passage aerodynamics and, subsequently, mixing and transport of coolants. This study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The test section involves an engine-representative combustor-turbine interface geometry, combustor coolant flow and endwall film cooling flow injected upstream of a linear cascade. The approach flow conditions represent flow exiting a cooled, low-NOx combustor. This first part of this two-part study aims to understand the complex aerodynamics near the endwall through detailed measurements of passage three-dimensional velocity fields with and without endwall film cooling. The aerodynamic measurements reveal a dominant vortex in the passage, named here as the Impingement Vortex, that opposes the passage vortex formed at the airfoil leading edge plane. This Impingement Vortex completely changes our description of flow over a modern film cooled endwall.

Aero-thermal Aspects of Film Cooled Nozzle Guide Vane Endwall - Part 1: Aerodynamics

2021 ◽  
pp. 1-54
Author(s):  
Mahmood H. Alqefl ◽  
Kedar P. Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong W. Kim ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Protective Film ◽  
Cooling Flows ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Abstract The first stage turbine of a modern gas turbine is subjected to high thermal loads which lead to a need for aggressive cooling schemes to protect its components from melting. Endwalls are particularly challenging to cool due to the complex system of secondary flows near them that wash the protective film coolants into the mainstream. This paper shows that without including combustor cooling, the complex secondary flow physics are not representative of modern engines. Aggressive injection of all cooling flows upstream of the passage is expected to interact and change passage aerodynamics and, subsequently, mixing and transport of coolants. This study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The test section involves an engine-representative combustor-turbine interface geometry, combustor coolant flow and endwall film cooling flow injected upstream of a linear cascade. The approach flow conditions represent flow exiting a cooled, low-NOx combustor. This first part of this two-part study aims to understand the complex aerodynamics near the endwall through detailed measurements of passage three-dimensional velocity fields with and without endwall film cooling. The aerodynamic measurements reveal a dominant vortex in the passage, named here as the Impingement Vortex, that opposes the passage vortex formed at the airfoil leading edge plane. This Impingement Vortex completely changes our description of flow over a modern film cooled endwall.

Effects of Tip Endwall Contouring on the Three-Dimensional Flow Field in an Annular Turbine Nozzle Guide Vane: Part 1—Experimental Investigation

1985 ◽  
Vol 107 (4) ◽  
pp. 983-990 ◽  
Author(s):  
E. Boletis
Keyword(s):  
Experimental Investigation ◽  
Aspect Ratio ◽  
Guide Vane ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Low Aspect Ratio ◽  
Dimensional Flow ◽  
Nozzle Guide Vane ◽  
Endwall Contouring ◽  
Nozzle Guide

Tip endwall contouring is one of the most effective methods to improve the performance of low aspect ratio turbine vanes [1]. In view of the wide variety of geometric parameters, it appears that only the physical understanding of the three-dimensional flow field will allow us to evaluate the probable benefits of a particular endwall contouring. The paper describes the experimental investigation of the three-dimensional flow through a low-speed, low aspect ratio, high-turning annular turbine nozzle guide vane with meridional tip endwall contouring. The full impact of the effects of tip contouring is evaluated by comparison with the results of a previous study in an annular turbine nozzle guide vane of the same blade and cascade geometry with cylindrical endwalls [12]. In parallel, the present experimental study provides a fully three-dimensional test case for comparison with advanced theoretical calculation methods [15]. The flow is explored by means of double-head, four-hole pressure probes in five axial planes from far upstream to downstream of the blade row. The results are presented in the form of contour plots and spanwise pitch-averaged distributions.

Influence of Pre-History and Leading Edge Contouring on Aero-Performance of a 3D Nozzle Guide Vane

2013 ◽  
Author(s):  
Ranjan Saha ◽  
Boris I. Mamaev ◽  
Jens Fridh ◽  
Björn Laumert ◽  
Torsten H. Fransson
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Stagnation Line ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Turbine Vane ◽  
Loss Coefficients ◽  
Exit Mach Number ◽  
Nozzle Guide

Experiments are conducted to investigate the effect of the pre-history in the aerodynamic performance of a three-dimensional nozzle guide vane with a hub leading edge contouring. The performance is determined with two pneumatic probes (5 hole and 3 hole) concentrating mainly on the endwall. The investigated vane is a geometrically similar gas turbine vane for the first stage with a reference exit Mach number of 0.9. Results are compared for the baseline and filleted cases for a wide range of operating exit Mach numbers from 0.5 to 0.9. The presented data includes loading distributions, loss distributions, fields of exit flow angles, velocity vector and vorticity contour, as well as, mass-averaged loss coefficients. The results show an insignificant influence of the leading edge fillet on the performance of the vane. However, the pre-history (inlet condition) affects significantly in the secondary loss. Additionally, an oil visualization technique yields information about the streamlines on the solid vane surface which allows identifying the locations of secondary flow vortices, stagnation line and saddle point.

Research of Aerodynamic Performance of HP-Turbine with Coolant Injections for Variable Cycle Engine

2011 ◽  
Vol 110-116 ◽  
pp. 1047-1053
Author(s):  
Zhi Gang Liu ◽  
Xiang Jun Fang ◽  
Si Yong Liu ◽  
Ping Wang ◽  
Zhao Yin
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Supersonic Nozzle ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Thermodynamic Cycle ◽  
Aerodynamic Performance ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Transonic Rotor

A highly loaded high-pressure turbine with a supersonic nozzle guide vane and a transonic rotor for a Variable Cycle Engine (VCE) has been investigated. Film cooling strategies were designed for the whole stage, during which the positions, injection orientations and arrangements of cooling holes were confirmed. Three-dimensional steady numerical simulations have been performed in the two operation modes of low and high bypass ratio with different thermodynamic cycle parameters according to the VCE and the coolant injections have been simulated by means of additional source term method. The influences of coolant injections in the fully cooled turbine stage on aerodynamic performance and flow characteristics have been analyzed. The results indicate that, the supersonic nozzle guide vane, over-expansion degree of main flows, fluctuations of static pressure and intensity of corner vortex are lessened or alleviated. In the transonic rotor, expansion and doing work capabilities in the mixed fluid are strengthened. Proper coolants injections are beneficial to the flow characteristics in the blade passage.

Aero-Thermal Aspects of Film Cooled Nozzle Guide Vane Endwalls: Part 2 — Thermal Measurements

2020 ◽  
Author(s):  
Mahmood H. Alqefl ◽  
Kedar P. Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong W. Kim ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Complex Flow ◽  
Cooling Flows ◽  
Thermal Measurements ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Abstract Flow over gas turbine endwalls is complex and highly three-dimensional. As boundaries for modern engine designs are pushed, this already-complex flow is affected by aggressive application of film cooling flows that actively interact. This two-part study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The approach flow conditions represent flow exiting a low-NOx combustor. The test section includes geometric and cooling details of a combustor-turbine interface in addition to endwall film cooling flows injected upstream of the passage. The first part of this study describes in detail, the passage aerodynamics as affected by injection of cooling flows. It reveals a system of secondary flows, including the newly-discovered Impingement Vortex, which redefines our understanding of the aerodynamics of flow in a modern, film-cooled, first-stage vane row. The second part investigates, through thermal measurements, the distribution, mixing and disruption of cooling flows over the endwall. Measurements are made with and without active endwall film cooling. Descriptions are made through adiabatic surface effectiveness measurements and correlations with in-passage velocity (presented in part one) and thermal fields. Results show that the newly-discovered impingement vortex has a positive effect on coolant distribution through passage vortex suppression and by carrying the coolant to hard-to-cool regions in the passage, including the pressure surface near the endwall.

Influence of Prehistory and Leading Edge Contouring on Aero Performance of a Three-Dimensional Nozzle Guide Vane

2014 ◽  
Vol 136 (7) ◽  
Author(s):  
Ranjan Saha ◽  
Boris I. Mamaev ◽  
Jens Fridh ◽  
Björn Laumert ◽  
Torsten H. Fransson
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Stagnation Line ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Loss Coefficients ◽  
Exit Mach Number ◽  
Nozzle Guide ◽  
End Wall

Experiments are conducted to investigate the effect of the prehistory in the aerodynamic performance of a three-dimensional nozzle guide vane with a hub leading edge contouring. The performance is determined with two pneumatic probes (five hole and three hole) concentrating mainly on the end wall. The investigated vane is a geometrically similar gas turbine vane for the first stage with a reference exit Mach number of 0.9. Results are compared for the baseline and filleted cases for a wide range of operating exit Mach numbers from 0.5 to 0.9. The presented data includes loading distributions, loss distributions, fields of exit flow angles, velocity vector, and vorticity contour, as well as mass-averaged loss coefficients. The results show an insignificant influence of the leading edge fillet on the performance of the vane. However, the prehistory (inlet condition) affects significantly in the secondary loss. Additionally, an oil visualization technique yields information about the streamlines on the solid vane surface, which allows identifying the locations of secondary flow vortices, stagnation line, and saddle point.

AERO-THERMAL ASPECTS OF FILM COOLED NOZZLE GUIDE VANE ENDWALLS - PART 2: THERMAL MEASUREMENTS

2021 ◽  
pp. 1-39
Author(s):  
Mahmood H. Alqefl ◽  
Kedar P. Nawathe ◽  
Pingting Chen ◽  
Rui Zhu ◽  
Yong Kim ◽  
...  
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Complex Flow ◽  
Cooling Flows ◽  
Thermal Measurements ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Abstract Flow over gas turbine endwalls is complex and highly three-dimensional. As boundaries for modern engine designs are pushed, this already-complex flow is affected by aggressive application of film cooling flows that actively interact. This two-part study describes, experimentally, the aero-thermal interaction of cooling flows near the endwall of a first stage nozzle guide vane passage. The approach flow conditions represent flow exiting a low-NOx combustor. The test section includes geometric and cooling details of a combustor-turbine interface in addition to endwall film cooling flows injected upstream of the passage. The first part of this study describes in detail, the passage aerodynamics as affected by injection of cooling flows. It reveals a system of secondary flows, including the newly-discovered Impingement Vortex, which redefines our understanding of the aerodynamics of flow in a modern, film-cooled, first-stage vane row. The second part investigates, through thermal measurements, the distribution, mixing and disruption of cooling flows over the endwall. Measurements are made with and without active endwall film cooling. Descriptions are made through adiabatic surface effectiveness measurements and correlations with in-passage velocity (presented in part one) and thermal fields. Results show that the newly-discovered impingement vortex has a positive effect on coolant distribution through passage vortex suppression and by carrying the coolant to hard-to-cool regions in the passage, including the pressure surface near the endwall.

Sign in / Sign up

Export Citation Format

Share Document