Experimental Study of Thermal Performance and Pressure Drop in Compact Heat Exchanger Installed in Automotive

2006 ◽  
Author(s):  
M. H. Saidi ◽  
A. A. Mozafari ◽  
A. R. Esmaeili Sany ◽  
J. Neyestani
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Operating Conditions ◽  
Design Stage ◽  
Practical Usefulness ◽  
Experimental Prediction ◽  
Wide Range

In this Study, radiator performance for passenger car has been studied experimentally in wide range of operating conditions. Experimental prediction of Nusselt number and heat transfer coefficient for coolant in radiator tubes are also performed with ε–NTU method. The total effectiveness coefficient of radiator and heat transfer coefficient in air side is calculated via try and error method considering experimental data. The Colburn factor and pressure drop are also estimated for this heat exchanger. Examples of application demonstrate the practical usefulness of this method to provide empirical data which can be used during the design stage.

Numerical simulation of the effect of baffle cut and baffle spacing on shell side heat exchanger performance using CFD

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Swanand Gaikwad ◽  
Ashish Parmar
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Numerical Results ◽  
Shell Side ◽  
Tube Heat Exchanger ◽  
Shell And Tube ◽  
Two Parameters

AbstractHeat exchangers possess a significant role in energy transmission and energy generation in most industries. In this work, a three-dimensional simulation has been carried out of a shell and tube heat exchanger (STHX) consisting of segmental baffles. The investigation involves using the commercial code of ANSYS CFX, which incorporates the modeling, meshing, and usage of the Finite Element Method to yield numerical results. Much work is available in the literature regarding the effect of baffle cut and baffle spacing as two different entities, but some uncertainty pertains when we discuss the combination of these two parameters. This study aims to find an appropriate mix of baffle cut and baffle spacing for the efficient functioning of a shell and tube heat exchanger. Two parameters are tested: the baffle cuts at 30, 35, 40% of the shell-inside diameter, and the baffle spacing’s to fit 6,8,10 baffles within the heat exchanger. The numerical results showed the role of the studied parameters on the shell side heat transfer coefficient and the pressure drop in the shell and tube heat exchanger. The investigation shows an increase in the shell side heat transfer coefficient of 13.13% when going from 6 to 8 baffle configuration and a 23.10% acclivity for the change of six baffles to 10, for a specific baffle cut. Evidence also shows a rise in the pressure drop with an increase in the baffle spacing from the ranges of 44–46.79%, which can be controlled by managing the baffle cut provided.

Heat Transfer Performance of Different Nanofluids Flows in a Helically Coiled Heat Exchanger

2013 ◽  
Vol 832 ◽  
pp. 160-165 ◽  
Author(s):  
Mohammad Alam Khairul ◽  
Rahman Saidur ◽  
Altab Hossain ◽  
Mohammad Abdul Alim ◽  
Islam Mohammed Mahbubul
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Transfer Performance

Helically coiled heat exchangers are globally used in various industrial applications for their high heat transfer performance and compact size. Nanofluids can provide excellent thermal performance of this type of heat exchangers. In the present study, the effect of different nanofluids on the heat transfer performance in a helically coiled heat exchanger is examined. Four different types of nanofluids CuO/water, Al2O3/water, SiO2/water, and ZnO/water with volume fractions 1 vol.% to 4 vol.% was used throughout this analysis and volume flow rate was remained constant at 3 LPM. Results show that the heat transfer coefficient is high for higher particle volume concentration of CuO/water, Al2O3/water and ZnO/water nanofluids, while the values of the friction factor and pressure drop significantly increase with the increase of nanoparticle volume concentration. On the contrary, low heat transfer coefficient was found in higher concentration of SiO2/water nanofluids. The highest enhancement of heat transfer coefficient and lowest friction factor occurred for CuO/water nanofluids among the four nanofluids. However, highest friction factor and lowest heat transfer coefficient were found for SiO2/water nanofluids. The results reveal that, CuO/water nanofluids indicate significant heat transfer performance for helically coiled heat exchanger systems though this nanofluids exhibits higher pressure drop.

Performance Study of Heat Exchangers with Continuous Helical Baffles on Different Inclination Angles

2013 ◽  
Vol 655-657 ◽  
pp. 461-464 ◽  
Author(s):  
Su Fang Song
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Heat Exchangers ◽  
Performance Study ◽  
Three Dimensional Model ◽  
Shell Side ◽  
Inclination Angles

The three-dimensional model of heat exchangers with continuous helical baffles was built. The fluid flow dynamics and heat transfer of shell side in the helical baffled heat exchanger were simulated and calculated. The velocity, pressure and temperature distributions were achieved. The simulation shows that with the same baffle pitch, shell-side heat transfer coefficient increased by 25% and the pressure drop decreases by 18% in helical baffled heat exchanger compared with segmental helical baffles. With the analyzing of the flow and heat transfer in heat exchanger in 5 different inclination angles from 11°to 21°, it can be found that both shell side heat transfer coefficient and pressure drop will reduce respectively by 86% and 52% with the increases 11°to 21°of the inclination angles. Numerical simulation provided reliable theoretical reference for further engineering research of heat exchanger with helical baffles.

scholarly journals Studies on the Heat Transfer Coefficient and Pressure Drop of Several Kinds of Plate Heat Exchanger

1968 ◽  
Vol 32 (11) ◽  
pp. 1127-1132,a1 ◽  
Author(s):  
Katsuto Okada ◽  
Minobu Ono ◽  
Toshio Tomimum ◽  
Hirotaka Konno ◽  
Shigemori Ohtani
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Plate Heat Exchanger ◽  
Plate Heat ◽  
The Heat Transfer Coefficient

A Natural Convection Fin with a Solution-Determined Nonmonotonically Varying Heat Transfer Coefficient

1981 ◽  
Vol 103 (2) ◽  
pp. 218-225 ◽  
Author(s):  
E. M. Sparrow ◽  
S. Acharya
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Natural Convection ◽  
Transfer Coefficient ◽  
First Principles ◽  
Numerical Solutions ◽  
Flow Direction ◽  
Operating Conditions ◽  
Fluid Temperature ◽  
Wide Range

A conjugate conduction-convection analysis has been made for a vertical plate fin which exchanges heat with its fluid environment by natural convection. The analysis is based on a first-principles approach whereby the heat conduction equation for the fin is solved simultaneously with the conservation equations for mass, momentum, and energy in the fluid boundary layer adjacent to the fin. The natural convection heat transfer coefficient is not specified in advance but is one of the results of the numerical solutions. For a wide range of operating conditions, the local heat transfer coefficients were found not to decrease monotonically in the flow direction, as is usual. Rather, the coefficient decreased at first, attained a minimum, and then increased with increasing downstream distance. This behavior was attributed to an enhanced buoyancy resulting from an increase in the wall-to-fluid temperature difference along the streamwise direction. To supplement the first-principles analysis, results were also obtained from a simple adaptation of the conventional fin model.

Experimental Investigation of Heat Transfer Enhancement of Shell and Tube Heat Exchanger Using SnO2-Water and Ag-Water Nanofluids

2019 ◽  
Vol 12 (4) ◽  
Author(s):  
S. V. Sridhar ◽  
R. Karuppasamy ◽  
G. D. Sivakumar
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Convective Heat Transfer Coefficient ◽  
Two Phase ◽  
Tube Heat Exchanger ◽  
Shell And Tube

Abstract In this investigation, the performance of the shell and tube heat exchanger operated with tin nanoparticles-water (SnO2-W) and silver nanoparticles-water (Ag-W) nanofluids was experimentally analyzed. SnO2-W and Ag-W nanofluids were prepared without any surface medication of nanoparticles. The effects of volume concentrations of nanoparticles on thermal conductivity, viscosity, heat transfer coefficient, fiction factor, Nusselt number, and pressure drop were analyzed. The results showed that thermal conductivity of nanofluids increased by 29% and 39% while adding 0.1 wt% of SnO2 and Ag nanoparticles, respectively, due to the unique intrinsic property of the nanoparticles. Further, the convective heat transfer coefficient was enhanced because of improvement of thermal conductivity of the two phase mixture and friction factor increased due to the increases of viscosity and density of nanofluids. Moreover, Ag nanofluid showed superior pressure drop compared to SnO2 nanofluid owing to the improvement of thermophysical properties of nanofluid.

Predicting Heat Transfer From Unsteady Synthetic Jets

2012 ◽  
Vol 134 (8) ◽  
Author(s):  
Mehmet Arik ◽  
Tunc Icoz
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Jet Impingement ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Operating Conditions ◽  
Small Scale ◽  
Wide Range ◽  
The Heat Transfer Coefficient

Synthetic jets are piezo-driven, small-scale, pulsating devices capable of producing highly turbulent jets formed by periodic entrainment and expulsion of the fluid in which they are embedded. The compactness of these devices accompanied by high air velocities provides an exciting opportunity to significantly reduce the size of thermal management systems in electronic packages. A number of researchers have shown the implementations of synthetic jets on heat transfer applications; however, there exists no correlation to analytically predict the heat transfer coefficient for such applications. A closed form correlation was developed to predict the heat transfer coefficient as a function of jet geometry, position, and operating conditions for impinging flow based on experimental data. The proposed correlation was shown to predict the synthetic jet impingement heat transfer within 25% accuracy for a wide range of operating conditions and geometrical variables.

Heat Transfer and Pressure Drop Analysis of Chilled Water and Ice Slurry in a Plate Heat Exchanger

2015 ◽  
Vol 8 (1) ◽  
Author(s):  
Rajinder Singh ◽  
Surendra Singh Kachhwaha
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Plate Heat Exchanger ◽  
Ice Slurry ◽  
Plate Heat ◽  
Overall Heat Transfer Coefficient ◽  
Chilled Water

The present study reports the experimental validation of thermohydraulic modeling for prediction of pressure drop and heat transfer coefficient. Experiments were performed on plate heat exchanger using chilled water and ice slurry as secondary fluids. Propylene glycol (PG) and mono-ethylene glycol (MEG) are used as depressants (10%, 20%, 30%, and 40% concentration) in ice slurry formation. The results show that thermohydraulic modeling predicts the pressure drop and overall heat transfer coefficient for water to water and water to ice slurry within the discrepancy limit of ±15%.

Effects of Pitch and Depth on the Condensation Heat Transfer of R-134a Flowing Through Corrugated Tubes

2011 ◽  
Author(s):  
Suriyan Laohalertdecha ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Condensation Heat Transfer ◽  
Smooth Tube ◽  
Maximum Heat ◽  
Frictional Pressure Drop ◽  
R 134A

The effects of pitch and depth on the condensation heat transfer of R-134a flowing inside corrugated tubes are experimentally investigated. The test section is a horizontal tube-in-tube heat exchanger. The refrigerant flows in the inner tube and the water flows in the annulus. The length of heat exchanger is 2 m. A smooth tube and corrugated tubes having inner diameters of 8.7 mm are used as an inner tube. The corrugation pitches used in this study are 5.08, 6.35, and 8.46 mm. Similarly, the corrugation depths are 1, 1.25, and 1.5 mm. The effects of corrugation pitch and depth on tube wall temperature, heat transfer coefficient and frictional pressure drop are discussed. The results illustrate that the maximum heat transfer coefficient and frictional pressure drop obtained from the corrugated tube are up to 50% and 70% higher than those obtained from the smooth tube, respectively.

Sign in / Sign up

Export Citation Format

Share Document