Decompression Wave Speed in Rich Gas Mixtures at High Pressures (37 MPa) and Implications on Fracture Control Toughness Requirements in Pipeline Design

Author(s):  
K. K. Botros ◽  
J. Geerligs ◽  
R. J. Eiber

Measurements of decompression wave speed in conventional and rich natural gas mixtures following rupture of a high-pressure pipe have been conducted. A high pressure stainless steel rupture tube (internal diameter = 38.1 mm, and 42 m long), has been constructed and instrumented with 16 high frequency-response pressure transducers mounted very close to the rupture end and along the length of the tube to capture the pressure-time traces of the decompression wave. Tests were conducted for initial pressures of 33–37 MPa-a and a temperature range of 21 to 68 °C. The experimentally determined decompression wave speeds were compared to both GASDECOM and PIPEDECOM predictions with and without non-equilibrium condensation delays at phase crossing. The interception points of the isentropes representing the decompression process with the corresponding phase envelope of each mixture were correlated to the respective plateaus observed in the decompression wave speed profiles. Additionally, speeds of sound in the undisturbed gas mixtures at the initial pressures and temperatures were compared to predictions by five equations of state, namely BWRS, AGA-8, Peng-Robinson, Soave-Redlich-Kwong, and GERG. The measured gas decompression curves were used to predict the fracture arrest toughness needed to assure fracture control in natural gas pipelines. The rupture tube test results have shown that the Charpy fracture arrest values predicted using GASEDCOM are within +7 (conservative) and −11% (non-conservative) of the rupture tube predicted values. Similarly, PIPEDECOM with no temperature delay provides fracture arrest values that are within +13 and −20% of the rupture tube predicted values, while PIPEDECOM with a 1 °C temperature delay provides fracture arrest values that are within 0 and −20% of the rupture tube predicted values. Ideally, it would be better if the predicted values by the equations of state were above the rupture tube predicted values to make the predictions conservative but that was not always the case.

2010 ◽  
Vol 132 (5) ◽  
Author(s):  
K. K. Botros ◽  
J. Geerligs ◽  
R. J. Eiber

Measurements of decompression wave speed in conventional and rich natural gas mixtures following rupture of a high-pressure pipe have been conducted. A high-pressure stainless steel rupture tube (internal diameter=38.1 mm and 42 m long) has been constructed and instrumented with 16 high frequency-response pressure transducers mounted very close to the rupture end and along the length of the tube to capture the pressure-time traces of the decompression wave. Tests were conducted for initial pressures of 33–37 MPa-a and a temperature range of 21–68°C. The experimentally determined decompression wave speeds were compared with both GASDECOM and PIPEDECOM predictions with and without nonequilibrium condensation delays at phase crossing. The interception points of the isentropes representing the decompression process with the corresponding phase envelope of each mixture were correlated with the respective plateaus observed in the decompression wave speed profiles. Additionally, speeds of sound in the undisturbed gas mixtures at the initial pressures and temperatures were compared with predictions by five equations of state, namely, BWRS, AGA-8, Peng–Robinson, Soave–Redlich–Kwong, and Groupe Européen de Recherches Gaziéres. The measured gas decompression curves were used to predict the fracture arrest toughness needed to assure fracture control in natural gas pipelines. The rupture tube test results have shown that the Charpy fracture arrest values predicted using GASEDCOM are within +7% (conservative) and −11% (nonconservative) of the rupture tube predicted values. Similarly, PIPEDECOM with no temperature delay provides fracture arrest values that are within +13% and −20% of the rupture tube predicted values, while PIPEDECOM with a 1°C temperature delay provides fracture arrest values that are within 0% and −20% of the rupture tube predicted values. Ideally, it would be better if the predicted values by the equations of state were above the rupture tube predicted values to make the predictions conservative but that was not always the case.


2019 ◽  
Vol 44 (14) ◽  
pp. 7428-7437 ◽  
Author(s):  
Bin Liu ◽  
Xiong Liu ◽  
Cheng Lu ◽  
Ajit Godbole ◽  
Guillaume Michal ◽  
...  

Author(s):  
Bob Eiber ◽  
Lorne Carlson ◽  
Brian Leis

This paper reviews the fracture control plan for the Alliance Pipeline, which is planned for operation in 2000. This natural-gas pipeline is 2627 km (1858 miles) long, running from British Columbia, Canada to Illinois, USA. Interest in the fracture control for this pipeline results from its design, which is based on transporting a rich natural gas (up to 15% ethane, 3% propane) at a relatively high pressure 12,000 kPa (1740 psi). This break from traditional pressures and lean gases, which frequently are constrained by incremental expansion, is more efficient and more economical than previous natural gas pipelines. Use of higher pressures and rich gas requires adequate fracture control for the line pipe, fittings, and valves. This fracture control has been achieved for the Alliance Pipeline by specifying high-toughness steels, in terms of both fracture-initiation and fracture-propagation resistance for the line pipe, fittings and heavy wall components. While beneficial from an economics viewpoint, the need for higher toughnesses raised concern over the validity of the fracture control plan, which was based on existing and new technology. The concern focused on fracture arrest using high toughness steels. The concern was associated with characterizing fracture arrest resistance using Charpy V-notch impact toughness, the most commonly used method to measure fracture arrest resistance. Developments were undertaken to address problems associated with the use of higher-toughness steel and these were validated with full-scale pipe burst tests to demonstrate the viability of the fracture control plan. The solution involved extending existing methods to address much higher toughness steels, which provided a significantly improved correlation between fracture arrest predictions and experimental results. In the burst tests, data was collected to validate the Alliance design and also to extend the database of fracture arrest data to assist future pipelines. Data such as the pressure between the pipe and soil as the gas escapes from the pipe, the sound levels in the atmosphere, the movement and strains in the pipe ahead of the running fracture were instrumented in the test and the available results are presented.


Author(s):  
K. K. Botros ◽  
S. Igi ◽  
J. Kondo

The Battelle two-curve method is widely used throughout the industry to determine the required material toughness to arrest ductile (or tearing) pipe fracture. The method relies on accurate determination of the propagation speed of the decompression wave into the pipeline once the pipe ruptures. GASDECOM is typically used for calculating this speed, and idealizes the decompression process as isentropic and one-dimensional. While GASDECOM was initially validated against quite a range of gas compositions and initial pressure and temperature, it was not developed for mixtures containing hydrogen. Two shock tube tests were conducted to experimentally determine the decompression wave speed in lean natural gas mixtures containing hydrogen. The first test had hydrogen concentration of 2.88% (mole) while the second had hydrogen concentration of 8.28% (mole). The experimentally determined decompression wave speeds from the two tests were found to be very close to each other despite the relatively vast difference in the hydrogen concentrations for the two tests. It was also shown that the predictions of the decompression wave speed using the GERG-2008 equation of state agreed very well with that obtained from the shock tube measurements. It was concluded that there is no effects of the hydrogen concentration (between 0–10% mole) on the decompression wave speed, particularly at the lower part (towards the choked pressure) of the decompression wave speed curve.


2010 ◽  
Author(s):  
Farshad Tabasinejad ◽  
Robert Gordon Moore ◽  
Sudarshan A. Mehta ◽  
Kees Cornelius Van Fraassen ◽  
Yalda Barzin ◽  
...  

2020 ◽  
Vol 221 ◽  
pp. 364-370
Author(s):  
Jiankun Shao ◽  
Alison M. Ferris ◽  
Rishav Choudhary ◽  
Séan J. Cassady ◽  
David F. Davidson ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document