scholarly journals Hybrid Multimodal Registration of Carotid Magnetic Resonance and Ultrasound Images Using Free-Form Deformation

Author(s):  
Anupama Gupta ◽  
Harsh K. Verma ◽  
Savita Gupta
2017 ◽  
Vol 16 (3) ◽  
pp. 373-381 ◽  
Author(s):  
Sara Broggi ◽  
Elisa Scalco ◽  
Maria Luisa Belli ◽  
Gerlinde Logghe ◽  
Dirk Verellen ◽  
...  

Purpose: To validate and compare the deformable image registration and parotid contour propagation process for head and neck magnetic resonance imaging in patients treated with radiotherapy using 3 different approaches—the commercial MIM, the open-source Elastix software, and an optimized version of it. Materials and Methods: Twelve patients with head and neck cancer previously treated with radiotherapy were considered. Deformable image registration and parotid contour propagation were evaluated by considering the magnetic resonance images acquired before and after the end of the treatment. Deformable image registration, based on free-form deformation method, and contour propagation available on MIM were compared to Elastix. Two different contour propagation approaches were implemented for Elastix software, a conventional one (DIR_Trx) and an optimized homemade version, based on mesh deformation (DIR_Mesh). The accuracy of these 3 approaches was estimated by comparing propagated to manual contours in terms of average symmetric distance, maximum symmetric distance, Dice similarity coefficient, sensitivity, and inclusiveness. Results: A good agreement was generally found between the manual contours and the propagated ones, without differences among the 3 methods; in few critical cases with complex deformations, DIR_Mesh proved to be more accurate, having the lowest values of average symmetric distance and maximum symmetric distance and the highest value of Dice similarity coefficient, although nonsignificant. The average propagation errors with respect to the reference contours are lower than the voxel diagonal (2 mm), and Dice similarity coefficient is around 0.8 for all 3 methods. Conclusion: The 3 free-form deformation approaches were not significantly different in terms of deformable image registration accuracy and can be safely adopted for the registration and parotid contour propagation during radiotherapy on magnetic resonance imaging. More optimized approaches (as DIR_Mesh) could be preferable for critical deformations.


Author(s):  
Stavros N. Leloudas ◽  
Giorgos A. Strofylas ◽  
Ioannis K. Nikolos

Given the importance of structural integrity of aerodynamic shapes, the necessity of including a cross-sectional area equality constraint among other geometrical and aerodynamic ones arises during the optimization process of an airfoil. In this work an airfoil optimization scheme is presented, based on Area-Preserving Free-Form Deformation (AP FFD), which serves as an alternative technique for the fulfillment of a cross-sectional area equality constraint. The AP FFD is based on the idea of solving an area correction problem, where a minimum possible offset is applied on all free-to-move control points of the FFD lattice, subject to the area preservation constraint. Due to the linearity of the area constraint in each axis, the extraction of an inexpensive closed-form solution to the area preservation problem is possible by using Lagrange Multipliers. A parallel Differential Evolution (DE) algorithm serves as the optimizer, assisted by two Artificial Neural Networks as surrogates. The use of multiple surrogate models, in conjunction with the inexpensive solution to the area correction problem, render the optimization process time efficient. The application of the proposed methodology for wind turbine airfoil optimization demonstrates its applicability and effectiveness.


2013 ◽  
Vol 60 (3) ◽  
pp. 537-563 ◽  
Author(s):  
Francesco Ballarin ◽  
Andrea Manzoni ◽  
Gianluigi Rozza ◽  
Sandro Salsa

Author(s):  
Vincent Cheutet ◽  
Jean-Philippe Pernot ◽  
Jean-Claude Leon ◽  
Bianca Falcidieno ◽  
Franca Giannini

To limit low-level manipulations of free-form surfaces, the concept of Fully Free Form Deformation Features (δ-F4) have been introduced. They correspond to shapes obtained by deformation of a surface area according to specified geometric constraints. In our work, we mainly focused on those features aimed at enforcing the visual effect of the so-called character lines, extensively used by designers to specify the shape of an object. Therefore, in the proposed approach, 3D lines are used to drive surface deformation over specified areas. Depending on the wished shape and reflection light effects, the insertion of character lines may generate surface tangency discontinuities. In CAD systems, such kind of discontinuities is generally created by a decomposition of the initial surface into several patches. This process can be tedious and very complex, depending on the shape of the deformation area and the desired surface continuity. Here, a method is proposed to create discontinuities on a surface, using the trimming properties of surfaces. The corresponding deformation features produce the resulting surface in a single modification step and handle simultaneously more constraints than current CAD systems. The principle of the proposed approach is based on arbitrary shaped discontinuities in the parameter domain of the surface to allow the surface exhibiting geometric discontinuities at user-prescribed points or along lines. The proposed approach is illustrated with examples obtained using our prototype software.


2011 ◽  
Vol 5 (4) ◽  
pp. 341 ◽  
Author(s):  
S. Jung ◽  
M. Hong ◽  
M.-H. Choi

Sign in / Sign up

Export Citation Format

Share Document