Mesh-based and polycapillary optics-based x-ray phase imaging

Author(s):  
Carolyn A. MacDonald ◽  
Weiyuan Sun ◽  
Congxiao He ◽  
Jonathan C. Petruccelli
2018 ◽  
Author(s):  
Jonathan C. Petruccelli ◽  
Weiyuan Sun ◽  
Carolyn A. MacDonald

2004 ◽  
Author(s):  
Timm Weitkamp ◽  
Ana Diaz ◽  
Bernd Nohammer ◽  
Franz Pfeiffer ◽  
Torben Rohbeck ◽  
...  

2005 ◽  
Author(s):  
Dariush Hampai ◽  
Sultan B. Dabagov ◽  
Giorgio Cappuccio ◽  
Giannantonio Cibin

Author(s):  
Uttam Pyakurel ◽  
Desiree D'Moore ◽  
Pikting Cheung ◽  
Bushra Kanwal ◽  
Xiaoyun Zhang ◽  
...  

2015 ◽  
Vol 60 (4) ◽  
pp. 2715-2720
Author(s):  
P. Zygoń ◽  
M. Gwoździk ◽  
J. Peszke ◽  
Z. Nitkiewicz

The paper presents properties of polymer composites reinforced with carbon nanotubes (CNT) containing various mixtures of dispersion. Acrylates of different particle size and viscosity were used to produce composites. The mechanical strength of composites was determined by three-point bending tests. The roughness parameter of composites was determined with a profilometer and compared with the roughness parameter determined via atomic force microscopy (AFM). Also X-ray studies (phase composition analysis, crystallite sizes determination) were carried out on these composites. Measurements of the surface topography using the Tapping Mode method were performed, acquiring the data on the height and on the phase imaging. The change of intensity, crystallite size and half-value width of main reflections originating from carbon within the composites have been determined using the X-ray analysis. The density of each obtained composite was determined as well as the resistivity at room temperature. The density of composites is quite satisfactory and ranges from 0.27 to 0.35 g/cm3. Different composites vary not only in strength but also in density. Different properties were achieved by the use of various dispersions. Carbon nanotubes constituting the reinforcement for a polymer composite improve the mechanical properties and conductivity composite.


2021 ◽  
Vol 118 (3) ◽  
pp. e2019068118
Author(s):  
Yuan Hung Lo ◽  
Jihan Zhou ◽  
Arjun Rana ◽  
Drew Morrill ◽  
Christian Gentry ◽  
...  

Biominerals such as seashells, coral skeletons, bone, and tooth enamel are optically anisotropic crystalline materials with unique nanoscale and microscale organization that translates into exceptional macroscopic mechanical properties, providing inspiration for engineering new and superior biomimetic structures. Using Seriatopora aculeata coral skeleton as a model, here, we experimentally demonstrate X-ray linear dichroic ptychography and map the c-axis orientations of the aragonite (CaCO3) crystals. Linear dichroic phase imaging at the oxygen K-edge energy shows strong polarization-dependent contrast and reveals the presence of both narrow (<35°) and wide (>35°) c-axis angular spread in the coral samples. These X-ray ptychography results are corroborated by four-dimensional (4D) scanning transmission electron microscopy (STEM) on the same samples. Evidence of co-oriented, but disconnected, corallite subdomains indicates jagged crystal boundaries consistent with formation by amorphous nanoparticle attachment. We expect that the combination of X-ray linear dichroic ptychography and 4D STEM could be an important multimodal tool to study nano-crystallites, interfaces, nucleation, and mineral growth of optically anisotropic materials at multiple length scales.


2020 ◽  
Vol 79 ◽  
pp. 93-102 ◽  
Author(s):  
Atsushi Momose
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document