scholarly journals Finite-Difference Time Domain Techniques Applied to Electromagnetic Wave Interactions with Inhomogeneous Plasma Structures

2018 ◽  
Vol 2018 ◽  
pp. 1-20 ◽  
Author(s):  
Julio L. Nicolini ◽  
José Ricardo Bergmann

Motivated by the emerging field of plasma antennas, electromagnetic wave propagation in and scattering by inhomogeneous plasma structures are studied through finite-difference time domain (FDTD) techniques. These techniques have been widely used in the past to study propagation near or through the ionosphere, and their extension to plasma devices such as antenna elements is a natural development. Simulation results in this work are validated with comparisons to solutions obtained by eigenfunction expansion techniques well supported by the literature and are shown to have an excellent agreement. The advantages of using FDTD simulations for this type of investigation are also outlined; in particular, FDTD simulations allow for field solutions to be developed at lower computational cost and greater resolution than equivalent eigenfunction methods for inhomogeneous plasmas and are applicable to arbitrary plasma properties such as spatially or time-varying inhomogeneities and collision frequencies, as well as allowing transient effects to be studied as the field solutions are obtained in the time domain.

1996 ◽  
Vol 430 ◽  
Author(s):  
Mikel J White ◽  
Steven F. Dillon ◽  
Magdy F. Iskander ◽  
Hal D. Kimrey

AbstractThere have been recent indications that variable-frequency microwave sintering of ceramics provides several advantages over single-frequency sintering, including more uniform heating, particularly for larger samples. The Finite-Difference Time-Domain (FDTD) code at the University of Utah was modified and used to simulate microwave sintering using variable frequencies and was coupled with a heat-transfer code to provide a dynamic simulation of this new microwave sintering process. This paper summarizes results from the FDTD simulations of sintering in a variable-frequency cavity. FDTD simulations were run in 100-MHz steps to account for the frequency variation in the electromagnetic fields in the multimode cavity. It is shown that a variable-frequency system does improve the heating uniformity when the proper frequency range is chosen. Specifically, for a single ceramic sample (4 × 4 × 6 cm3), and for a variable-frequency range from f = 2.5 GHz to f = 3.2 GHz, the temperature distribution pattern was much more uniform than the heating pattern achieved when using a single-frequency sintering system at f = 2.45 GHz.


2021 ◽  
Vol 35 (11) ◽  
pp. 1428-1429
Author(s):  
Madison Le ◽  
Mohammed Hadi ◽  
Atef Elsherbeni

Sub-gridding errors for a 2D Finite-Difference Time-Domain (FDTD) simulation are compared for both the standard FDTD and Hybrid higher order FDTD cases. Subgridding contrast ratios of 1:3, 1:9, 1:15, and 1:27 are considered and analyzed. A correlation is seen between the increase of contrast ratio with the increase of sub-gridding errors for both standard and hybrid cases. However, a trend of errors reduction when using hybrid formulations over standard formulations is apparent for each contrast ratio.


2014 ◽  
Vol 568-570 ◽  
pp. 1749-1752
Author(s):  
Bing Kang Chen ◽  
Feng Guo

In order to study the reflection of electromagnetic wave in Lorentz media, A finite-difference time-domain method based on the auxiliary differential equation (ADE) technique is used to obtain the formulation of 2-D TM wave propagation in lossy Lorentz media. In 1-D case, the reflected coefficients calculated by ADE-FDTD method and exact theoretical result are excellent agreement. This expresses that the 2-D formulas of electromagnetic wave propagation in lossy Lorentz media are right. Furthermore, Plane wave reflected by Lorentz media layer is calculated and simulated. Results display that reflected effect is evident.


Sign in / Sign up

Export Citation Format

Share Document