scholarly journals Hydrodynamic Performance of A-Jacks Concrete Armor Units in Riverbeds around Downstream in Flip Buckets

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Kamran Khalifehei ◽  
Gholamreza Azizyan ◽  
Mahmood Shafai-Bajestan
Keyword(s):  
Power Plants ◽  
Skin Friction Coefficient ◽  
Hydrodynamic Performance ◽  
Turbulence Energy ◽  
Reynolds Stresses ◽  
Free Jet ◽  
Bed Erosion ◽  
Reduction Methods ◽  
Flow Turbulence ◽  
The Impact

The jet flipped from flip buckets hits the dam’s downstream side as a free jet with an immense amount of energy, leading to bed erosion. Erosion of river bed materials downstream of dams could affect the performance of dams or power plants by altering the tailwater depth, rendering proper designs of controlling structures or erosion reduction methods highly indispensable in this regard. Hence, the hydrodynamic performance of A-Jacks concrete armor units in controlling scour was examined in this study. A-Jacks armors are applicable as a flexible protection without environmental risks often for bed erosion control. The desirable functionality of A-Jacks armors depends on the flow hydrodynamic parameters such as velocity profile variations ( U / U B ), the Reynolds stresses ( τ u ′ w ′ and τ v ′ w ′ ), and the skin friction coefficient ( C f ) created as a consequence of using A-Jacks armors on beds. The size of A-Jacks elements can have a role in increasing the flow turbulence to a certain depth so that after the impact of the flow with A-Jacks armor, the vortices’ intensity as well as the shear stress affecting the bed gradually decreases. The results of the numerical model suggest that the surge in the flow turbulence energy dissipation downstream of flip buckets significantly mitigates the underlying conditions of scouring phenomena, which is evidence of A-Jacks armors’ acceptable performance in scaling down scour depths.

scholarly journals Impact of the Wind Turbine on the Parameters of the Electricity Supply to an Agricultural Farm

2021 ◽  
Vol 13 (13) ◽  
pp. 7279
Author(s):  
Zbigniew Skibko ◽  
Magdalena Tymińska ◽  
Wacław Romaniuk ◽  
Andrzej Borusiewicz
Keyword(s):  
Power Plant ◽  
Wind Turbine ◽  
Wind Power ◽  
Rural Areas ◽  
Power Plants ◽  
Reactive Power ◽  
Supply Voltage ◽  
Common Source ◽  
Voltage Fluctuations ◽  
The Impact

Wind power plants are an increasingly common source of electricity located in rural areas. As a result of the high variability of wind power, and thus the generated power, these sources should be classified as unstable sources. In this paper, the authors attempted to determine the impact of wind turbine operation on the parameters of electricity supplied to farms located near the source. As a result of the conducted field tests, variability courses of the basic parameters describing the supply voltage were obtained. The influence of power plant variability on the values of voltage, frequency, and voltage distortion factor was determined. To estimate the capacity of the transmission lines, the reactive power produced in the power plant and its effect on the value of the power factor were determined. The conducted research and analysis showed that the wind power plant significantly influences voltage fluctuations in its immediate vicinity (the maximum value registered was close to 2%, while the value required by law was 2.5%). Although all the recorded values are within limits specified by the current regulations (e.g., the THD value is four times lower than the required value), wind turbines may cause incorrect operation of loads connected nearby. This applies mainly to cases where consumers sensitive to voltage fluctuations are installed in the direct vicinity of the power plant.

Overview of EAF Screening Results on the 900 MWe NPP French Fleet

2016 ◽  
Author(s):  
Thomas Métais ◽  
Nicolas Robert ◽  
Pierre Genette ◽  
Nicolas Etchegaray
Keyword(s):  
Power Plants ◽  
Screening Method ◽  
Experimental Tests ◽  
Degradation Process ◽  
Primary System ◽  
Transfer Coefficients ◽  
Screening Process ◽  
The Usa ◽  
License Renewal ◽  
The Impact

In the wake of numerous experimental tests carried out in air and also in a PWR environment, both abroad and in France, an update of the current thermal fatigue codification is underway in France. Proposals are currently being integrated in the RCC-M code [1]. In parallel, it is necessary to evaluate the impact of codification evolution on the RCS components. In the USA, such evaluations have already been implemented for license renewal to operate power plants beyond their initial 40 years of operation. In order to reduce the scope of the calculations to perform, a preliminary screening was carried out on the various areas of the primary system components: this screening is detailed in an EPRI report [2]. The output of this screening process is a list of locations that are most prone to EAF degradation process and it is on these zones only that detailed EAF calculations are carried out. In France, a similar approach was defined in the perspective of the fourth ten-year visit of the 900 MWe plants (VD4 900 MWe) so as to map out all the locations that are most impacted by EAF and hence concentrate the calculation effort on these specific areas for the VD4 900 MWe. In that respect, a specific methodology to evaluate the factor to account for environmental effects or Fen [3] based on correlations [4] for hot and cold shocks was established. These correlations use data that is readily accessible in transient description documents and stress reports such as temperature change, heat transfer coefficients, ramp duration and geometry. The need for these correlations is specific to the French context due to a need for a preliminary and yet precise idea of the overall impact of the modifications brought to the RCC-M code in fatigue before the VD4 900 MWe. This paper presents the results of the screening method that was applied to the whole RCS of the 900 MWe NPP fleet.

Sign in / Sign up

Export Citation Format

Share Document