Effects of periodic wakes on boundary layer development on an ultra-high-lift low pressure turbine airfoil

2016 ◽  
Vol 231 (1) ◽  
pp. 25-38 ◽  
Author(s):  
Xingen Lu ◽  
Yanfeng Zhang ◽  
Wei Li ◽  
Shuzhen Hu ◽  
Junqiang Zhu
Keyword(s):  
Boundary Layer ◽  
Transition Process ◽  
Low Pressure ◽  
Suction Surface ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Turbulent Transition ◽  
Boundary Layer Development ◽  
Unsteady Wake ◽  
Layer Development

The laminar-turbulent transition process in the boundary layer is of significant practical interest because the behavior of this boundary layer largely determines the overall efficiency of a low pressure turbine. This article presents complementary experimental and computational studies of the boundary layer development on an ultra-high-lift low pressure turbine airfoil under periodically unsteady incoming flow conditions. Particular emphasis is placed on the influence of the periodic wake on the laminar-turbulent transition process on the blade suction surface. The measurements were distinctive in that a closely spaced array of hot-film sensors allowed a very detailed examination of the suction surface boundary layer behavior. Measurements were made in a low-speed linear cascade facility at a freestream turbulence intensity level of 1.5%, a reduced frequency of 1.28, a flow coefficient of 0.70, and Reynolds numbers of 50,000 and 100,000, based on the cascade inlet velocity and the airfoil axial chord length. Experimental data were supplemented with numerical predictions from a commercially available Computational Fluid Dynamics code. The wake had a significant influence on the boundary layer of the ultra-high-lift low pressure turbine blade. Both the wake’s high turbulence and the negative jet behavior of the wake dominated the interaction between the unsteady wake and the separated boundary layer on the suction surface of the ultra-high-lift low pressure turbine airfoil. The upstream unsteady wake segments convecting through the blade passage behaved as a negative jet, with the highest turbulence occurring above the suction surface around the wake center. Transition of the unsteady boundary layer on the blade suction surface was initiated by the wake turbulence. The incoming wakes promoted transition onset upstream, which led to a periodic suppression of the separation bubble. The loss reduction was a compromise between the positive effect of the separation reduction and the negative effect of the larger turbulent-wetted area after reattachment due to the earlier boundary layer transition caused by the unsteady wakes. It appeared that the successful application of ultra-high-lift low pressure turbine blades required additional loss reduction mechanisms other than “simple” wake-blade interaction.

Effects of Reynolds Number and Freestream Turbulence Intensity on the Unsteady Boundary Layer Development on an Ultra-High-Lift Low Pressure Turbine Airfoil

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
Xue Feng Zhang ◽  
Howard Hodson
Keyword(s):  
Boundary Layer ◽  
Reynolds Numbers ◽  
Freestream Turbulence ◽  
Unsteady Boundary Layer ◽  
Suction Surface ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Boundary Layer Development ◽  
Unsteady Wake ◽  
Layer Development

The effects of Reynolds numbers and the freestream turbulence intensities (FSTIs) on the unsteady boundary layer development on an ultra-high-lift low-pressure turbine airfoil, so-called T106C, are investigated. The measurements were carried out at both Tu=0.5% and 4.0% within a range of Reynolds numbers, based on the blade chord and the isentropic exit velocity, between 100,000 and 260,000. The interaction between the unsteady wake and the boundary layer depends on both the strength of the wake and the status of the boundary layer. At Tu=0.5%, both the wake’s high turbulence and the negative jet behavior of the wake dominate the interaction between the unsteady wake and the separated boundary layer on the suction surface of the airfoil. Since the wake turbulence cannot induce transition before separation on this ultra-high-lift blade, the negative jet of the wake has the opportunity to induce a rollup vortex. At Tu=4.0%, the time-mean separation on the suction surface is much smaller. With elevated FSTI, the turbulence in the wake just above the boundary layer is no longer distinguishable from the background turbulence level. The unsteady boundary layer transition is dominated by the wake’s negative jet induced boundary layer variation.

Experimental Study of the Effect of Periodic Unsteady Wake Flow on Boundary Layer Development, Separation, and Reattachment Along the Surface of a Low Pressure Turbine Blade

2004 ◽  
Vol 126 (4) ◽  
pp. 663-676 ◽  
Author(s):  
M. T. Schobeiri ◽  
B. O¨ztu¨rk
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Wake Flow ◽  
Suction Surface ◽  
Low Pressure Turbine ◽  
Reduced Frequency ◽  
Boundary Layer Development ◽  
Unsteady Wake ◽  
Unsteady Wake Flow ◽  
Layer Development

The paper experimentally studies the effects of periodic unsteady wake flow on boundary layer development, separation and reattachment along the suction surface of a low pressure turbine blade. The experimental investigations were performed on a large scale, subsonic unsteady turbine cascade research facility at the Turbomachinery Performance and Flow Research Laboratory (TPFL), Texas A&M University. The experiments were carried out at a Reynolds number of 110,000 (based on suction surface length and exit velocity) with a free-stream turbulence intensity of 1.9%. One steady and two different unsteady inlet flow conditions with the corresponding passing frequencies, wake velocities, and turbulence intensities were investigated. The reduced frequencies cover the entire operating range of LP turbines. In addition to the unsteady boundary layer measurements, blade surface measurements were performed at the same Reynolds number. The surface pressure measurements were also carried out at one steady and two periodic unsteady inlet flow conditions. The results presented in ensemble-averaged, and the contour plot forms help to understand the physics of the separation phenomenon under periodic unsteady wake flow. It was found that the suction surface displayed a strong separation bubble for these three different reduced frequencies. For each condition, the locations and the heights defining the separation bubble were determined by carefully analyzing and examining the pressure and the mean velocity profile data. The location of boundary layer separation was independent of the reduced frequency level. However, the extent of the separation was strongly dependent on the reduced frequency level. Once the unsteady wake started to penetrate into the separation bubble, the turbulent spot produced in the wake paths caused a reduction of the separation bubble height.

Experimental Study of the Effect of Periodic Unsteady Wake Flow on Boundary Layer Development, Separation, and Re-Attachment Along the Surface of a Low Pressure Turbine Blade

2004 ◽  
Author(s):  
M. T. Schobeiri ◽  
B. O¨ztu¨rk
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Wake Flow ◽  
Suction Surface ◽  
Low Pressure Turbine ◽  
Reduced Frequency ◽  
Boundary Layer Development ◽  
Unsteady Wake ◽  
Unsteady Wake Flow ◽  
Layer Development

The paper experimentally studies the effects of periodic unsteady wake flow on boundary layer development, separation and re-attachment along the suction surface of a low pressure turbine blade. The experimental investigations were performed on a large scale, subsonic unsteady turbine cascade research facility at Turbomachinery Performance and Flow Research Laboratory (TPFL), Texas A&M University. The experiments were carried out at a Reynolds number of 110,000 (based on suction surface length and exit velocity) with a free-stream turbulence intensity of 1.9%. One steady and two different unsteady inlet flow conditions with the corresponding passing frequencies, wake velocities, and turbulence intensities were investigated. The reduced frequencies cover the entire operating range of LP turbines. In addition to the unsteady boundary layer measurements, blade surface measurements were performed at the same Reynolds number. The surface pressure measurements were also carried out at one steady and two periodic unsteady inlet flow conditions. The results presented in ensemble-averaged, and the contour plot forms help to understand the physics of the separation phenomenon under periodic unsteady wake flow. It was found that the suction surface displayed a strong separation bubble for these three different reduced frequencies. For each condition, the locations and the heights defining the separation bubble were determined by carefully analyzing and examining the pressure and the mean velocity profile data. The location of boundary layer separation was independent of the reduced frequency level. However, the extent of the separation was strongly dependent on the reduced frequency level. Once the unsteady wake started to penetrate into the separation bubble, the turbulent spot produced in the wake paths caused a reduction of the separation bubble height.

The Influence of Mach Number on the Boundary Layer Development of High-Lift Low Pressure Turbine in Low Reynolds Number

2020 ◽  
Author(s):  
Wenhua Duan ◽  
Jian Liu ◽  
Weiyang Qiao
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Mach Number ◽  
Turbine Blade ◽  
Low Reynolds Number ◽  
Low Pressure ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Boundary Layer Development ◽  
Layer Development

Abstract A numerical analysis of the effect of Mach number on the boundary layer development and aerodynamic performance of a high-lift, after loaded low pressure turbine blade is presented in this paper. The turbine blade is designed for the GTF engine and works in a low Reynolds number, high Mach number environment. Three different isentropic exit Mach numbers (0.14, 0.87 and 1.17) are simulated by large eddy simulation method, while the Reynolds number based on the axial chord length of the blade and the exit flow velocity is kept the same (1 × 105). The condition Mais,2 = 0.14 represents the lowspeeed wind tunnel environment which is usually used in the low pressure turbine investigation. The condition Mais,2 = 0.87 represents the design point of the turbine blade. The condition Mais,2 = 1.17 represents the severe environment when the shock wave shows up. A comparison of the boundary layer development is made and the total pressure loss results from the boundary layer is discussed.

Generation and Development of Klebanoff Streaks in Low-Pressure Turbine Cascade Under Upstream Wakes

2020 ◽  
Author(s):  
Shuang Sun ◽  
Xingshuang Wu ◽  
Tianrong Tan ◽  
Canlin Zuo ◽  
Sirui Pan ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Wall Shear Stress ◽  
Separation Bubble ◽  
Transition Process ◽  
Low Pressure ◽  
Suction Surface ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Wall Shear

Abstract At low Reynolds numbers operating condition, the boundary layer of the high-lift low-pressure turbine (LPT) of aero-engines is prone to separate on the suction surface of the airfoil. The profile losses of the airfoil are largely governed by the size of the separation bubble and the transition process in the boundary layer. However, the wake-induced transition, the natural transition and the instability induced by the Klebanoff streaks complicate the transition process. The boundary layer on the suction surface of a high-lift LPT was investigated at Re = 50,000 with upstream wakes. The numerical simulation was performed with the CFX software using large eddy simulations (LES), and the experiment was performed on a linear cascade. In this study, the wake is divided into the wake center and the wake tail, the unsteady formation process of the streaks and the wall shear stress caused by the wake are analyzed. A new mechanism of generation and development of Klebanoff Streaks was presented to better understand the effect of the wake on the boundary layer. Moreover, it was found that after entering the blade passage, the wake center does not contact the blade but causes the wall shear stress of the front part on the suction surface to increase. However, it is not possible to form strong Klebanoff streaks at the leading edge of the blade by shear sheltering effect. Only the wake tail can form Klebanoff streaks when it contacts the blade.

Effects of Reynolds Number and Freestream Turbulence Intensity on the Unsteady Boundary Layer Development on an Ultra-High-Lift LPT Airfoil

2007 ◽  
Author(s):  
Xue Feng Zhang ◽  
Howard Hodson
Keyword(s):  
Boundary Layer ◽  
Reynolds Numbers ◽  
Boundary Layer Transition ◽  
Freestream Turbulence ◽  
Unsteady Boundary Layer ◽  
Suction Surface ◽  
High Lift ◽  
Boundary Layer Development ◽  
Unsteady Wake ◽  
Layer Development

The effects of Reynolds numbers and the freestream turbulence intensities (FSTI) on the unsteady boundary layer development on an ultra-high-lift low-pressure (LP) turbine airfoil, so-called T106C, are investigated. The measurements were carried out at both Tu = 0.5% and 4.0% within a range of Reynolds numbers, based on the blade chord and the isentropic exit velocity, between 100,000 and 260,000. The interaction between the unsteady wake and the boundary layer depends on both the strength of the wake and the status of the boundary layer. At Tu = 0.5%, both the wake’s high turbulence and the negative jet behaviour of the wake dominate the interaction between the unsteady wake and the separated boundary layer on the suction surface of the airfoil. Since the wake turbulence cannot induce transition before separation on this ultra-high-lift blade, the negative jet of the wake has the opportunity to induce a rollup vortex. At Tu = 4.0%, the time-mean separation on the suction surface is much smaller. With elevated FSTI, the turbulence in the wake just above the boundary layer is no longer distinguishable from the background turbulence level. The unsteady boundary layer transition is dominated by the wake’s negative jet induced boundary layer variation.

scholarly journals Effect of Reynolds Number and Periodic Unsteady Wake Flow Condition on Boundary Layer Development, Separation, and Intermittency Behavior Along the Suction Surface of a Low Pressure Turbine Blade

2005 ◽  
Vol 129 (1) ◽  
pp. 92-107 ◽  
Author(s):  
M. T. Schobeiri ◽  
B. Öztürk ◽  
David E. Ashpis
Keyword(s):  
Boundary Layer ◽  
Reynolds Numbers ◽  
Wake Flow ◽  
Suction Surface ◽  
Low Pressure Turbine ◽  
Boundary Layer Development ◽  
Unsteady Wake ◽  
Unsteady Wake Flow ◽  
Layer Development ◽  
Intermittency Analysis

The paper experimentally studies the effects of periodic unsteady wake flow and Reynolds number on boundary layer development, separation, reattachment, and the intermittency behavior along the suction surface of a low pressure turbine blade. Extensive unsteady boundary layer experiments were carried out at Reynolds numbers of 110,000 and 150,000 based on suction surface length and exit velocity. One steady and two different unsteady inlet flow conditions with the corresponding passing frequencies, wake velocities, and turbulence intensities were investigated. The analysis of the experimental data reveals details of boundary layer separation dynamics which is essential for understanding the physics of the separation phenomenon under periodic unsteady wake flow and different Reynolds numbers. To provide a complete picture of the transition process and separation dynamics, extensive intermittency analysis was conducted. Ensemble-averaged maximum and minimum intermittency functions were determined, leading to the relative intermittency function. In addition, the detailed intermittency analysis was aimed at answering the question as to whether the relative intermittency of a separated flow fulfills the universality criterion.

Sign in / Sign up

Export Citation Format

Share Document