Seismic Performance Evaluation of Intermediate Moment Frames with Reduced Beam Section and Bolted Web Connections

2015 ◽  
Vol 31 (2) ◽  
pp. 895-919 ◽  
Author(s):  
Sang Whan Han ◽  
Ki Hoon Moon ◽  
Seong-Hoon Hwang ◽  
Bozidar Stojadinovic
Keyword(s):  
Seismic Performance ◽  
Seismic Design ◽  
Moment Frames ◽  
Seismic Performance Evaluation ◽  
Reduced Beam Section ◽  
Rotation Capacity ◽  
Special Moment Frames ◽  
Story Drift ◽  
Beam Section ◽  
B Test

A reduced beam section with a bolted web (RBS-B) connection is permitted for use only in intermediate moment frames (IMF) according to the ANSI/AISC 358-05. This is because some RBS-B test specimens failed to achieve 4% total rotation capacity, which is the minimum story drift angle required for special moment frames (SMF). Several studies reported that some RBS-B connections could experience brittle connection fracture during earthquakes, which can also be detrimental to the seismic performance of IMF systems with RBS-B connections. For investigating whether IMFs with RBS-B connections provide a satisfactory seismic performance, this study evaluated the seismic performance of IMFs with pre-qualified RBS-B connections following the ATC-63 procedure. Twenty-four model buildings were designed according to current seismic design provisions. Several IMFs with RBS-B connections do not satisfy the acceptance criteria specified in ATC-63.

Seismic Performance Evaluation of Steel Ordinary Moment Frames

2018 ◽  
Vol 34 (1) ◽  
pp. 55-76 ◽  
Author(s):  
Sang Whan Han ◽  
Tae O Kim ◽  
Seong Jin Baek
Keyword(s):  
Performance Evaluation ◽  
Seismic Performance ◽  
Seismic Design ◽  
Moment Frames ◽  
American Institute ◽  
Wind Drift ◽  
Seismic Performance Evaluation ◽  
Weak Beam ◽  
Seismic Force ◽  
American Society

Steel ordinary moment frames (OMF) are seismic force-resisting systems that can be used in buildings. In current seismic design and detailing provisions, such as the American Society of Civil Engineers ASCE/SEI 7-10 (2010) , American Institute of Steel Construction ANSI/AISC 341-10 (2010), and ANSI/AISC 358-10 (2010) , less stringent design and detailing requirements are specified for steel OMFs compared with those for steel special- and intermediate-moment frames. The strong-column weak-beam (SC/WB) requirement is not enforced for steel OMF connections. In the present study, the seismic performance evaluation is conducted for steel OMFs designed according to current seismic design and detailing provisions considering different combinations of gravity, seismic, and wind loads, as well as wind drift limits. Based on the results of seismic performance evaluation, permissible structural heights for steel OMFs are also proposed.

Experimental Seismic Performance Evaluation of Unreinforced Brick Masonry Shear Walls

2015 ◽  
Vol 31 (1) ◽  
pp. 215-246 ◽  
Author(s):  
Mohammed Javed ◽  
Guido Magenes ◽  
Bashir Alam ◽  
Akhtar Naeem Khan ◽  
Qaisar Ali ◽  
...  
Keyword(s):  
Seismic Performance ◽  
Primary Source ◽  
Shear Walls ◽  
Brick Masonry ◽  
Stone Masonry ◽  
Masonry Buildings ◽  
Kashmir Earthquake ◽  
Equivalent Viscous Damping ◽  
Seismic Performance Evaluation ◽  
Story Drift

Unreinforced masonry buildings, constructed with stones or bricks, are common in the northern areas of Pakistan. In the October 2005 Kashmir earthquake, the seismic performance of stone masonry buildings was found to be poor, which was the primary source of fatalities. Unreinforced brick masonry (URBM) buildings, however, performed well even in severely jolted areas. The performance of URBM could have been much better if the affected buildings were constructed by using proper guidelines. Taking lessons from the disaster, an experimental investigation, based on typical geometry and precompression levels of the URBM shear walls in the affected region, was conducted to evaluate their seismic performance. Twelve walls were tested in the in-plane direction using quasi-static cyclic loading. First-story drift ratios for various performance levels in URBM buildings are proposed. The influences of relative precompression level and aspect ratio on the damage pattern, ultimate drift ratio, and equivalent viscous damping of the walls are examined.

Seismic performance of composite RCS special moment frames

2013 ◽  
Vol 17 (2) ◽  
pp. 450-457 ◽  
Author(s):  
Bahman Farahmand Azar ◽  
Hosein Ghaffarzadeh ◽  
Nima Talebian
Keyword(s):  
Seismic Performance ◽  
Moment Frames ◽  
Special Moment Frames
Sign in / Sign up

Export Citation Format

Share Document