scholarly journals Determination of the Neutron Beam Spatial Profile at n_TOF EAR-2 using the CR-39 Track Detectors

2019 ◽  
Vol 23 ◽  
pp. 28
Author(s):  
Z. Eleme ◽  
M. Alexandropoulou ◽  
A. Georgiadou ◽  
K. G. Ioannides ◽  
M. Kokkoris ◽  
...  
Keyword(s):  
Neutron Beam ◽  
Optical Microscope ◽  
Fast Neutrons ◽  
Hydrogen Atoms ◽  
Spatial Profile ◽  
Naoh Solution ◽  
Sample Position ◽  
Cr 39 Detectors

Within the present work the neutron beam spatial profile was determined at the sample position in EAR-2 at the n_TOF facility at CERN. The CR-39 detectors were coupled with a 2mm PE foil serving as neutron-to-proton converter. Two irradiations were performed in the 10x5 cm surface of CR-39 detectors. Proton tracks were revealed in the CR-39 detectors resulting from the elastic scattering of fast neutrons on the hydrogen atoms in the PE converter. Afterwards, the CR-39 detectors were chemically etched in aqueous NaOH solution and latent tracks were considerably enlarged to become visible under an optical microscope. After the scanning of the detectors surface, the acquired images were analyzed using the ImageJ program. In the present work, the experimental setup and procedure will be presented along with the results concerning the characterization of the neutron beam spatial profile at the sample position in the n_TOF EAR-2.

CHARACTERIZATION OF THE SINTERED Nd15Fe77B8 ALLOY

2011 ◽  
Vol 25 (06) ◽  
pp. 877-884
Author(s):  
L. HADJADJ
Keyword(s):  
Heat Treatment ◽  
Magnetic Properties ◽  
Optical Microscope ◽  
The Other ◽  
Average Value ◽  
Nd15fe77b8 Alloy

In this work the purpose is, in addition to the determination of microhardness, to get some information about the effect of heat treatment on the microstructure of the magnetic Nd 15 Fe 77 B 8 alloy. For this study we have used an optical microscope and an electronic microprobe. The results show that the structure of the Nd 2 Fe 14 B phase, which confers good mechanical and magnetic properties on the alloy, is well tetragonal, as mentioned in several works. The morphology, the concentration and the quantity of this phase depend on the temperature of annealing. The microhardness of the phase has an average value between those of the other involved phases.

scholarly journals ANALYSIS OF PARTICLE DISTRIBUTION IN A DOUBLE LAYER BEAM SHAPING ASSEMBLY RESULTED FROM 30 MEV-PROTON REACTIONS WITH BERYLLIUM TARGET USING THE PHITS PROGRAM

2020 ◽  
Vol 82 (3) ◽  
Author(s):  
Bilalodin Bilalodin ◽  
Gede Bayu Suparta ◽  
Arief Hermanto ◽  
Dwi Satya Palupi ◽  
Yohannes Sardjono ◽  
...  
Keyword(s):  
Double Layer ◽  
Neutron Beam ◽  
Particle Flux ◽  
Epithermal Neutron ◽  
Beam Shaping ◽  
Fast Neutrons ◽  
Hydrogen Atoms ◽  
Epithermal Neutrons ◽  
Beryllium Target ◽  
Beam Shaping Assembly

An analysis on the distribution of particle flux emanating from reactions of 30 MeV-proton with beryllium target in a double layer beam shaping assembly (BSA) has been carried out using the PHITS program.  It studies important parameters relating to the distribution of proton, neutron, and gamma. It is revealed that reactions of proton and beryllium in double layer BSA produce fast neutrons and other protons, resulting from certain reactions, and recoil protons from the interactions of fast neutrons and hydrogen atoms. Fast neutrons are distributed around beryllium target, moderator, reflector, and collimator. They are moderated by Al and LiF material. Epithermal neutrons spread along the moderator, with a distribution that is tapering down as it approaches the end of the collimator (aperture). During its travel along the moderator, an epithermal neutron decreases in energy to become a thermal neutron. The spectrum of neutron beam produced by the double layer BSA is wide, which indicates that the neutron beam exiting the aperture consists of three kinds of neutrons, dominated by epithermal neutronswith energy range 1 eV – 10 keV.  

Characterization of Impressed Current Technique to Model Corrosion of Reinforcement in Concrete

2020 ◽  
Vol 11 (1) ◽  
pp. 93-99
Author(s):  
Abu Zakir Morshed ◽  
Sheikh Shakib ◽  
Tanzim Jahin
Keyword(s):  
Immersion Time ◽  
Chloride Content ◽  
Engineering Science ◽  
Coastal Regions ◽  
Faraday’S Law ◽  
Current Technique ◽  
Corrosion Cell ◽  
Impressed Current

Corrosion of reinforcement is an important durability concern for the structures exposed to coastal regions. Since corrosion of reinforcement involves long periods of time, impressed current technique is usually used to accelerate the corrosion of reinforcement in laboratories. Characterization of impressed current technique was the main focus of this research,which involved determination of optimum chloride content and minimum immersion time of specimens for which the application of Faraday’s law could be efficient. To obtain optimum chloride content, the electrolytes in the corrosion cell were prepared similar to that of concrete pore solutions. Concrete prisms of 200 mm by 200 mm by 300 mm were used to determine the minimum immersion time for saturation. It was found that the optimum chloride content was 35 gm/L and the minimum immersion time for saturation was 140 hours. Accounting the results, a modified expression based on Faraday’s law was proposed to calculate weight loss due to corrosion. Journal of Engineering Science 11(1), 2020, 93-99

The Determination of Sense via Deleuze and Blanchot: Paradoxes of the Habitual, the Immemorial, and the Eternal Return

2008 ◽  
Vol 2 (2) ◽  
pp. 155-177 ◽  
Author(s):  
Eugene Brently Young
Keyword(s):  
Eternal Return

Eternal return is the paradox that accounts for the interplay between difference and repetition, a dynamic at the heart of Deleuze's philosophy, and Blanchot's approach to this paradox, even and especially through what it elides, further illuminates it. Deleuze draws on Blanchot's characterisations of difference, forgetting, and the unlivable to depict the ‘sense’ produced via eternal return, which, for Blanchot, is where repetition implicates or ‘carries’ pure difference. However, for Deleuze, difference and the unlivable are also developed by the living repetition or ‘contraction’ of habit, which results in his distinctive characterization of ‘force’, ‘levity’, and sense in eternal return.

SEM/EDS Characterization of Uncommon Metal Whiskers and Determination of Underlying Growth Mechanisms

2018 ◽  
Author(s):  
D. Basak ◽  
L. H. Ponce
Keyword(s):  
Reliability Analysis ◽  
Case Studies ◽  
Whisker Growth ◽  
Innovation Systems ◽  
Growth Mechanisms ◽  
Crystal Oscillator ◽  
Analysis Laboratory ◽  
Investigative Techniques

Abstract Two case-studies on uncommon metals whiskers, performed at the Reliability Analysis Laboratory (RAL) of Northrop Grumman Innovation Systems, are presented. The components analyzed are an Oven Controlled Crystal Oscillator (OCXO) and an Electromechanical Relay. Investigative techniques were used to determine the chemical and physical makeup of the metal whiskers and develop an understanding of the underlying effects and mechanisms that caused the conditions conducive to whisker growth.

Sign in / Sign up

Export Citation Format

Share Document