scholarly journals Description of Non-Stationary Heat Transfer in Two-Phase Polycrystalline Metal-Ceramic Composites

2015 ◽  
Vol 128 (4) ◽  
pp. 624-628 ◽  
Author(s):  
T. Sadowski ◽  
P. Golewski
Keyword(s):  
Heat Transfer ◽  
Ceramic Composites ◽  
Polycrystalline Metal ◽  
Two Phase ◽  
Stationary Heat ◽  
Metal Ceramic ◽  
Stationary Heat Transfer

SENSITIVITY ANALYSIS OF A STATIONARY HEAT TRANSFER TWO-PHASE LIQUID-GAS SLUG FLOW MODEL FOR HORIZONTAL PIPES

2015 ◽  
Author(s):  
Carlos L. Bassani ◽  
Fernando H. G. Pereira ◽  
Fausto A. A. Barbuto ◽  
Rigoberto E. M. Morales
Keyword(s):  
Heat Transfer ◽  
Sensitivity Analysis ◽  
Slug Flow ◽  
Flow Model ◽  
Two Phase ◽  
Horizontal Pipes ◽  
Stationary Heat ◽  
Phase Liquid ◽  
Stationary Heat Transfer

Heat Removal and Thermal Stabilization of High-temperature Surfaces by a Dispersed Coolant Flow

Vestnik MEI ◽  
2021 ◽  
pp. 19-26
Author(s):  
Valentin S. Shteling ◽  
◽  
Vladimir V. Ilyin ◽  
Aleksandr T. Komov ◽  
Petr P. Shcherbakov ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flux Density ◽  
Flow Rate ◽  
Heat Flux Density ◽  
Coolant Flow ◽  
Transfer Coefficients ◽  
Stationary Heat ◽  
Heat Transfer Coefficients ◽  
Stationary Heat Transfer

The effectiveness of stabilizing the surface temperature by a dispersed coolant flow is experimentally studied on a bench simulating energy intensive elements of thermonuclear installations A test section in which the maximum heat flux density can be obtained when being subjected to high-frequency heating was developed, manufactured, and assembled. The test section was heated using a VCh-60AV HF generator with a frequency of not lower than 30 kHz. A hydraulic nozzle with a conical insert was used as the dispersing device. Techniques for carrying out an experiment on studying a stationary heat transfer regime and for calculating thermophysical quantities were developed. The experimental data were obtained in the stationary heat transfer regime with the following range of coolant operating parameters: water pressure equal to 0.38 MPa, water mass flow rate equal to 5.35 ml/s, and induction heating power equal to 6--19 kW. Based on the data obtained, the removed heat flux density and the heat transfer coefficients were calculated for each stationary heat transfer regime. The dependences of the heat transfer coefficient on the removed heat flux density and of the removed heat flux density on the temperature difference have been obtained. High values of heat transfer coefficients and heat flux density at a relatively low coolant flow rate were achieved in the experiments.

Non-stationary heat transfer beyond diffusion spinodal of a solution

2020 ◽  
Author(s):  
S. B. Rutin ◽  
P. V. Skripov ◽  
A. A. Igolnikov
Keyword(s):  
Heat Transfer ◽  
Stationary Heat ◽  
Stationary Heat Transfer

USE OF NUMERICAL MODELS FOR NON-STATIONARY HEAT TRANSFER COMPRESSION BETWEEN TWO MEDIA

2017 ◽  
Author(s):  
Daniel Tarrazó-Serrano ◽  
Sergio Castiñeira-Ibañez ◽  
José Tarrazó-Morell ◽  
Constanza Rubio-Michavila
Keyword(s):  
Heat Transfer ◽  
Numerical Models ◽  
Stationary Heat ◽  
Stationary Heat Transfer
Sign in / Sign up

Export Citation Format

Share Document