812 Analysis of the stress intensity factor in two-dimensional joints under shear load using an enriched finite element

2005 ◽  
Vol 2005.18 (0) ◽  
pp. 249-250
Author(s):  
Hideo KOGUCHI ◽  
Chonlada LUANGARPA ◽  
Monchai PRUKVILAILERT
Keyword(s):  
Stress Intensity Factor ◽  
Finite Element ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Shear Load ◽  
Two Dimensional ◽  
Enriched Finite Element

Computation of Stress Intensity Factor for Multiple Cracks Using Singular Finite Element

2011 ◽  
Vol 214 ◽  
pp. 75-79 ◽  
Author(s):  
Ruslizam Daud ◽  
Ahmad Kamal Ariffin ◽  
Shahrum Abdullah ◽  
Al Emran Ismail ◽  
A. Zulkifli
Keyword(s):  
Stress Intensity Factor ◽  
Finite Element ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Analytical Solution ◽  
Crack Width ◽  
Width Ratio ◽  
Multiple Cracks ◽  
Two Dimensional ◽  
Interval Ratio

The simplification of two dimensional approaches in singular finite elements has promoted the method to be used in the formulation of stress intensity factor (SIF) of multiple cracks in finite body. The effect of shielding and amplification are considered in defining the SIF. As been observed, the current available analytical approximations are more restricted to several assumptions. The more accurate and less restricted method has motivated this study. This paper presents the investigation of singular finite elements applied in two dimensional finite element models subjected to different crack-width ratio and cracks interval ratio. The newly finite element formulations are resulted with good agreement with theoretical statement compared to analytical solution. The weak points of presented analytical solution are discussed regards to the influence of crack width ratio and cracks interval ratio.

Stress Intensity Factors for Unequal Longitudinal-Radial Cracks in Thick-Walled Cylinders

1991 ◽  
Vol 113 (1) ◽  
pp. 22-27 ◽  
Author(s):  
J. L. Desjardins ◽  
D. J. Burns ◽  
R. Bell ◽  
J. C. Thompson
Keyword(s):  
Stress Intensity Factor ◽  
Finite Element ◽  
Stress Intensity ◽  
Finite Elements ◽  
Intensity Factor ◽  
Stress Intensity Factors ◽  
Two Dimensional ◽  
Intensity Factors ◽  
Radial Cracks ◽  
Good Agreement

Finite elements and two-dimensional photoelasticity have been used to analyze thick-walled cylinders which contain arrays of straight-fronted, longitudinal-radial cracks of unequal depth. The stress intensity factor K1 has been computed for the dominant crack and for some of the surrounding cracks. Cylinders with 2, 4, 6, 8, 16, 36 and 40 cracks have been considered. Good agreement has been obtained between the experimental and the numerical results and, for cylinders with 2 or 4 cracks, with previously published predictions. The results for all of the foregoing cases are used to develop simple, approximate techniques for estimating K1 for the dominant crack, when the total number of cracks is different from those that have been considered herein. Estimates of K1 obtained by these techniques agree well with corresponding finite element results.

Application of Extended Finite Element Method (XFEM) to Stress Intensity Factor Calculations

2015 ◽  
Author(s):  
Do-Jun Shim ◽  
Mohammed Uddin ◽  
Sureshkumar Kalyanam ◽  
Frederick Brust ◽  
Bruce Young
Keyword(s):  
Finite Element Method ◽  
Stress Intensity Factor ◽  
Finite Element ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Degrees Of Freedom ◽  
Extended Finite Element Method ◽  
Partition Of Unity ◽  
Extended Finite Element ◽  
Element Method

The extended finite element method (XFEM) is an extension of the conventional finite element method based on the concept of partition of unity. In this method, the presence of a crack is ensured by the special enriched functions in conjunction with additional degrees of freedom. This approach also removes the requirement for explicitly defining the crack front or specifying the virtual crack extension direction when evaluating the contour integral. In this paper, stress intensity factors (SIF) for various crack types in plates and pipes were calculated using the XFEM embedded in ABAQUS. These results were compared against handbook solutions, results from conventional finite element method, and results obtained from finite element alternating method (FEAM). Based on these results, applicability of the ABAQUS XFEM to stress intensity factor calculations was investigated. Discussions are provided on the advantages and limitations of the XFEM.

Sign in / Sign up

Export Citation Format

Share Document