Load-Carrying Capacity of Austempered Ductile Iron (ADI) Gears (Observation of tooth surface failure)

2003 ◽  
Vol 2003.4 (0) ◽  
pp. 27-28
Author(s):  
Ryohei ISHIMARU ◽  
Yasutsune ARIURA ◽  
Kotaro HIDAKA ◽  
Masahito GOKA
Keyword(s):  
Carrying Capacity ◽  
Ductile Iron ◽  
Austempered Ductile Iron ◽  
Tooth Surface ◽  
Load Carrying Capacity ◽  
Surface Failure ◽  
Load Carrying

704 Load-Carrying Capacity of Austempered Ductile Iron(ADI) Gears(Fine Particle Shot Peened ADI Gear)

2000 ◽  
Vol 005.2 (0) ◽  
pp. 207-208
Author(s):  
Ryohei ISHIMARU ◽  
Yasutsune ARIURA ◽  
Koichi YOSHIOKA ◽  
Kimihiro TANAKA ◽  
Masahito GOKA
Keyword(s):  
Carrying Capacity ◽  
Ductile Iron ◽  
Fine Particle ◽  
Austempered Ductile Iron ◽  
Load Carrying Capacity ◽  
Load Carrying

F-0331 Load-Carrying Capacity of Austempered Ductile Iron (ADI) Gears : Effect of Fine Particle Shot-Peening

2001 ◽  
Vol III.01.1 (0) ◽  
pp. 163-164
Author(s):  
Ryohei ISHIMARU ◽  
Yasutsune ARIURA ◽  
Koichi YOSHIOKA ◽  
Wataru TOMETAKA ◽  
Masahito GOKA
Keyword(s):  
Carrying Capacity ◽  
Ductile Iron ◽  
Shot Peening ◽  
Fine Particle ◽  
Austempered Ductile Iron ◽  
Load Carrying Capacity ◽  
Load Carrying

The Effects of Surface Roughening and Protective Film Formation on Scuff Initiation in Boundary Lubrication

1991 ◽  
Vol 113 (2) ◽  
pp. 295-302 ◽  
Author(s):  
Young-ze Lee ◽  
K. C. Ludema
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Carrying Capacity ◽  
Fluid Film ◽  
Surface Roughening ◽  
Protective Film ◽  
Load Carrying Capacity ◽  
Surface Failure ◽  
Load Carrying ◽  
Fluid Film Thickness

The mechanisms of failure of lubricated steel surfaces were investigated. The focus was on two phenomena, namely, the effects of lubricant reactivity and the effects of sliding speed. Experiments were performed with the ball-on-flat and the cylinder-on-flat geometries in the manner of the methods used to develop the failure maps of the (OECD) IRG. Contact resistance and coefficient of friction were measured during the tests and surface roughness was measured frequently during the tests. Surface failure could not be predicted by using the ratio λ (the ratio of fluid film thickness to composite surface roughness) except when chemically inert lubricants are used. Even then the adverse influence of temperature rise on fluid film thickness does not adequately explain the low load carrying capacity of lubricated surfaces at high sliding speeds. There is a separate effect, namely, a quicker and more severe surface roughening at high speeds than at low speeds, which causes surface failure. The protective layers on sliding surfaces that form by chemical reaction with the lubricant were found to reduce the surface roughening and increase the load carrying capacity of surfaces to values of λ as low as 0.03.

Sign in / Sign up

Export Citation Format

Share Document