scholarly journals An Investigation of Combustion Robustness of HCCI Engines at Retarded Combustion Phasing Operation : By Use of Numerical Analysis with Multi-Zone Model(Thermal Engineering)

2010 ◽  
Vol 76 (761) ◽  
pp. 142-148
Author(s):  
Kenji SHIGETOYO ◽  
Mari NAGAE ◽  
Hiroki IINO ◽  
Norimasa IIDA
2010 ◽  
Vol 76 (771) ◽  
pp. 1924-1931
Author(s):  
Takao KOSHIMIZU ◽  
Hiromi KUBOTA ◽  
Yasuyuki TAKATA ◽  
Takehiro ITO

Author(s):  
Iván D. Bedoya ◽  
Samveg Saxena ◽  
Francisco J. Cadavid ◽  
Robert W. Dibble

This study investigates the effects of biogas composition on combustion stability for a purely biogas fueled homogeneous charge compression ignition (HCCI) engine. Biogas is one of the most promising renewable fuels for combined heat and power systems driven by internal combustion engines. However, the high content of CO2 in biogas composition leads to low thermal efficiencies in spark ignited and dual fuel compression ignited engines. The study is divided into two parts: First experimental results on a biogas-fueled HCCI engine are used to illustrate the effects of intake conditions on combustion stability, and second a simulation methodology is used to investigate how biogas composition impacts combustion stability at constant intake conditions. Experimental analysis of a four cylinder, 1.9 L Volkswagen TDI diesel engine shows that biogas-HCCI combustion exhibits high gross indicated mean effective pressure (close to 8 bar), high gross indicated efficiency (close to 45%), and ultralow NOx emissions below the US2010 limit (0.27 g/kWh). An inlet absolute pressure of 2 bar and inlet temperature of 473 K (200 °C) were required for allowing HCCI combustion with a biogas composition of 60% CH4 and 40% CO2 on a volumetric basis. However, slight changes in inlet pressure and temperature caused large changes in cycle-to-cycle variations at low equivalence ratios and large changes in ringing intensity at high equivalence ratios. Numerical analysis of biogas-HCCI combustion is carried out with a sequential methodology that includes one-zone model simulations, computational fluid dynamics (CFD) analysis, and 12-zones model simulations. Numerical results for varied biogas composition show that at high load limit, higher contents of CH4 in biogas composition allow advanced combustion and increased burning rates of the biogas air mixture. Higher contents of CO2 in biogas composition allow lowered ringing intensities with moderate decrease in the indicated efficiency and power output. NOx emissions are not highly affected by biogas composition, while CO and unburned hydrocarbons (HC) emissions tend to increase with higher contents of CO2. According with the numerical results, biogas composition is an effective strategy to control the onset of combustion and combustion phasing of HCCI engines running biogas, allowing more stabilized combustion at low equivalence ratios and safe operation at high equivalence ratios. The main advantages of using biogas-fueled HCCI engines in CHP systems are the low sensitivity of power output and indicated efficiency to biogas composition, as well as the ultralow NOx emissions achieved for all tested compositions.


2018 ◽  
Vol 774 ◽  
pp. 84-89 ◽  
Author(s):  
Roman Vodička ◽  
Katarína Krajníková

A model for numerical analysis of interface damage which leads to interface crack initiationand propagation in multi-domain structures under cyclic loading is considered. Modelling of damagetakes into account various relations between interface stresses and displacement gaps providing theresponse of a cohesive zone model, additionally equipped by a kind of viscosity associated to theevolution of the interface damage. Together with repeating loading-unloading conditions, it makesthis damage process to have a fatigue-like character, where the crack appears for smaller magnitudeof the cyclic load than for pure uploading.


Author(s):  
Amanie N. Abdelmessih

Most thermal engineers will model and analyze thermal engineering cases, using any of the numerous thermal analysis software, available in the market. These commercial software need years of continuous use to be fully mastered. Large companies can afford to acquire expensive software available in the market and train their engineers; but small companies do not have the financial means to acquire such expensive software. Thus for modeling and analysis, small companies or private practice need a different alternative. Excel is one of the programs that come with Microsoft Office suite of software, which is installed on any purchased computer. Most users of Microsoft office are proficient in using Word, and can use Excel as a spread sheet to speed up calculations. Technical personnel can easily use the charting capability of Excel, but very few engineers can use Excel for intensive Numerical Analysis. Engineers should be able to use the available inexpensive Excel software to perform numerical analysis at their work place. In this article three Heat Transfer Numerical cases using Microsoft Excel are discussed in detail. the first case is two dimensional steady state heat transfer with different isothermal boundary conditions. The second shows other boundary conditions: uniform heat flux, adiabatic, and convection. The third case is transient conditions. The results from the three cases are compared with results from Patran Thermal software.


Sign in / Sign up

Export Citation Format

Share Document