Influence of Process Parameters And Tool On Mechanical And Metallurgical Properties of Pure Copper And Aluminum Alloy AA7075 Dissimilar Friction Stir Welded Joints

2021 ◽  
Vol 69 (9) ◽  
pp. 73-79
Author(s):  
Supraja Reddy B ◽  
Ram Gopal Reddy B
Keyword(s):  
Aluminum Alloy ◽  
Process Parameters ◽  
Welded Joints ◽  
Pure Copper ◽  
Influence Of Process Parameters ◽  
Friction Stir ◽  
Metallurgical Properties

Fabrication and characterization of friction stir processed Al 6061 reinforced with TiB2-Al2O3

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ch. Mohana Rao ◽  
K. Mallikarjuna Rao
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Practical Implication ◽  
Research Work ◽  
Influence Of Process Parameters ◽  
Volume Percentage ◽  
Content Type ◽  
Friction Stir

PurposeThe objective of the paper is to evaluate the fabrication process and to study the influence of process parameters of friction stir processing of 6061-TiB2-Al2O3 Aluminum alloy surface composite on microhardness tensile strength, and microstructure.Design/methodology/approachFriction stir processing method is used for attaining the desired mechanical properties, and selectively processed reinforcements to fabricate the samples. The Taguchi technique was used to optimize rotational speed, travel speed and volume percentage of reinforcement particles to enhance the mechanical properties of 6061-TiB2-Al2O3 Aluminum alloy composite.FindingsThe fabrication of surface composites through FSP allows new inventions in terms of material with enhanced surface layers without changing the base metal.Practical implicationsTo examine the behavior of the surface of the composites in the different zones, the practical implication consists of the use of different characterization techniques like optical microscopy and scanning microscopy for microstructural behavior and the measurement of hardness and tensile tests for mechanical behavior.Originality/valueThe research work consists of tool design and process parameters, which can affect the final product (microstructural changes), and the performance of the modified surface layer behavior was studied and presented.

scholarly journals Forming and Properties of Friction Stir Welding Process for Dissimilar Mg Alloy

2015 ◽  
Vol 9 (1) ◽  
pp. 859-864
Author(s):  
Tielong Li ◽  
Zhenshan Wang
Keyword(s):  
Magnesium Alloy ◽  
Process Parameters ◽  
Welded Joints ◽  
Defect Formation ◽  
Base Material ◽  
Welding Process ◽  
Fracture Initiation ◽  
Line Defect ◽  
Influence Of Process Parameters ◽  
Friction Stir

For hot extrusions of magnesium alloy sheets, Dissimilar AZ80 and AZ31 were used, in which AZ80 was placed on advancing side and AZ31 on retreating side, using friction stir butt welding with different process parameters. Some defect-free welded joints with good weld surfaces could be obtained with some suitable welding conditions. The maximum tensile strength of welded joint which is 225.5 MPa can reach 98% that of the AZ31 base material. Influence of process parameters on defects, weld shaping and mechanical property were discussed systematically. And the microstructure of different zones was compared. The fracture of the welded joints takes place at the junction of mechanical heat affected zone and nugget zone in AZ31 magnesium alloy set retreating side, since existing difference in metallographic structure of alloy diversely suffered by heat, pressure and depositing impurities. Fracture initiation site may be the P line defect which should be eliminated, and the P line defect formation was analyzed.

scholarly journals Influence of process parameters on mechanical properties of friction stir welded 5083-O aluminum alloy

2021 ◽  
Vol 18 ◽  
Author(s):  
Nicole Brum ◽  
Carla Amavisca ◽  
Jerônimo Ghisi Schroeder ◽  
Jonas Buzzatti ◽  
Guilherme Vieira Braga Lemos ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Process Parameters ◽  
Influence Of Process Parameters ◽  
Friction Stir

Microstructure and morphology evolution of probeless friction stir spot welded joints of aluminum alloy

2018 ◽  
Vol 252 ◽  
pp. 69-80 ◽  
Author(s):  
W.Y. Li ◽  
Q. Chu ◽  
X.W. Yang ◽  
J.J. Shen ◽  
A. Vairis ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Welded Joints ◽  
Morphology Evolution ◽  
Friction Stir ◽  
Spot Welded

scholarly journals Increasing of the Mechanical Properties of Friction Stir Welded Joints of 6061 Aluminum Alloy by Introducing Alumina Particles

2017 ◽  
Vol 17 (2) ◽  
pp. 29-40 ◽  
Author(s):  
M. A. Tashkandi ◽  
J. A. Al-Jarrah ◽  
M. Ibrahim
Keyword(s):  
Aluminum Alloy ◽  
Base Metal ◽  
Welded Joints ◽  
Volume Fraction ◽  
Welding Process ◽  
Welding Zone ◽  
6061 Aluminum Alloy ◽  
Friction Stir ◽  
Alumina Particles ◽  
Welding Line

AbstractThe main aim of this investigation is to produce a welding joint of higher strength than that of base metals. Composite welded joints were produced by friction stir welding process. 6061 aluminum alloy was used as a base metal and alumina particles added to welding zone to form metal matrix composites. The volume fraction of alumina particles incorporated in this study were 2, 4, 6, 8 and 10 vol% were added on both sides of welding line. Also, the alumina particles were pre-mixed with magnesium particles prior being added to the welding zone. Magnesium particles were used to enhance the bonding between the alumina particles and the matrix of 6061 aluminum alloy. Friction stir welded joints containing alumina particles were successfully obtained and it was observed that the strength of these joints was better than that of base metal. Experimental results showed that incorporating volume fraction of alumina particles up to 6 vol% into the welding zone led to higher strength of the composite welded joints as compared to plain welded joints.

Sign in / Sign up

Export Citation Format

Share Document