A Model of Enhanced Strain Rate Sensitivity in Nanocrystalline and Ultrafine-Grained Metals

2018 ◽  
Vol 57 (1) ◽  
pp. 1-10
Author(s):  
A.G. Sheinerman ◽  
S.V. Bobylev

Abstract A model is suggested that describes enhanced strain rate sensitivity of nanocrystalline and ultrafine-grained metals. Within the model, plastic deformation of such metals incorporates dislocation transmission across grain boundaries (GBs) in the stress fields of dislocation pileups, the emission of individual dislocations from GBs as well as GB sliding accommodated by GB dislocation climb and/or Coble creep. The model predicts a strong increase in the strain rate sensitivity and a decrease in the activation volume with decreasing grain size, in accord with experimental data.We also considered the effect of GB sliding and Coble creep on the anomalous dependence of the activation volume on temperature observed in nanocrystalline Ni. It is demonstrated that although an account for GB sliding and Coble creep leads to the appearance of cusps in the temperature dependence of the activation volume, these mechanisms alone cannot be responsible for the observed anomalous dependence of the activation volume on temperature.

2015 ◽  
Vol 102 ◽  
pp. 99-102 ◽  
Author(s):  
D.V. Gunderov ◽  
G. Maksutova ◽  
A. Churakova ◽  
A. Lukyanov ◽  
A. Kreitcberg ◽  
...  

2006 ◽  
Vol 503-504 ◽  
pp. 31-36 ◽  
Author(s):  
Johannes Mueller ◽  
Karsten Durst ◽  
Dorothea Amberger ◽  
Matthias Göken

The mechanical properties of ultrafine-grained metals processed by equal channel angular pressing is investigated by nanoindentations in comparison with measurements on nanocrystalline nickel with a grain size between 20 and 400 nm produced by pulsed electrodeposition. Besides hardness and Young’s modulus measurements, the nanoindentation method allows also controlled experiments on the strain rate sensitivity, which are discussed in detail in this paper. Nanoindentation measurements can be performed at indentation strain rates between 10-3 s-1 and 0.1 s-1. Nanocrystalline and ultrafine-grained fcc metals as Al and Ni show a significant strain rate sensitivity at room temperature in comparison with conventional grain sized materials. In ultrafine-grained bcc Fe the strain rate sensitivity does not change significantly after severe plastic deformation. Inelastic effects are found during repeated unloading-loading experiments in nanoindentations.


2010 ◽  
Vol 667-669 ◽  
pp. 707-712 ◽  
Author(s):  
Xiao Yan Liu ◽  
Xi Cheng Zhao ◽  
Xi Rong Yang

Ultrafine-grained (UFG) commercially pure (CP) Ti with a grain size of about 200 nm was produced by ECAP up to 8 passes using route BC at room temperature. For ECAP processing a proper die set was designed and constructed with an internal channel angle Φ of 120° and an outer arc of curvature Ψ of 20°. Strain rate sensitivity of UFG CP-Ti and CG CP-Ti were investigated by compression tests in the temperature range of 298~673K and strain rate range of 10-4~100s-1 using Gleeble simulator machine. Evolution of the microstructure during compression testing was observed using optical microscopy (OM) and transmission electron microscopy (TEM). Strain rate sensitivity value m of the UFG CP-Ti has been measured and is found to increase with increasing temperature and decreasing strain rate, and is enhanced compared to that of CG CP-Ti. Result of the deformation activation energy determination of UFG CP-Ti indicates that the deformation mechanism in UFG CP-Ti is correlated to the grain boundaries.


2013 ◽  
Vol 228 ◽  
pp. S254-S256 ◽  
Author(s):  
F. Wang ◽  
B. Li ◽  
T.T. Gao ◽  
P. Huang ◽  
K.W. Xu ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document