scholarly journals Generate Various Parameters Of Trv Envelope Synthetic Test Circuit

2021 ◽  
Vol 12 (2) ◽  
pp. 1348-1356
Author(s):  
Jagadeesh Peddapudi, Et. al.
Keyword(s):  
High Voltage ◽  
Short Circuit ◽  
Circuit Breaker ◽  
Circuit Breakers ◽  
Force System ◽  
Transient Recovery Voltage ◽  
Test Circuit ◽  
Synthetic Test ◽  
Recovery Voltage ◽  
The Impact

The most basic transient a circuit breaker needs to suffer during its activity is the transient recovery voltage (TRV), started by the electric force system as a characteristic response on flow interference. To test high voltage CBs, direct testing utilizing the force system or short out alternators are not practical. The testing of high voltage Circuit Breakers (CBs) of bigger limit requires huge limit of testing station. An equal infusion of short out current and transient voltage to medium and high voltage circuit breaker (CB) by a synthetic model is examined. Transient recovery voltage is made by a capacitor bank and is applied to CB. An optical set off spark gap has been utilized to interrupt short circuit and to introduce of transient recovery voltage that is applied across the contacts of circuit breaker. Transient recovery voltage examination can never be done totally, as the advancement of circuit breaker development and organization configuration goes on. The most widely recognized way to deal with TRV examination is concerning the supposed planned TRV, in which a suspicion of dismissing association between circuit breaker itself and the innate system recovery voltage is being made. Notwithstanding, it actually is by all accounts qualified to examine what circuit breaker means for transient recovery voltage. An ideal grouping to open/close of reinforcement test article and helper circuit breakers inside suitable chance to infuse of recovery voltage. The impact of reactance of inductive flaw current limiter just as distance to blame in short line issue condition on pace of ascent of recovery voltage. A 4-boundaries TRV synthetic test circuit dependent on equal current infusion technique is planned and mimicked for testing 145kV rating circuit-breakers according to new TRV prerequisites given in IEC 62271-100.

scholarly journals Comparison of the Interrupting Capability of Gas Circuit Breaker According to SF6, g3, and CO2/O2 Mixture

Energies ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 6388
Author(s):  
Woo-Young Lee ◽  
Jang-Un Jun ◽  
Ho-Seok Oh ◽  
Jun-Kyu Park ◽  
Yeon-Ho Oh ◽  
...  
Keyword(s):  
Circuit Breaker ◽  
Filling Pressure ◽  
The Other ◽  
Zero Crossing ◽  
Arc Voltage ◽  
Transient Recovery Voltage ◽  
Test Circuit ◽  
Arc Current ◽  
Recovery Voltage ◽  
Current Zero

In the study, an interrupting performance test on the 145 kV gas circuit breaker is performed according to three different gases: SF6, g3 (5% NovecTM4710 with 95% CO2), and CO2(70%)/O2(30%) gases. Thanks to research advancements, it is confirmed that CO2 and g3 (5% NovecTM 4710) gases, respectively, have 40% and 75% dielectric strength, compared to that of SF6 gas. The filling pressure and transient recovery voltage criteria of each gas were determined differently in order to compare the maximum interrupting performance of each gas. The pressure of SF6 gas was determined to be 5.5 bar, which is typically used in circuit breakers. The pressure of the other two gases was determined to be 8.0 bar (the maximum available pressure of the test circuit breaker) to find the maximum interrupting performance. Moreover, the rate-of-rise of transient recovery voltage of SF6 was determined as 10 kV/μs, which is the value at the state of maximum interrupting performance of the test circuit breaker with SF6. On the other hand, the rate-of-rise of transient recovery voltages of g3 (5% NovecTM4710 with 95% CO2) and CO2(70%)/O2(30%) gases were, respectively, determined as 4∼5 kV/μs to find the interruption available point. The characteristics of arc conductance, arc current, and arc voltage near the current zero, and post-arc current are analyzed to compare the interrupting performance, according to different arc-quenching gases. The arc current is measured using a current transformer (Rogowski coil), and a signal processing method of the arc current and arc voltage is introduced to increase the reliability of the interrupting performance results. As a result of the test, it is confirmed that the critical arc conductance for all test conditions converged within a certain range and the value is around 0.7 mS. In addition, the critical current slope just before the current zero-crossing during the interrupting process is shown to be 1.8 A/μs between interruption success and failure. Consequently, it is verified that the CO2(70%)/O2(30%) mixture and g3 (5% NovecTM4710 with 95% CO2) have a similar arc extinguishing performance and SF6 has a relatively higher extinguishing performance than that of CO2(70%)/O2(30%) mixture and g3 (5% NovecTM4710 with 95% CO2) under the aforementioned filling pressure and TRV conditions.

Electrical Stress Analysis of Switching Transients in 115 kV High Voltage Substation

2015 ◽  
Vol 781 ◽  
pp. 333-336
Author(s):  
Ratana Kem ◽  
Warunee Srisongkram ◽  
Phanupong Fuangpian ◽  
Thanapong Suwanasri
Keyword(s):  
Stress Analysis ◽  
Capacitor Bank ◽  
Circuit Breaker ◽  
Inrush Current ◽  
Circuit Breakers ◽  
Power Circuit ◽  
Electrical Stress ◽  
Transient Recovery Voltage ◽  
Recovery Voltage

This paper presents electrical stress analysis from capacitor bank switching in a 115 kV substation. The actual data of all equipment in substation are used in the simulated circuit by using ATP/EMTP program. The cases study focused on the determination of proper value of series reactor, effect of circuit breaker pole discrepancy on inrush current, line model selection and load variation. Electrical stress from energizing inrush current as well as transient recovery voltage and rate of rise of recovery voltage imposed on power circuit breaker during capacitor bank has been analyzed. The obtained results are used as guidelines for analysis of the electric stresses on substation equipment while capacitor banks are energized. Moreover, those results can be used to select the proper rating of circuit breakers to withstand the electric stresses in the transmission network.

Sign in / Sign up

Export Citation Format

Share Document