scholarly journals Evaluation of Mandibular Tooth Supported Over-Denture with Two Different Denture Base Materials

2018 ◽  
Vol 5 (1) ◽  
pp. 421-428
Author(s):  
Reham Elshiekh ◽  
Yasmeen El-Mahdy ◽  
Dina Kholeif
Keyword(s):  
Denture Base ◽  
Mandibular Tooth ◽  
Base Materials

The need for radiopaque denture base materials: A review of the literature

1971 ◽  
Vol 5 (3) ◽  
pp. 245-252 ◽  
Author(s):  
H. H. Chandler ◽  
R. L. Bowen ◽  
G. C. Paffenbarger
Keyword(s):  
Review Of The Literature ◽  
Denture Base ◽  
Base Materials

Reinforcement of denture base materials with Nano sisal fibers powder

2021 ◽  
Author(s):  
Teba M. Hameed ◽  
Balqees M. Al –Dabbagh ◽  
Ragdaa K. Jasim
Keyword(s):  
Denture Base ◽  
Base Materials ◽  
Sisal Fibers

scholarly journals Enhancement of the Tensile and the Compression Properties for Heat- Cured Acrylic Resin Denture Base Materials

2018 ◽  
Vol 15 (4) ◽  
pp. 449-454
Author(s):  
Baghdad Science Journal
Keyword(s):  
Polymethyl Methacrylate ◽  
Compression Strength ◽  
Base Material ◽  
Acrylic Resin ◽  
Tensile Tests ◽  
Strength Test ◽  
Denture Base ◽  
Compression Properties ◽  
Base Materials ◽  
Styrene Butadiene

This work aims to investigate the tensile and compression strengths of heat- cured acrylic resin denture base material by adding styrene-butadiene (S- B) to polymethyl methacrylate (PMMA). The most well- known issue in prosthodontic practice is fracture of a denture base. All samples were a blend of (90%, 80%) PMMA and (10%, 20%) S- B powder melted in Oxolane (Tetra hydro furan). These samples were chopped down into specimens of dimensions 100x10x2.5mm to carry out the requirements of tensile tests. The compression strength test specimens were shaped into a cylinder with dimensions of 12.7mm in diameter and 20mm in length. The experimental results show a significant increase in both tensile and compression strengths when compared to control (standard) results for the preparation material.

scholarly journals Tensile and transverse strength of novel copolymers for denture base.

2019 ◽  
Vol S (1) ◽  
pp. 7-10
Author(s):  
Ahmed Asim Saeed Al-Ali ◽  
◽  
Ammar k. Al-Noori ◽  
Amer A. Taqa ◽  
◽  
...  
Keyword(s):  
Acrylic Resin ◽  
P Value ◽  
Transverse Strain ◽  
The Novel ◽  
Denture Base ◽  
Transverse Strength ◽  
Base Materials ◽  
Propenoic Acid ◽  
Significant Difference ◽  
Transverse Strains

Objectives: Compare tensile and transverse strength of new copolymers for denture base. Materials and methods: The specimens were prepared from heat cured acrylic resin with three types of additives: Acryester B, Ethoxycarbonylethylene, and Propenoic acid at a percentage of 5% and 10%. The tensile and transverse strains were tested, recorded and compared. Results: The analysis of variance display statistically significant difference. The p-value was 0.001 for each of tensile and transverse strain tests. Conclusions: The tensile strength of the novel copolymers increased. The transverse strength of some of the novel copolymers increased.

Sign in / Sign up

Export Citation Format

Share Document