scholarly journals Three-Dimensional Characterization of Slipping-Off Fracture Surface in a 1 mass%N Bearing Austenitic Stainless Steel

2009 ◽  
Vol 73 (4) ◽  
pp. 283-289 ◽  
Author(s):  
M. Ojima ◽  
Y. Adachi ◽  
Y. Tomota ◽  
K. Ikeda ◽  
Y. Katada
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Fracture Surface ◽  
Three Dimensional

Two- and three-dimensional microstructural characterization of a super-austenitic stainless steel

2006 ◽  
Vol 418 (1-2) ◽  
pp. 11-18 ◽  
Author(s):  
A.C. Lewis ◽  
J.F. Bingert ◽  
D.J. Rowenhorst ◽  
A. Gupta ◽  
A.B. Geltmacher ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Three Dimensional ◽  
Microstructural Characterization ◽  
Super Austenitic Stainless Steel

Characterization of Hot-Steam Oxidation Tested Chromosiliconized Heat-Resistant Austenitic Stainless Steel

2012 ◽  
Vol 53 (6) ◽  
pp. 1090-1093 ◽  
Author(s):  
Yasuhiro Hoshiyama ◽  
Xiaoying Li ◽  
Hanshan Dong ◽  
Akio Nishimoto
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Steam Oxidation ◽  
Heat Resistant

Characterization of Thermal Oxides on Austenitic Stainless Steel

2008 ◽  
Vol 50 (6) ◽  
pp. 312-317
Author(s):  
Vesna Alar ◽  
Željko Alar ◽  
Vera Rede
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel

Characterization of thick and soft DLC coatings deposited on plasma nitrided austenitic stainless steel

2015 ◽  
Vol 59 ◽  
pp. 73-79 ◽  
Author(s):  
Eugenia L. Dalibón ◽  
Daniel Heim ◽  
Christian Forsich ◽  
Andreas Rosenkranz ◽  
M. Agustina Guitar ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Dlc Coatings

Characterization of microstructure and texture across dissimilar super duplex/austenitic stainless steel weldment joint by super duplex filler metal

2015 ◽  
Vol 106 ◽  
pp. 27-35 ◽  
Author(s):  
Abbas Eghlimi ◽  
Morteza Shamanian ◽  
Masoomeh Eskandarian ◽  
Azam Zabolian ◽  
Jerzy A. Szpunar
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Filler Metal ◽  
Steel Weldment ◽  
Stainless Steel Weldment

Magnetic Characterization of SUS316L Deformed by High Pressure Torsion

2011 ◽  
Vol 239-242 ◽  
pp. 1300-1303
Author(s):  
Hong Cai Wang ◽  
Minoru Umemoto ◽  
Innocent Shuro ◽  
Yoshikazu Todaka ◽  
Ho Hung Kuo
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Stainless Steel ◽  
Phase Transformation ◽  
Austenitic Stainless Steel ◽  
Volume Fraction ◽  
High Pressure Torsion ◽  
Austenitic Matrix ◽  
Magnetic Characterization

SUS316L austenitic stainless steel was subjected to severe plastic deformation (SPD) by the method of high pressure torsion (HPT). From a fully austenitic matrix (γ), HPT resulted in phase transformation from g®a¢. The largest volume fraction of 70% a¢ was obtained at 0.2 revolutions per minute (rpm) while was limited to 3% at 5rpm. Pre-straining of g by HPT at 5rpm decreases the volume fraction of a¢ obtained by HPT at 0.2rpm. By HPT at 5rpm, a¢®g reverse transformation was observed for a¢ produced by HPT at 0.2rpm.

Nanoindentation characterization of nano-twinned grains in an austenitic stainless steel

2016 ◽  
Vol 112 ◽  
pp. 19-22 ◽  
Author(s):  
F.K. Yan ◽  
B.B. Zhang ◽  
H.T. Wang ◽  
N.R. Tao ◽  
K. Lu
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel

In-situ EBSD study of the degradation behavior in a type 316 Austenitic Stainless Steel during plastic deformation

2021 ◽  
pp. 030932472098493
Author(s):  
Xiao Wang ◽  
Yuetao Zhang ◽  
Huaying Li ◽  
Ming-yu Huang
Keyword(s):  
Plastic Deformation ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Tensile Deformation ◽  
Target Surface ◽  
Local Orientation ◽  
Deformation Degree ◽  
Band Contrast

Type 316 steels have been heavily utilized as the structural material in many construction equipment and infrastructures. This paper reports the characterization of degradation in 316 austenitic stainless steel during the plastic deformation. The in-situ EBSD results revealed that, with the increase of plastic strain, the band contrast (BC) value progressively decreased in both grain and grain boundaries, and the target surface becomes uneven after the plastic tensile, which indicates that the increase of surface roughness. Meanwhile, the KAM and ρGND values are low in the origin specimen but increased significantly after the in-situ tensile. The results indicated that the KAM and ρGND are closely related to the deformation degree of the materials, which can be used as the indicator for assessing the degradation of 316 steel. Besides, the re-orientation of grain occurred after the tensile deformation, which can be recognized from the lattice orientation and local orientation maps.

Sign in / Sign up

Export Citation Format

Share Document