Comparison of Analytical Model for Contact Mechanics Parameters with Numerical Analysis and Experimental Results

2019 ◽  
Vol 48 (3) ◽  
pp. 168-187
Author(s):  
Sunish Vadakkeveetil ◽  
Arash Nouri ◽  
Saied Taheri
Keyword(s):  
Finite Element ◽  
Numerical Analysis ◽  
Finite Element Model ◽  
Penetration Depth ◽  
Contact Mechanics ◽  
Analytical Model ◽  
Element Model ◽  
Experimental Results ◽  
Nano Indentation ◽  
Interfacial Separation

ABSTRACT Being able to estimate tire/rubber friction is very important to tire engineers, materials developers, and pavement engineers. This is because of the need for estimating forces generated at the contact, optimizing tire and vehicle performance, and estimating tire wear. Efficient models for contact area and interfacial separation are key for accurate prediction of friction coefficient. Based on the contact mechanics and surface roughness, various models were developed that can predict real area of contact and penetration depth/interfacial separation. In the present work, we intend to compare the analytical contact mechanics models using experimental results and numerical analysis. Nano-indentation experiments are performed on the rubber compound to obtain penetration depth data. A finite element model of a rubber block in contact with a rough surface was developed and validated using the nano-indentation experimental data. Results for different operating conditions obtained from the developed finite element model are compared with analytical model results, and further model improvements are discussed.

Modelling of 4H-SiC VJFETs with Self-Aligned Contacts

2016 ◽  
Vol 858 ◽  
pp. 913-916 ◽  
Author(s):  
Konstantinos Zekentes ◽  
Konstantin Vassilevski ◽  
Antonis Stavrinidis ◽  
George Konstantinidis ◽  
Maria Kayambaki ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Analytical Model ◽  
Element Model ◽  
Experimental Results ◽  
Compact Model ◽  
Channel Lengths ◽  
The Finite Element Model

Purely vertical 4H-SiC JFETs have been modeled by using three different approaches: the analytical model, the finite element model and the compact model. The results of the modeling have been compared with experimental results on a series of fabricated self-aligned devices with two different channel lengths (0.3 and 1.1μm) and various channel widths (1.5, 2, 2.5, 3, 4 and 5 μm). For all the considered models I-V and C-V characteristics could be satisfactorily simulated.

Validation of a finite element model of the human elbow for determining cartilage contact mechanics

2013 ◽  
Vol 46 (10) ◽  
pp. 1767-1771 ◽  
Author(s):  
Ryan T. Willing ◽  
Emily A. Lalone ◽  
Hannah Shannon ◽  
James A. Johnson ◽  
Graham J.W. King
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Contact Mechanics ◽  
Element Model

scholarly journals Co-Simulation of an Inverter Fed Permanent Magnet Synchronous Machine

2014 ◽  
Vol 6 (1) ◽  
pp. 19-25
Author(s):  
Gergely Máté Kiss ◽  
István Vajda
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Analytical Model ◽  
Element Model ◽  
Electrical Machine ◽  
Permanent Magnet Synchronous Machine ◽  
Variable Speed ◽  
Analytical Variable ◽  
Drive Model ◽  
The Finite Element Model

Abstract Co-simulation is a method which makes it possible to study the electric machine and its drive at once, as one system. By taking into account the actual inverter voltage waveforms in a finite element model instead of using only the fundamental, we are able to study the electrical machine's behavior in more realistic scenario. The recent increase in the use of variable speed drives justifies the research on such simulation techniques. In this paper we present the co-simulation of an inverter fed permanent magnet synchronous machine. The modelling method employs an analytical variable speed drive model and a finite element electrical machine model. By linking the analytical variable speed drive model together with a finite element model the complex simulation model enables the investigation of the electrical machine during actual operation. The methods are coupled via the results. This means that output of the finite element model serves as an input to the analytical model, and the output of the analytical model provides the input of the finite element model for a different simulation, thus enabling the finite element simulation of an inverter fed machine. The resulting speed and torque characteristics from the analytical model and the finite element model show a good agreement. The experiences with the co-simulation technique encourage further research and effort to improve the method.

The Flattening Behaviour of Angle Section Beams Subjected to Pure Bending

2014 ◽  
Vol 501-504 ◽  
pp. 2479-2483
Author(s):  
Wei Bin Yuan ◽  
Chang Yi Chen
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Analytical Solutions ◽  
Element Model ◽  
Nonlinear Finite Element ◽  
Experimental Results ◽  
Energy Methods ◽  
Pure Bending ◽  
Angle Section ◽  
Nonlinear Finite Element Model

The flattening behaviour of angle section beams subjected to pure bending is studied in this paper. Analytical solutions for static instabilities of angle section beams subjected to pure bending about its weak axis are derived using energy methods. Nonlinear finite element model using the code ANSYS is developed to simulate nonlinear snap-through instability of angle section beams under pure bending. The optimization assumption about flattening shape of the leg is proposed, through comparison of between the present solutions, experimental results, and the finite element results.

Sign in / Sign up

Export Citation Format

Share Document