scholarly journals Structure and Properties of Slags Used in the Continuous Casting of Steel: Part 1 Conventional Mould Powders

2016 ◽  
Vol 56 (1) ◽  
pp. 1-13 ◽  
Author(s):  
Kenneth C. Mills
Keyword(s):  
Continuous Casting ◽  
Steel Part ◽  
Continuous Casting Of Steel ◽  
Structure And Properties

A mold simulator for the continuous casting of steel: Part I. The development of a simulator

2005 ◽  
Vol 36 (3) ◽  
pp. 355-371 ◽  
Author(s):  
A. Badri ◽  
T. T. Natarajan ◽  
C. C. Snyder ◽  
K. D. Powers ◽  
F. J. Mannion ◽  
...  
Keyword(s):  
Continuous Casting ◽  
Steel Part ◽  
Continuous Casting Of Steel

scholarly journals On the formation of fold-type oscillation marks in the continuous casting of steel

2017 ◽  
Vol 4 (6) ◽  
pp. 170062 ◽  
Author(s):  
M. Vynnycky ◽  
S. Saleem ◽  
K. M. Devine ◽  
B. J. Florio ◽  
S. L. Mitchell ◽  
...  
Keyword(s):  
Continuous Casting ◽  
Asymptotic Methods ◽  
Continuous Casting Of Steel ◽  
Oscillation Mark ◽  
Governing Equations ◽  
Fold Type ◽  
Parameters Analysis ◽  
Oscillation Marks ◽  
Recent Experimental Work ◽  
Type Oscillation

Asymptotic methods are employed to revisit an earlier model for oscillation-mark formation in the continuous casting of steel. A systematic non-dimensionalization of the governing equations, which was not carried out previously, leads to a model with 12 dimensionless parameters. Analysis is provided in the same parameter regime as for the earlier model, and surprisingly simple analytical solutions are found for the oscillation-mark profiles; these are found to agree reasonably well with the numerical solution in the earlier model and very well with fold-type oscillation marks that have been obtained in more recent experimental work. The benefits of this approach, when compared with time-consuming numerical simulations, are discussed in the context of auxiliary models for macrosegregation and thermomechanical stresses and strains.

Influence of the configuration of the submerged entry nozzle inner channel and electromagnetic effect within its length on the qualitative distribution of metal flows during continuous casting of steel

2021 ◽  
pp. 17-22
Author(s):  
A. Yu. Tretyak ◽  
◽  
Qiang Wang ◽  
Chun-Lei Wu ◽  
E. I. Shifrin ◽  
...  
Keyword(s):  
Quality Control ◽  
Continuous Casting ◽  
Submerged Entry Nozzle ◽  
Electromagnetic Stirring ◽  
Continuous Casting Of Steel ◽  
Electromagnetic Effect ◽  
Inner Surface ◽  
Continuously Cast ◽  
Inner Channel ◽  
Research Show

Today, the most promising and effective method of quality control of the continuously cast billets is electromagnetic stirring of the melt. In this case, an important component is the effect of the stirring on the jet in the nozzle. Moreover, as research has shown, this method is highly dependent on the configuration of the inner channel of the nozzle. Research have shown that positive or negative taper of the inner surface of the nozzle allows to obtain different results after applying EMS. Taper control completely changes the pattern of the melt flow and its deceleration in the mold, especially when it is casting of large billets. The results of the research show that minor changes in the taper of the nozzle significantly increase the effect of EMS implementation, which is observed already at 0.27 % of positive the taper and increases to 0.54%.

Sign in / Sign up

Export Citation Format

Share Document