MULTIPHASE FLOW SIMULATION OF CUTTINGS TRANSPORT ON HORIZONTAL WELLS - THE INFLUENCE RATE OF PENETRATION ON THE CLEANING PROCESS PERFORMANCE

Author(s):  
Joao Henrique Sartori ◽  
Renato Siqueira ◽  
Ayrton Cavallini Zotelle ◽  
Michel de Oliveira dos Santos
2021 ◽  
Vol 104 (1) ◽  
pp. 003685042110080
Author(s):  
Zheqin Yu ◽  
Jianping Tan ◽  
Shuai Wang

Shear stress is often present in the blood flow within blood-contacting devices, which is the leading cause of hemolysis. However, the simulation method for blood flow with shear stress is still not perfect, especially the multiphase flow model and experimental verification. In this regard, this study proposes an enhanced discrete phase model for multiphase flow simulation of blood flow with shear stress. This simulation is based on the discrete phase model (DPM). According to the multiphase flow characteristics of blood, a virtual mass force model and a pressure gradient influence model are added to the calculation of cell particle motion. In the experimental verification, nozzle models were designed to simulate the flow with shear stress, varying the degree of shear stress through different nozzle sizes. The microscopic flow was measured by the Particle Image Velocimetry (PIV) experimental method. The comparison of the turbulence models and the verification of the simulation accuracy were carried out based on the experimental results. The result demonstrates that the simulation effect of the SST k- ω model is better than other standard turbulence models. Accuracy analysis proves that the simulation results are accurate and can capture the movement of cell-level particles in the flow with shear stress. The results of the research are conducive to obtaining accurate and comprehensive analysis results in the equipment development phase.


Author(s):  
Wei Li ◽  
Daoming Liu ◽  
Mathieu Desbrun ◽  
Jin Huang ◽  
Xiaopei Liu

Heat Transfer ◽  
2020 ◽  
Vol 49 (5) ◽  
pp. 2849-2867
Author(s):  
Deepak Meerakaviyad ◽  
Tony Keville ◽  
Atma Prakash ◽  
Abdullah Sajid ◽  
Faik Hamad

Author(s):  
Evren M. Ozbayoglu ◽  
Flavio Rodrigues ◽  
Reza Ettehadi ◽  
Roland May ◽  
Dennis Clapper

Abstract As explorations advance and drilling techniques become more innovative, complex and challenging trajectories arise. In consequence, cuttings transport has continued to be a subject of interest because, if the drilled cuttings cannot be removed from the wellbore, drilling cannot proceed for long. Therefore, efficient cleaning of highly inclined and horizontal wellbores is still among the most important problems to solve, because these types of wells require specialized fluid formulations and/or specific hole cleaning techniques. There are numerous studies and methods that focus in cuttings transportation in highly inclined and horizontal wells. One of them is the use of viscosity and density sweeps. Sweep pills have been used in the drilling industry as a tool to improve hole cleaning. This report presents the analysis of the performance of different sweeps pills working independently and in tandem in polymeric, oil and synthetic based systems and the comparison between them. The main objective of this project is to provide experimental evidence on which types of fluids perform better under certain conditions by studying the effect of viscosity and density in the bed erosion process in highly inclined and horizontal wells. In order to achieve that, several fluid formulations were tested at different inclination angles (90, 75, 60 degrees) in the Small Indoor Flow Loop property of The University of Tulsa’s Drilling Research Projects. The results of the tests are presented in terms of volume of drilled cuttings removed from the test section and measured differential pressures. All the tests were conducted under atmospheric pressure and ambient temperature. Moreover, a 2-Layer model is used for estimating the erosion performance of sweeps for design purposes, and the model estimations are compared with experimental results. From the experiments, it was identified that polymeric, oil and synthetic based muds with similar density and rheological properties eroded and transported the drilled cuttings similarly under similar test conditions. Furthermore, pumping the sweep pills in tandem demonstrated higher cuttings transport efficiency when compared with the sweep pills applied independently.


Sign in / Sign up

Export Citation Format

Share Document