scholarly journals Clinical Use of a Computer Assisted Reverse Total Shoulder Arthroplasty System: an Analysis of 1702 Cases

10.29007/hcd6 ◽  
2019 ◽  
Author(s):  
Alexander Greene ◽  
Sandrine Polakovic ◽  
Christopher Roche ◽  
Yifei Dai
Keyword(s):  
Shoulder Arthroplasty ◽  
Preoperative Planning ◽  
Total Shoulder Arthroplasty ◽  
Computer Assisted Surgery ◽  
Reverse Total Shoulder Arthroplasty ◽  
Computer Assisted ◽  
Glenoid Component ◽  
Implant Placement ◽  
Implant Selection ◽  
Reverse Total Shoulder

Placement of the glenoid component in reverse total shoulder arthroplasty (rTSA) is of paramount importance and can affect a patient’s range of motion postoperatively. Preoperative planning and computer assisted surgery (CAS) can improve upon glenoid placement, but such systems for rTSA have experienced limited commercial success. Postoperative surgical reports from the first 1702 clinical cases of a commercially available CAS rTSA system were collected and analyzed for implant selection, implant placement, and incision start to incision close operative time, and compared to similar date cohorts for non-navigated cases. Navigated rTSA cases had a significantly longer incision time than non-navigated cases. Augmented glenoid components were used in a much higher percentage of navigated cases than non-navigated cases, suggesting that augmented glenoid components provide utility for correcting pathologic glenoid wear. The average resultant version and inclination of the implanted component increased with the size of augment used, suggesting there may not be a clear consensus on optimal version or inclination. Long term clinical follow up will need to be collected to determine if preoperative planning combined with more precise and accurate glenoid component positioning leads to improved clinical outcomes and implant longevity.

scholarly journals Clinical Use of a Computer Assisted Anatomic Total Shoulder Arthroplasty System: An Analysis of 574 Cases

10.29007/kld9 ◽  
2019 ◽  
Author(s):  
Alexander Greene ◽  
Sandrine Polakovic ◽  
Christopher Roche ◽  
Yifei Dai
Keyword(s):  
Clinical Outcomes ◽  
Shoulder Arthroplasty ◽  
Preoperative Planning ◽  
Total Shoulder Arthroplasty ◽  
Computer Assisted Surgery ◽  
Computer Assisted ◽  
Glenoid Component ◽  
Implant Placement ◽  
Implant Selection

Accurate reproduction of glenohumeral anatomy during anatomic total shoulder arthroplasty (aTSA) has been shown to correlate with positive clinical outcomes. Preoperative planning and computer assisted surgery (CAS) can improve upon glenoid placement, but such systems for aTSA have experienced limited commercial success. Postoperative surgical reports from the first 574 clinical cases of a commercially available CAS aTSA system were collected and analyzed for implant selection, implant placement, and incision start to incision close operative time, and compared to similar date cohorts for non-navigated cases. Navigated aTSA cases had a significantly longer incision time than non-navigated cases. Augmented glenoid components were used in a much higher percentage of navigated cases than non-navigated cases, suggesting that augmented glenoid components provide utility for correcting pathologic glenoid wear. The average resultant version of the implanted component increased with the size of augment used, suggesting there may not be a clear consensus on optimal retroversion. term clinical follow up will need to be collected to determine if preoperative planning combined with more precise and accurate glenoid component positioning leads to improved clinical outcomes and implant longevity.

Comparison of Methods to Predict Scapular Notching From Radiographs After Reverse Total Shoulder Arthroplasty

2012 ◽  
Author(s):  
Heath B. Henninger ◽  
Michael D. Harris ◽  
Kristen R. Petersen ◽  
Robert T. Burks ◽  
Robert Z. Tashjian
Keyword(s):  
Bone Loss ◽  
Shoulder Arthroplasty ◽  
Total Shoulder Arthroplasty ◽  
A Priori ◽  
Stress Shielding ◽  
Reverse Total Shoulder Arthroplasty ◽  
Scapular Notching ◽  
Implant Placement ◽  
And Function ◽  
Reverse Total Shoulder

Scapular notching is a complication of reverse total shoulder arthroplasty (rTSA) that results in bone loss on the lateral border of the scapula. Notching has been reported in up to 86% of patients at 5 year follow-up [1], and is graded 1–4 as a function of progressive bone loss [2]. Notching may arise from impingement, erosion, periprosthetic osteolysis, stress shielding or a combination of these [1]. Glenosphere position can mitigate notching by limiting hardware impingement [3–5], but may increase the forces required to abduct the arm [6]. Clinicians might optimize patient range of motion and function via implant placement if susceptibility to notching was known a-priori.

Preoperative three-dimensional computer planning for reverse total shoulder arthroplasty and bone grafting for severe glenoid deformity

2020 ◽  
pp. 175857322090890
Author(s):  
Robert Z Tashjian ◽  
Lindsay Beck ◽  
Irene Stertz ◽  
Peter N Chalmers
Keyword(s):  
Shoulder Arthroplasty ◽  
Bone Grafting ◽  
Total Shoulder Arthroplasty ◽  
Three Dimensional ◽  
Reverse Total Shoulder Arthroplasty ◽  
Patient Specific ◽  
Computer Assisted ◽  
Patient Specific Instrumentation ◽  
Reverse Total Shoulder ◽  
Glenoid Erosion

Background Computer assisted planning without patient specific instrumentation may be utilized to guide reverse total shoulder arthroplasty baseplate placement. The purpose of this study was to determine the difference between planned and achieved inclination and retroversion correction with three-dimensional preoperative computer assisted planning in reverse total shoulder arthroplasty without patient specific instrumentation with bone grafting for severe glenoid erosion. Methods Preoperative three-dimensional computer assisted planning without patient specific instrumentation was performed on 15 patients undergoing primary reverse total shoulder arthroplasty with glenoid bone grafting for severe glenoid erosion. On preoperative and immediate postoperative computed tomography slices, two-dimensional retroversion and inclination were measured. Preoperative three-dimensional baseline retroversion and inclination and planned postoperative three-dimensional retroversion and inclination were measured. Planned and achieved version and inclination changes were compared. Results The planned and achieved retroversion corrections were 18° and 12°, respectively (p < 0.001). The planned and achieved inclination corrections were 11° and 11°, respectively (p = 0.803). Conclusions Three-dimensional computer assisted planning without patient specific instrumentation in the setting of reverse total shoulder arthroplasty with severe glenoid erosion requiring bone grafting can accurately guide baseplate placement. All cases in which failure to correct retroversion or inclination within 10° of planning occurred in patients with severe erosion (B3 or E3 glenoids), therefore patient specific guides may be warranted in these cases to improve accuracy of implantation. Level of evidence Level IV, retrospective case series.

Sign in / Sign up

Export Citation Format

Share Document