scholarly journals Acoustical characterization of austenitic stainless steel welds for experimental and modeling NDT

2005 ◽  
Vol 17 (1/2) ◽  
pp. 76-81 ◽  
Author(s):  
Marie-Aude PLOIX ◽  
Rachid EL GUERJOUMA ◽  
Joseph MOYSAN ◽  
Gilles CORNELOUP ◽  
Bertrand CHASSIGNOLE
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Steel Welds

Characterization of Solidification Cracking in 304HCu Austenitic Stainless Steel Welds

2020 ◽  
Vol 73 (9) ◽  
pp. 2345-2353
Author(s):  
R. Ravibharath ◽  
V. Muthupandi ◽  
P. Bala Srinivasan ◽  
K. Devakumaran
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Solidification Cracking ◽  
Steel Welds

Characterization of Hot-Steam Oxidation Tested Chromosiliconized Heat-Resistant Austenitic Stainless Steel

2012 ◽  
Vol 53 (6) ◽  
pp. 1090-1093 ◽  
Author(s):  
Yasuhiro Hoshiyama ◽  
Xiaoying Li ◽  
Hanshan Dong ◽  
Akio Nishimoto
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Steam Oxidation ◽  
Heat Resistant

Characterization of Thermal Oxides on Austenitic Stainless Steel

2008 ◽  
Vol 50 (6) ◽  
pp. 312-317
Author(s):  
Vesna Alar ◽  
Željko Alar ◽  
Vera Rede
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel

Characterization of thick and soft DLC coatings deposited on plasma nitrided austenitic stainless steel

2015 ◽  
Vol 59 ◽  
pp. 73-79 ◽  
Author(s):  
Eugenia L. Dalibón ◽  
Daniel Heim ◽  
Christian Forsich ◽  
Andreas Rosenkranz ◽  
M. Agustina Guitar ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Dlc Coatings

Characterization of microstructure and texture across dissimilar super duplex/austenitic stainless steel weldment joint by super duplex filler metal

2015 ◽  
Vol 106 ◽  
pp. 27-35 ◽  
Author(s):  
Abbas Eghlimi ◽  
Morteza Shamanian ◽  
Masoomeh Eskandarian ◽  
Azam Zabolian ◽  
Jerzy A. Szpunar
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Filler Metal ◽  
Steel Weldment ◽  
Stainless Steel Weldment

Magnetic Characterization of SUS316L Deformed by High Pressure Torsion

2011 ◽  
Vol 239-242 ◽  
pp. 1300-1303
Author(s):  
Hong Cai Wang ◽  
Minoru Umemoto ◽  
Innocent Shuro ◽  
Yoshikazu Todaka ◽  
Ho Hung Kuo
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Stainless Steel ◽  
Phase Transformation ◽  
Austenitic Stainless Steel ◽  
Volume Fraction ◽  
High Pressure Torsion ◽  
Austenitic Matrix ◽  
Magnetic Characterization

SUS316L austenitic stainless steel was subjected to severe plastic deformation (SPD) by the method of high pressure torsion (HPT). From a fully austenitic matrix (γ), HPT resulted in phase transformation from g®a¢. The largest volume fraction of 70% a¢ was obtained at 0.2 revolutions per minute (rpm) while was limited to 3% at 5rpm. Pre-straining of g by HPT at 5rpm decreases the volume fraction of a¢ obtained by HPT at 0.2rpm. By HPT at 5rpm, a¢®g reverse transformation was observed for a¢ produced by HPT at 0.2rpm.

Nanoindentation characterization of nano-twinned grains in an austenitic stainless steel

2016 ◽  
Vol 112 ◽  
pp. 19-22 ◽  
Author(s):  
F.K. Yan ◽  
B.B. Zhang ◽  
H.T. Wang ◽  
N.R. Tao ◽  
K. Lu
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel
Sign in / Sign up

Export Citation Format

Share Document