scholarly journals EFFECT OF APPLICATION TOOLS AND VISCOSITY ON THICKNESS OF POLYURETHANE WATERPROOFING MEMBRANE IN VERTICAL PART

2020 ◽  
Vol 85 (775) ◽  
pp. 1123-1131
Author(s):  
Yuji HOSSHIN ◽  
Saori ISHIHARA ◽  
Katsuhiko NAKANO ◽  
Kyoji TANAKA
Keyword(s):  
Vertical Part ◽  
Waterproofing Membrane

Baloon dacryoplasty or nasolacrimal duct intubation for stenosis of lacrimal pathways vertical part in children?

Reflection ◽  
2018 ◽  
Vol 6 (1) ◽  
pp. 205-208
Author(s):  
M. I. Shlyakhtov ◽  
◽  
A. V. Krushinin ◽  
K. G. Naumov ◽  
◽  
...  
Keyword(s):  
Nasolacrimal Duct ◽  
Vertical Part

BEHAVIOR OF MECHANICALLY ANCHORED WATERPROOFING MEMBRANE EXPOSED IN HIGH WIND SPEED OF ACTUAL WIND

2006 ◽  
Vol 71 (610) ◽  
pp. 29-34 ◽  
Author(s):  
Hiroyuki MIYAUCHI ◽  
Nobuo KATO ◽  
Hirokazu ICHIKAWA ◽  
Takanori SASAKI ◽  
Kyoji TANAKA
Keyword(s):  
Wind Speed ◽  
High Wind ◽  
High Wind Speed ◽  
Waterproofing Membrane

scholarly journals Optimization and Practice of Energy-saving and Emission-reduction System for Production Process of Modified Asphalt Waterproofing Membrane

2017 ◽  
Vol 205 ◽  
pp. 930-936
Author(s):  
Bingwen Zhao ◽  
Lijuan Qi ◽  
Qiqi Zhao ◽  
Xiaoxiao Zhu
Keyword(s):  
Production Process ◽  
Energy Saving ◽  
Emission Reduction ◽  
Modified Asphalt ◽  
Reduction System ◽  
Waterproofing Membrane

The Oppel–Kundt Illusion and Its Relation to Horizontal-Vertical and Oblique Effects

Perception ◽  
2021 ◽  
pp. 030100662110065
Author(s):  
Klaus Landwehr
Keyword(s):  
Oblique Effect ◽  
The Other ◽  
Vertical Orientation ◽  
Horizontal Orientation ◽  
Full Circle ◽  
Original Stimulus ◽  
Vertical Part

The Oppel–Kundt illusion consists in the overestimation of the length of filled versus empty extents. Two experiments explored its relation to the horizontal-vertical illusion, which consists in the overestimation of the length of vertical versus horizontal extents, and to the oblique effect, which consists in poorer discriminative sensitivity for obliquely as opposed to horizontally or vertically oriented stimuli. For Experiment 1, Kundt’s (1863) original stimulus was rotated in steps of 45° full circle around 360°. For Experiment 2, one part of the stimulus remained at a horizontal or vertical orientation, whereas the other part was tilted 45° or 90°. The Oppel–Kundt illusion was at its maximum at a horizontal orientation of the stimulus. The illusion was strongly attenuated with L-type figures when the vertical part was empty, but not enhanced when this part was filled, suggesting that the horizontal-vertical illusion only acts on nontextured extents. There was no oblique effect.

Modern methods in treatment of lacrimal system vertical part obliteration

2021 ◽  
Vol 86 (4) ◽  
pp. 86
Author(s):  
M.M. Magomedov ◽  
E.L. Atkova ◽  
N.N. Krakhovetskiy ◽  
A.A. Maydanova ◽  
N.M. Magomedova
Keyword(s):  
Lacrimal System ◽  
Modern Methods ◽  
Vertical Part

Asphalt-Crumb Rubber Waterproofing Membrane

1978 ◽  
Vol 104 (1) ◽  
pp. 43-58
Author(s):  
Ronald K. Frobel ◽  
Gene R. Morris ◽  
C. Brent Cluff ◽  
Rudolph A. Jimenez
Keyword(s):  
Crumb Rubber ◽  
Waterproofing Membrane

Stress Analysis and Microstructure Evolution of Titanium Alloy Pipe during Flattening Processing

2019 ◽  
Vol 944 ◽  
pp. 1088-1093
Author(s):  
Jun Chen ◽  
She Wei Xin ◽  
Wei Zhou ◽  
Qian Li ◽  
Si Yuan Zhang ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Tensile Stress ◽  
Compressive Stress ◽  
Outer Layer ◽  
Contact Stage ◽  
Straight Wall ◽  
Vertical Part ◽  
Left And Right ◽  
Titanium Alloy Tube ◽  
Flattening Process

TA24 titanium alloy pipe with 638mm diameter and 19mm wall thickness is carried out continuous load flatten test, and the stress of internal and external pipe wall during flatten process is studied in this paper. The results show that the TA24 titanium alloy tube has good flattening performance, and the flattening process has experienced original stage, flattened oblate stage, flattened straight wall stage, flattened depressed stage, flattened concave contact stage. During the flattening process, the outer layer of the upper and lower wall of the tube is subjected to compressive stress, and the inner layer material is subjected to tensile stress. The tensile and compressive forces cause the vertical part of the upper and lower walls to be concave. The outer layer of the left and right circular arc parts is subjected to tensile stress and the inner layer is subjected to tensile stress. The compressive stress also causes the radius of the arc to decrease due to the combined force of the tensile and compressive forces, that is, the flattening occurs. With the decrease of and pressing distance under continuous loading condition, the metal on the left and right sides of the pipe gathers toward the middle depression, which aggravates the deformation of the upper and lower walls until the upper and lower walls contact, and the arc radius of the left and right walls decreases until the outer surface cracks. The pipe microstructure changes significantly into elongated deformation structure during the flattening process. The most severe part of the deformation is the left and right end arc of the pipe, followed by the upper and lower end depression.

Sign in / Sign up

Export Citation Format

Share Document