titanium alloy tube
Recently Published Documents


TOTAL DOCUMENTS

34
(FIVE YEARS 3)

H-INDEX

5
(FIVE YEARS 0)



2021 ◽  
Vol 1014 (1) ◽  
pp. 012023
Author(s):  
K G Martynov ◽  
D A Negodin ◽  
D N Klimenko ◽  
Yu A Gladkov ◽  
S V Zherebtsov


2021 ◽  
Vol 1016 ◽  
pp. 1181-1187
Author(s):  
Yun Lian Qi ◽  
Li Ying Zeng ◽  
Wei Liu ◽  
Hua Mei Sun ◽  
Yu Du ◽  
...  

Effects of extrusion temperature and heat treatment process on the microstructure and mechanical properties of Ti-1300 titanium alloy tube billets were studied by tensile testing and microstructure observation, and the relationship among the thermal processing technique and microscopic structure and mechanical properties of the billets were also investigated. The results showed that the transverse structure of Ti-1300 alloy after extrusion in the a+b two-phase region was uniform and fine. And the longitudinal structure could be seen that the extrusion processing streamline was broken uniformly. Ti-1300 alloy extruded at a+b two-phase has a good match of the strength and ductility, and the ductility of two-phase extrusion is obviously better than that of β single-phase extrusion, especially for the reduction of area.



Author(s):  
Zhongze Yang ◽  
Wenchen Xu ◽  
He Wu ◽  
Xingjie Wan ◽  
Yu Chen ◽  
...  


2020 ◽  
Vol 279 ◽  
pp. 116520 ◽  
Author(s):  
Heng Li ◽  
Dong Wei ◽  
Haiqin Zhang ◽  
Heng Yang ◽  
Haoran Liu ◽  
...  


Micromachines ◽  
2020 ◽  
Vol 11 (3) ◽  
pp. 314 ◽  
Author(s):  
Wanli Song ◽  
Zhen Peng ◽  
Peifan Li ◽  
Pei Shi ◽  
Seung-Bok Choi

In this study, a novel magnetorheological (MR) polishing device under a compound magnetic field is designed to achieve microlevel polishing of the titanium tubes. The polishing process is realized by combining the rotation motion of the tube and the reciprocating linear motion of the polishing head. Two types of excitation equipment for generating an appropriate compound magnetic field are outlined. A series of experiments are conducted to systematically investigate the effect of compound magnetic field strength, rotation speed, and type and concentration of abrasive particles on the polishing performance delivered by the designed device. The experiments were carried out through controlling variables. Before and after the experiment, the surface roughness in the polished area of the workpiece is measured, and the influence of the independent variable on the polishing effect is judged by a changing rule of surface roughness so as to obtain a better parameter about compound magnetic field strength, concentration of abrasive particles, etc. It is shown from experimental results that diamond abrasive particles are appropriate for fine finishing the internal surface of the titanium-alloy tube. It is also identified that the polishing performance is excellent at high magnetic field strength, fast rotation speed, and high abrasive-particle concentration.





2019 ◽  
Vol 375 ◽  
pp. 164-170 ◽  
Author(s):  
N.M. Santos ◽  
S.F.M. Mariano ◽  
M. Ueda


2019 ◽  
Vol 944 ◽  
pp. 1088-1093
Author(s):  
Jun Chen ◽  
She Wei Xin ◽  
Wei Zhou ◽  
Qian Li ◽  
Si Yuan Zhang ◽  
...  

TA24 titanium alloy pipe with 638mm diameter and 19mm wall thickness is carried out continuous load flatten test, and the stress of internal and external pipe wall during flatten process is studied in this paper. The results show that the TA24 titanium alloy tube has good flattening performance, and the flattening process has experienced original stage, flattened oblate stage, flattened straight wall stage, flattened depressed stage, flattened concave contact stage. During the flattening process, the outer layer of the upper and lower wall of the tube is subjected to compressive stress, and the inner layer material is subjected to tensile stress. The tensile and compressive forces cause the vertical part of the upper and lower walls to be concave. The outer layer of the left and right circular arc parts is subjected to tensile stress and the inner layer is subjected to tensile stress. The compressive stress also causes the radius of the arc to decrease due to the combined force of the tensile and compressive forces, that is, the flattening occurs. With the decrease of and pressing distance under continuous loading condition, the metal on the left and right sides of the pipe gathers toward the middle depression, which aggravates the deformation of the upper and lower walls until the upper and lower walls contact, and the arc radius of the left and right walls decreases until the outer surface cracks. The pipe microstructure changes significantly into elongated deformation structure during the flattening process. The most severe part of the deformation is the left and right end arc of the pipe, followed by the upper and lower end depression.



Sign in / Sign up

Export Citation Format

Share Document