Falling Weight Deflectometer Joint Load Tests Used for Direct Calculation of Pavement Joint Stiffness

2012 ◽  
Vol 2306 (1) ◽  
pp. 95-104 ◽  
Author(s):  
Christopher R. Byrum
2001 ◽  
Vol 38 (5) ◽  
pp. 924-935 ◽  
Author(s):  
J -M Konrad ◽  
D Lachance

This paper presents the results of an extensive field investigation of several instrumented road sections in the Province of Quebec, Canada. Falling-weight deflectometer tests, static load tests on embedded plates at different depths, large dynamic cone penetration (DCP) tests, and piezocone tests (CPTU) were performed to study the mechanical response of the pavement. A correlation between elastic deformation modulus inferred from the plate load tests and DCP penetration index was obtained for nine different sites. A correlation between the equivalent elastic modulus of uniform subgrade soils and piezocone tip resistance was also established using data from the falling-weight deflectometer. A procedure for calculating the deflection basin for any pavement system placed over a more complex subgrade stratigraphy was proposed using these correlations. The proposed procedure was validated on two sites and its performance was adequate, since the calculated deflection basins agreed well with the measured deflection basins.Key words: penetration test, piezocone, deflection, pavement, in situ.


1997 ◽  
Vol 1570 (1) ◽  
pp. 143-150 ◽  
Author(s):  
Lev Khazanovich ◽  
Jeffery Roesler

A neural-network-based backcalculation procedure is developed for multilayer composite pavement systems. The constructed layers are modeled as compressible elastic layers, whereas the subgrade is modeled as a Winkler foundation. The neural networks are trained to find moduli of elasticity of the constructed layers and a coefficient of subgrade reaction to accurately match a measured deflection profile. The method was verified by theoretically generated deflection profiles and falling weight deflectometer data measurements conducted at Edmonton Municipal Airport, Canada. For the theoretical deflection basins, the results of backcalculation were compared with actual elastic parameters, and excellent agreement was observed. The results of backcalculation using field test data were compared with the results obtained using WESDEF. Similar trends were observed for elastic parameters of all the pavement layers. The backcalculation procedure is implemented in a computer program called DIPLOBACK.


2019 ◽  
Vol 15 (1) ◽  
pp. 29-35
Author(s):  
Jozef Komačka ◽  
IIja Březina

Abstract The propagation of waves generated by load impulse of two FWD types was assessed using test outputs in the form of time history data. The calculated travel time of wave between the receiver in the centre of load and others receivers showed the contradiction with the theory as for the receivers up to 600 (900) mm from the centre of load. Therefore, data collected by the sensors positioned at the distance of 1200 and 1500 mm were used. The influence of load magnitude on the waves propagation was investigated via the different load force with approximately the same load time and vice versa. Expectations relating to the travel time of waves, depending on the differences of load impulse, were not met. The shorter travel time of waves was detected in the case of the lower frequencies. The use of load impulse magnitude as a possible explanation was not successful because opposite tendencies in travel time were noticed.


2015 ◽  
Vol 10 (2) ◽  
pp. 174-181 ◽  
Author(s):  
Nur Izzi Md. Yusoff ◽  
Sentot Hardwiyono ◽  
Norfarah Nadia Ismail ◽  
Mohd Raihan Taha ◽  
Sri Atmaja P. Rosyidi ◽  
...  

In pavement management systems, deflection basin tests, such as the Falling Weight Deflectometer test, are common techniques that are widely used, while the surface wave test, i.e. the Spectral Analysis of Surface Wave test, is recently employed as an alternative technique in pavement evaluation and monitoring. In this paper, the performance of both dynamic non-destructive tests on pavement subgrade investigation is presented. Surface wave propagation between a set of receivers was transformed into the frequency domain using the Fast Fourier Transform technique and subsequently a phase spectrum was produced to measure the time lag between receivers. Using the phase difference method, an experimental dispersion curve was generated. Inversion analysis based on the 3-D stiffness matrix method was then performed to produce a shear wave velocity profile. The elastic modulus of pavement layers was calculated based on linear elastic theory. In the Falling Weight Deflectometer test, seven geophones were used to collect in situ deflection data. Based on a back-calculation procedure with the ELMOD software, the elastic modulus of each flexible pavement layer can be obtained. Both techniques are able to comprehensively investigate the elastic modulus of the subgrade layer in existing pavement non-destructively. The elastic modulus between the Spectral Analysis of Surface Wave method and the Falling Weight Deflectometer test on the subgrade layer is observed to be in a good agreement. A correlation of the elastic modulus of thesubgrade layer from both techniques is also presented.


Sign in / Sign up

Export Citation Format

Share Document