scholarly journals Forming of Components with Microgearings from Coil Material—Numerical Modeling of the Process Chain and Experimental Validation

Micromachines ◽  
2021 ◽  
Vol 12 (12) ◽  
pp. 1456
Author(s):  
Andreas Rohrmoser ◽  
Martin Kraus ◽  
Marion Merklein
Keyword(s):  
Numerical Modeling ◽  
Mass Production ◽  
Size Effects ◽  
Experimental Validation ◽  
Process Chain ◽  
Cold Forming ◽  
Production Methods ◽  
Gear Teeth ◽  
Tool Stresses ◽  
Set Up

Compared to alternative production methods, cold forming offers technological, economic and ecological potential for the mass production of microgears. Within the current boundaries of the technology, the cold forming of modules m < 0.2 mm is not possible due to size effects, high tool stresses and handling problems. The investigations of this contribution present a novel process chain for the multi-step forming of microgears with a module of m = 0.1 mm. For this purpose, a numerical model of the first two steps of the process chain is set up and confirmed based on experimental forming tests. The results have proven the feasibility of the process chain by a complete forming of the gear teeth.

Microalgae Mass Production Methods

2009 ◽  
Vol 52 (4) ◽  
pp. 1275-1287 ◽  
Author(s):  
Y. Shen ◽  
W. Yuan ◽  
Z. J. Pei ◽  
Q. Wu ◽  
E. Mao
Keyword(s):  
Mass Production ◽  
Production Methods

Experimental Study of a Full Forward Extrusion Process from Metal Strip

2012 ◽  
Vol 504-506 ◽  
pp. 587-592 ◽  
Author(s):  
Marion Merklein ◽  
Tommaso Stellin ◽  
Ulf Engel
Keyword(s):  
Extrusion Process ◽  
Metal Strip ◽  
Raw Material ◽  
High Rate ◽  
Process Chain ◽  
Forward Extrusion ◽  
Bulk Forming ◽  
Material Conditions ◽  
Set Up ◽  
Tooling System

A high rate of production of complex microparts is increasingly required by fields like electronics and micromechanics. Handling is one of the main problems, limiting those forming processes of small metal components consisting of multiple forming stages. A forming chain in which a metal strip acts both as raw material and support of the workpiece through the different stages of the process, is seen as a solution that radically simplifies the positioning of microparts. Each workpiece stays connected to the strip through all the forming steps, being separated just at the end of the process chain. In this work, a tooling system for the bulk forming from copper strips has been set up and employed in a full forward extrusion process of a micro-billet. The same die, with a diameter of 1 mm, has been used with three different strip thicknesses (1, 2 and 3 mm) and three different material conditions. The use of thinner and hard-as-rolled strips has resulted in achieving a higher ratio of the billet length to strip thickness.

scholarly journals Measuring the bore straightness during reaming with sensoric tools

2020 ◽  
Vol 14 (4) ◽  
pp. 535-544
Author(s):  
Andreas Bretz ◽  
Eberhard Abele ◽  
Matthias Weigold
Keyword(s):  
Mass Production ◽  
Cost Efficiency ◽  
Machine Tools ◽  
Processing Time ◽  
Process Chain ◽  
Machining Processes ◽  
High Quality ◽  
Random Samples ◽  
Hydraulic Valves ◽  
Productive Time

Abstract Reaming plays a crucial role in production to meet the high quality requirements of precision bore machining. It is either directly responsible for the final component quality or influences subsequent processes such as honing. The narrow tolerances are usually monitored by measuring random samples in mass production due to cost efficiency. Having a closer look at an exemplary process chain for the production of hydraulic valves shows the possibility to adapt the honing parameters which reduces processing time and costs. However, the bore straightness after the reaming process has to be known. In this paper an approach is presented which allows to record the bore straightness within the productive time. For this purpose, a sensory reaming system is developed. It can be used without additional components in the machine tool and thus integrated into existing machining processes. Cutting tests show that the system is able to measure the bore straightness as good as sensing probes used in machine tools.

Sign in / Sign up

Export Citation Format

Share Document