scholarly journals Development of a Precise and High Response Pressure Regulator for Gases

2007 ◽  
Vol 38 (2) ◽  
pp. 29-34 ◽  
Author(s):  
Kenji KAWASHIMA ◽  
Tomonori KATO ◽  
Shunpei YAMAZAKI ◽  
Toshiharu KAGAWA
2010 ◽  
Vol 34 (1) ◽  
pp. 43-48 ◽  
Author(s):  
Tomonori Kato ◽  
Kenji Kawashima ◽  
Tatsuya Funaki ◽  
Kotaro Tadano ◽  
Toshiharu Kagawa

Author(s):  
Sasuga Ito ◽  
Masato Furukawa ◽  
Satoshi Gunjishima ◽  
Hiroki Usuki ◽  
Takafumi Ota ◽  
...  

Abstract Surge is an unsteady flow phenomenon occurring at low flow rates in the pipeline system including compressors. The surge is a phenomenon that must be avoided because of the danger in the operation: the pipeline equipment can be damaged or the operation cannot be continued. Experimental work is required not only to understand the unsteady behavior but to also validate the CFD used for more localized analysis and development of the understanding of the flow phenomena when operating near surge. Nevertheless, there are still many unclear points not only about the flow phenomenon at the inception of the surge which is important for the prediction of the surge but also about the surge behavior itself. Especially, as for the surge occurring in transonic centrifugal compressors, there are currently few experimental research cases due to the difficulty of the unsteady measurement. In this research, we measured the time variations in pressure and flow rate in a transonic centrifugal compressor for a vehicle turbocharger which consists of an impeller, vaneless diffuser and scroll. In the experiments, the measurement pipes were set upstream and downstream of the compressor and the velocity and the wall static pressure were measured with an I-type hot wire probe and high response pressure transducers, respectively. In addition, to investigate the process and the occurrence point of the back flow in surge, the wall static pressure was measured by means of high response pressure transducers which were mounted on the shroud upstream of the impeller and the diffuser hub at the two-circumferential positions, respectively. As the result of the experiments, the unsteady flow process during the mild and deep surges was measured and the inception of deep surge was clarified.


1986 ◽  
Vol 108 (1) ◽  
pp. 47-52 ◽  
Author(s):  
F. Sugeng ◽  
K. Fiedler

The unsteady flow problem in the axial compressor has been simulated in wind-tunnels by means of high-speed rotating cylinders upstream of the blade row. To obtain the dynamic changes in the flow properties 20 high-response pressure transducers and 20 high-response hot-film, which are embedded at the surface of the selected blade, have been used in connection with a periodic sampling and averaging technique in digital data acquisition and reduction. The fluctuating forces and the fluctuating drags acting on the blade due to passing wakes shedding through the blade row are carried out.


1995 ◽  
Vol 117 (4) ◽  
pp. 642-649 ◽  
Author(s):  
D. E. Van Zante ◽  
K. L. Suder ◽  
A. J. Strazisar ◽  
T. H. Okiishi

The aspirating probe originally designed by Epstein and Ng at MIT was modified by replacing the two platinum-coated tungsten hot wires normally used with platinum–iridium alloy wires. The resulting improved unsteady total pressure and total temperature resolution of the modified probe is demonstrated. Flowfield measurements were made downstream of NASA Rotor 37 for a part-speed operating condition to test the performance of the probe. Time-resolved blade-to-blade total temperature and total pressure as calculated from the two platinum–iridium hot-wire voltages are shown. The flowfield measurements are compared with independent measurements of total pressure with high response transducers and total temperature calculated from laser anemometer measurements. Limitations of a more often used unsteady temperature data reduction method, which involves only one aspirating probe hot-wire voltage and a high-response pressure measurement, are discussed.


Author(s):  
Dale E. Van Zante ◽  
Kenneth L. Suder ◽  
Anthony J. Strazisar ◽  
Theodore H. Okiishi

The aspirating probe originally designed by Epstein and Ng at MIT was modified by replacing the two platinum coated tungsten hot wires normally used with platinum iridium alloy wires. The resulting improved unsteady total pressure and total temperature resolution of the modified probe is demonstrated. Flowfield measurements were made downstream of NASA Rotor 37 for a part speed operating condition to test the performance of the probe. Time resolved blade-to-blade total temperature and total pressure as calculated from the two platinum iridium hot wire voltages are shown. The flowfield measurements are compared with independent measurements of total pressure with high response transducers and total temperature calculated from laser anemometer measurements. Limitations of a more often used unsteady temperature data reduction method which involves only one aspirating probe hot wire voltage and a high-response pressure measurement are discussed.


1983 ◽  
Vol 105 (1) ◽  
pp. 204-211 ◽  
Author(s):  
A. P. Kurkov

Stationary high-response pressure and displacement measurements are used to describe the flutter characteristics of the first fan-rotor of a turbofan engine. Flutter occurred at part speed and at high incidence. Several forward and backward traveling waves were identified in a predominantly torsional flutter mode. Positive aerodynamic work contribution was confined to the region close to the leading edge and was mainly due to modes corresponding to forward traveling waves of nodal diameters in the range 3 to 5.


Sign in / Sign up

Export Citation Format

Share Document