scholarly journals Numerical Study of Spray Characteristics of n-Heptane in Constant Volume Combustion Chamber under Diesel Engine Conditions

2016 ◽  
Vol 27 (6) ◽  
pp. 727-736
Author(s):  
SHUBHRA KANTI DAS ◽  
OCKTAECK LIM
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Numerical Study ◽  
Constant Volume ◽  
Spray Characteristics ◽  
Constant Volume Combustion ◽  
Constant Volume Combustion Chamber

Experimental and numerical study of cyclic variations in a Constant Volume Combustion chamber

2016 ◽  
Vol 172 ◽  
pp. 49-61 ◽  
Author(s):  
Laure Labarrere ◽  
Thierry Poinsot ◽  
Antoine Dauptain ◽  
Florent Duchaine ◽  
Marc Bellenoue ◽  
...  
Keyword(s):  
Combustion Chamber ◽  
Numerical Study ◽  
Constant Volume ◽  
Constant Volume Combustion ◽  
Constant Volume Combustion Chamber ◽  
Cyclic Variations

Numerical investigation of oil droplet combustion using single particle ignition cell model

2020 ◽  
pp. 146808741989693
Author(s):  
Ankith Ullal ◽  
Youngchul Ra ◽  
Jeffrey D Naber ◽  
William Atkinson ◽  
Satoshi Yamada ◽  
...  
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Structural Damage ◽  
Internal Combustion Engines ◽  
Initial Conditions ◽  
Numerical Study ◽  
Constant Volume ◽  
Oil Droplet ◽  
Constant Volume Combustion ◽  
Constant Volume Combustion Chamber

Pre-ignition in internal combustion engines is an abnormal combustion phenomenon which often results in structural damage to the engine. It occurs when an ignition event takes place in the combustion chamber before the designed ignition time. In this work, a numerical study was done to investigate the pre-ignition with potential application to natural gas marine engines. This was done by simulating experiments of lube oil–induced ignition and subsequent combustion in a constant volume combustion chamber using an in-house version of the KIVA4-CFD code. Initial conditions of the chamber gases are obtained from the pre-burn process of a known composition of C2H2/oxidizer mixture. Natural gas was injected from a single-hole injector at an injection temperature and pressure of 300 K and 105 Pa, respectively. A rotating fan was modeled, as is in the experimental setup. Oil droplet of known size and velocity is injected into the constant volume combustion chamber. For accurate prediction of oil droplet ignition, the computational cells that contain the droplets are to be refined. Combustion calculations are then carried out on the refined grid. Ignition delay times of both lube oil and methane/air mixtures were calculated. Parametric studies were also conducted by varying droplet conditions, and their results are also presented.

scholarly journals Numerical Study on Direct Injection of Hydrogen-Methane Blends into a Constant Volume Combustion Chamber

2019 ◽  
Author(s):  
Mohammadrasool Morovatiyan ◽  
Martia Shahsavan ◽  
John Hunter Mack
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Volume Fraction ◽  
Numerical Study ◽  
Computational Study ◽  
Constant Volume ◽  
Chamber Pressure ◽  
Compression Ignition ◽  
Constant Volume Combustion ◽  
Constant Volume Combustion Chamber

Natural gas is not commonly used in compression ignition cycles due to difficulty in achieving autoignition conditions. The addition of hydrogen to natural gas can help overcome this issue considering hydrogen’s flammability range and ability to autoignite. In this computational study, the turbulent injection of hydrogen-methane mixtures with varied composition of the gaseous fuels into a constant volume combustion chamber has been modeled. All conditions including injection pressure, initial chamber temperature, and initial chamber pressure are kept constant; the jet properties and combustion characteristics were then investigated. The results indicate that adding hydrogen to methane drastically shortens the ignition delay, enables the system to run at a lower initial temperature, and provides appropriate conditions for the compression ignition of the gaseous fuel. Increasing the volume fraction of hydrogen in the mixture strongly affects the spray tip penetration length and cone angle, while altering the mixing rate of the injected fuel with air. The mixtures with higher hydrogen volume fractions penetrate more during the early stages of injection. However, the higher momentum of the mixtures with more methane compensates for this effect when the jet disperses significantly in the chamber.

Comparison of Ethanol and Butanol as Additives in Soybean Biodiesel Using a Constant Volume Combustion Chamber

2011 ◽  
Vol 25 (5) ◽  
pp. 2426-2426 ◽  
Author(s):  
Haifeng Liu ◽  
Chia-fon F. Lee ◽  
Ming Huo ◽  
Mingfa Yao
Keyword(s):  
Combustion Chamber ◽  
Constant Volume ◽  
Soybean Biodiesel ◽  
Constant Volume Combustion ◽  
Constant Volume Combustion Chamber
Sign in / Sign up

Export Citation Format

Share Document