An Investigation Work on Heat Transfer and Friction Factor Characteristics of Thermosyphon Solar Water Heater System Fitted With Spacer at the Trailing Edge of Twisted Tapes

2012 ◽  
Vol 3 (4) ◽  
pp. 44-51
Author(s):  
S. Senthil Kumar
Keyword(s):  
Heat Transfer ◽  
Friction Factor ◽  
Solar Water Heater ◽  
Water Heater ◽  
Trailing Edge ◽  
Solar Water ◽  
Twisted Tapes

scholarly journals Parametric optimization of a stamped longitudinal vortex generator inside a circular tube of a solar water heater at low Reynolds numbers

2021 ◽  
Vol 3 (8) ◽  
Author(s):  
Felipe A. S. Silva ◽  
Luis Júnior ◽  
José Silva ◽  
Sandilya Kambampati ◽  
Leandro Salviano
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Reynolds Numbers ◽  
Geometric Parameters ◽  
Vortex Generators ◽  
Longitudinal Vortex ◽  
Solar Water Heater ◽  
Water Heater ◽  
Solar Water

AbstractSolar Water Heater (SWH) has low efficiency and the performance of this type of device needs to be improved to provide useful and ecological sources of energy. The passive techniques of augmentation heat transfer are an effective strategy to increase the convective heat transfer coefficient without external equipment. In this way, recent investigations have been done to study the potential applications of different inserts including wire coils, vortex generators, and twisted tapes for several solar thermal applications. However, few researchers have investigated inserts in SWH which is useful in many sectors where the working fluid operates at moderate temperatures. The longitudinal vortex generators (LVG) have been applied to promote heat transfer enhancement with a low/moderate pressure drop penalty. Therefore, the present work investigated optimal geometric parameters of LVG to enhance the heat transfer for a SWH at low Reynolds number and laminar flow, using a 3D periodical numerical simulation based on the Finite Volume Method coupled to the Genetic Algorithm optimization method (NSGA-II). The LVG was stamped over a flat plate inserted inside a smooth tube operating under a typical residential application corresponding to Reynolds numbers of 300, 600, and 900. The geometric parameters of LGV were submitted to the optimization procedure which can find traditional LVG such as rectangular-winglet and delta-winglet or a mix of them. The results showed that the application of LGVs to enhance heat transfer is an effective passive technique. The different optimal shapes of the LVG for all Reynolds numbers evaluated improved more than 50% of heat transfer. The highest augmentation heat transfer of 62% is found for the Reynolds number 900. However, the best thermo-hydraulic efficiency value is found for the Reynolds number of 600 in which the heat transfer intensification represents 55% of the pressure drop penalty.

Second-Law Analysis of a Two-Phase Self-Pumping Solar Water Heater

1992 ◽  
Vol 114 (3) ◽  
pp. 188-193 ◽  
Author(s):  
H. A. Walker ◽  
J. H. Davidson
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Hot Water ◽  
Solar Water Heater ◽  
Total Entropy ◽  
Water Heating ◽  
Water Heater ◽  
Two Phase ◽  
Solar Water ◽  
Order Of Magnitude

Entropy generated by operation of a two-phase self-pumping solar water heater under Solar Rating and Certification Corporation rating conditions is computed numerically in a methodology based on an exergy cascade. An order of magnitude analysis shows that entropy generation is dominated by heat transfer across temperature differences. Conversion of radiant solar energy incident on the collector to thermal energy within the collector accounts for 87.1 percent of total entropy generation. Thermal losses are responsible for 9.9 percent of total entropy generation, and heat transfer across the condenser accounts for 2.4 percent of the total entropy generation. Mixing in the tempering valve is responsible for 0.7 percent of the total entropy generation. Approximately one half of the entropy generated by thermal losses is attributable to the self-pumping process. The procedure to determine total entropy generation can be used in a parametric study to evaluate the performance of two-phase hot water heating systems relative to other solar water heating options.

Sign in / Sign up

Export Citation Format

Share Document