Research and Test of Three-Pulley Noncircular Synchronous Pulley Transmission Mechanism with Minimum Slack

The noncircular synchronous belt drive mechanism has demonstrated certain achievements and has been used in special fields. Research regarding noncircular synchronous belt drive mechanisms has focused on optimization design and kinematic analysis in China, whereas two pulley noncircular synchronous belt transmissions have been developed overseas. However, owing to the noncircular characteristics of the belt pulley, the real-time variation in the belt length slack during the transmission of the noncircular synchronous belt is significant, resulting in high probabilities of skipping and vibration. In this study, a noncircular tensioning pulley is added to create a stable three-pulley noncircular synchronous belt driving mechanism and a good synchronous belt tensioning, with no skipping; hence, the non-uniform output characteristic of the driven pulley is consistent with the theoretical value. In the circular noncircular noncircular three-pulley noncircular synchronous belt mechanism, the pitch curve of the driving synchronous belt pulley is circular, whereas those of the driven synchronous belt and tensioning pulleys are noncircular. To minimize the slack of the belt length of the synchronous belt and the constraint of the concavity and circumference of the tensioning pulley, an automatic optimization model of the tensioning pulley pitch curve is established. The motion simulation, analysis, and optimization code for a three-belt-pulley noncircular synchronous belt drive mechanism is written, and the variation in belt length slack under different speed ratios is analyzed based on several examples. The testbed for a circular–noncircular–noncircular three-pulley noncircular synchronous belt transmission mechanism is developed. The test shows that the three-pulley noncircular synchronous belt drives well. This study proposes an automatic optimization algorithm for the tensioning pulley pitch curve of a noncircular synchronous belt transmission mechanism; it yields a stable transmission of the noncircular synchronous belt transmission mechanism as well as non-uniform output characteristics.

Transmission Error Due to Resonance in Synchronous Belt Drive With Eccentric Pulley

In synchronous belt drives, it is generally difficult to eliminate pulley eccentricity, because the pulley teeth and shaft hole are produced separately and the pulley is installed on an eccentric shaft. This eccentricity affects the accuracy of rotation transmission, so that the belt tension changes during a single rotation of the pulley. This in turn affects the occurrence of resonance in the spans. In the present study, the transmission error in a synchronous belt drive with an eccentric pulley in the absence of a transmitted load was experimentally investigated for the case in which the spans undergo first-mode transverse vibration due to resonance. The transmission error was found to have a component with a period equal to the span displacement, in addition to a component with a period of half the span displacement. During a single rotation of the pulley, the magnitude of the transmission error increased, and its frequency decreased, with decreasing belt tension. The transmission error exhibited the large value when two frequency conditions were satisfied: one was that the meshing frequency was within the range of span frequency variations due to the eccentricity, and the other was that the minimum span frequency was close to an integer multiple of the pulley rotation frequency. Even if both of these conditions occurred, if the range of span frequency variations due to the eccentricity was larger than 13 Hz, the transmission error could be eliminated by adjusting the belt tension, so that the average span frequency corresponded to the meshing frequency.

Transmission Error due to Resonance in Synchronous Belt Drive With Eccentric Pulley

In synchronous belt drives, it is generally difficult to eliminate pulley eccentricity, because the pulley teeth and shaft hole are produced separately. This eccentricity affects the accuracy of rotation transmission, so that the belt tension changes during a single rotation of the pulley. This in turn affects the occurrence of resonance in the spans. In the present study, the transmission error in a synchronous belt drive with an eccentric pulley in the absence of a transmitted load was experimentally investigated for the case in which the spans undergo first-mode transverse vibration due to resonance. The transmission error was found to have a component with a period equal to the displacement of the span, in addition to a component with a period of half the displacement of the span. During a single rotation of the pulley, the magnitude of the transmission error increased, and its frequency decreased, with decreasing belt tension. The transmission error exhibited the large value when two frequency conditions were satisfied: one was that the meshing frequency was within the range of span frequency variations due to the eccentricity, and the other was that the minimum frequency of the span was close to an integer multiple of the rotation frequency of the pulley. Even if both of these conditions occurred, if the range of span frequency variations due to the eccentricity was larger than 13 Hz, the transmission error could be eliminated by adjusting the belt tension so that the average frequency of the span corresponded to the meshing frequency.