Sub-Critical Crack Growth, Surface Energy and Fracture Toughness of Brittle Materials

1986 ◽  
pp. 255-272 ◽  
Author(s):  
Daniel Maugis
Keyword(s):  
Fracture Toughness ◽  
Surface Energy ◽  
Crack Growth ◽  
Brittle Materials ◽  
Growth Surface ◽  
Critical Crack

scholarly journals Fracture toughness and crack growth of brackish ice using chevron-notched specimens

1994 ◽  
Vol 40 (135) ◽  
pp. 415-426
Author(s):  
Lars Stehn
Keyword(s):  
Fracture Toughness ◽  
Crack Growth ◽  
Crack Opening ◽  
Initial Crack ◽  
Effect Study ◽  
Small Scale ◽  
Opening Displacement ◽  
Critical Crack ◽  
Experimental Calibration ◽  
Brackish Ice

AbstractField-test equipment called FIFT (a Field Instrument for Fracture toughness Tests on ice) was used in both field and laboratory fracture-toughness tests on brackish sea ice from the Gulf of Bothnia. An experimental calibration was performed and a compliance expression was then derived for the Short Rod Chevron Notched (SRCN) specimen. Using the SRCN configuration, for which the initial crack growth is shown to be stable, and measured load-point displacements, preliminary crack-growth velocities are found. The obtained estimated crack velocity is, on average,ȧe= 20 ms−1, albeit with a large standard deviation. The results indicate that critical crack (crack-jumping) growth occurs. The apparent fracture toughness,KQ, was found to have a pronounced dependency on porosity in the form of brine volume. The results obtained are derived from a linearly elastic fracture mechanics (LEFM) theory. Consequently, the tests were designed to satisfy small-scale yielding requirements in terms of notch sensitivity and brittleness. The linearity of the load vs crack-opening displacement curves together with a size-effect study, showing that the specimen is notch-sensitive for grain-sizes ranging from 1.6 to nearly 100 mm, indicate that LEFM could be applicable.

scholarly journals Fracture toughness and crack growth of brackish ice using chevron-notched specimens

1994 ◽  
Vol 40 (135) ◽  
pp. 415-426 ◽  
Author(s):  
Lars Stehn
Keyword(s):  
Fracture Toughness ◽  
Crack Growth ◽  
Crack Opening ◽  
Initial Crack ◽  
Effect Study ◽  
Small Scale ◽  
Opening Displacement ◽  
Critical Crack ◽  
Experimental Calibration ◽  
Brackish Ice

AbstractField-test equipment called FIFT (a Field Instrument for Fracture toughness Tests on ice) was used in both field and laboratory fracture-toughness tests on brackish sea ice from the Gulf of Bothnia. An experimental calibration was performed and a compliance expression was then derived for the Short Rod Chevron Notched (SRCN) specimen. Using the SRCN configuration, for which the initial crack growth is shown to be stable, and measured load-point displacements, preliminary crack-growth velocities are found. The obtained estimated crack velocity is, on average,ȧe= 20 ms−1, albeit with a large standard deviation. The results indicate that critical crack (crack-jumping) growth occurs. The apparent fracture toughness,KQ, was found to have a pronounced dependency on porosity in the form of brine volume. The results obtained are derived from a linearly elastic fracture mechanics (LEFM) theory. Consequently, the tests were designed to satisfy small-scale yielding requirements in terms of notch sensitivity and brittleness. The linearity of the load vs crack-opening displacement curves together with a size-effect study, showing that the specimen is notch-sensitive for grain-sizes ranging from 1.6 to nearly 100 mm, indicate that LEFM could be applicable.

Influence of subcritical crack growth on the determination of fracture toughness in brittle materials

2016 ◽  
Vol 36 (5) ◽  
pp. 1307-1312 ◽  
Author(s):  
C. Krautgasser ◽  
Z. Chlup ◽  
P. Supancic ◽  
R. Danzer ◽  
R. Bermejo
Keyword(s):  
Fracture Toughness ◽  
Crack Growth ◽  
Subcritical Crack Growth ◽  
Brittle Materials

A macroscopic theory of microcrack growth in brittle materials

1991 ◽  
Vol 335 (1639) ◽  
pp. 455-485 ◽  
Keyword(s):  
Crack Growth ◽  
Brittle Materials ◽  
Macroscopic Theory ◽  
Rate Of Increase ◽  
Inelastic Behaviour ◽  
Constitutive Response ◽  
Macroscopic Plasticity ◽  
Microcrack Growth ◽  
Vector Valued

This paper is concerned with the development of a macroscopic theory of crack growth in fairly brittle materials. Average characteristics of the cracks are described in terms of an additional vector-valued variable in the macroscopic theory, which is determined by an additional momentum-like balance law associated with the rate of increase of the area of the cracks and includes the effects of forces maintaining the crack growth and the inertia of microscopic particles surrounding the cracks. The basic developments represent an idealized characterization of inelastic behaviour in the presence of crack growth, which accounts for energy dissipation without explicit use of macroscopic plasticity effects. A physically plausible constraint on the rate of crack growth is adopted to simplify the theory. To ensure that the results of the theory are physically reasonable, the constitutive response of the dependent variables are significantly restricted by consideration both of the energetic effects and of the microscopic processes that give rise to crack growth. These constitutive developments are in conformity with many of the standard results and observations reported in the literature on fracture mechanics. The predictive nature of the theory is illustrated with reference to two simple examples concerning uniform extensive and compressive straining.

The Fracture Toughness of Hardened Tool Steels

1987 ◽  
Vol 109 (4) ◽  
pp. 314-318 ◽  
Author(s):  
D. F. Watt ◽  
Pamela Nadin ◽  
S. B. Biner
Keyword(s):  
Fracture Toughness ◽  
Crack Growth ◽  
Slow Crack Growth ◽  
Crack Opening ◽  
Compact Tension ◽  
Testing Procedure ◽  
Tool Steels ◽  
Opening Displacement ◽  
Tempering Temperature ◽  
Toughness Testing

This report details the development of a three-stage fracture toughness testing procedure used to study the effect of tempering temperature on toughness in 01 tool steel. Modified compact tension specimens were used in which the fatigue precracking stage in the ASTM E-399 Procedure was replaced by stable precracking, followed by a slow crack growth. The specimen geometry has been designed to provide a region where slow crack growth can be achieved in brittle materials. Three parameters, load, crack opening displacement, and time have been monitored during the testing procedure and a combination of heat tinting and a compliance equation have been used to identify the position of the crack front. Significant KIC results have been obtained using a modified ASTM fracture toughness equation. An inverse relationship between KIC and hardness has been measured.

Automated Control of Stable Crack Growth for R-Curve Measurements in Brittle Materials

2012 ◽  
Vol 53 (2) ◽  
pp. 163-170 ◽  
Author(s):  
H. Jelitto ◽  
F. Hackbarth ◽  
H. Özcoban ◽  
G. A. Schneider
Keyword(s):  
Crack Growth ◽  
Brittle Materials ◽  
Stable Crack Growth ◽  
Automated Control
Sign in / Sign up

Export Citation Format

Share Document