Simplified equations for determining double-k fracture parameters of concrete for compact tension test

Polynomial equations in non-dimensional form for various fracture parameters of double-K fracture model for compact tension specimen have been derived and presented in this paper. These equations can be used for computing different double-K fracture parameters of concrete for known material properties and specimen size having relative size of initial crack length of 0.3 without involving much complexity in numerical computations. Values of peak load and corresponding crack opening displacement as necessary to compute the double-K fracture parameters of concrete have been derived from the established fictitious crack model in the present study. A simplified equation in non-dimensional form between peak load and critical crack opening displacement as obtained from a fictitious crack model has also been presented.

Elastic-plastic fracture analysis of anisotropy effect on AA2050-T84 alloy at different temperatures: A Numerical Study

The third generation Al-Li alloy AA2050-T84 is widely used in aircraft applications due to its lightweight and significant mechanical properties. The anisotropic variations of tensile and compression properties of this alloy at various temperatures are substantial. In this work, the variations of the J-integral, CTOD, and Plastic Zone Size (PZS) due to anisotropy of a 4-inch thick AA2050-T84 plate at ambient and cryogenic temperatures were studied numerically by using Compact Tension (C(T)) specimen. The material anisotropy resulted in fracture and constraint parameter variation for Mode-I constant load. Numerical results indicated a decrease in crack driving forces and a constraint parameter with the decrease in temperature at the plate surface and central location. Plate surface locations appear to be isotropic for both temperatures under elastic-plastic fracture analyses as crack driving forces were almost identical. The temperature effect is more on constraint as the normalized PZS values at ambient temperature have been twice that of cryogenic temperature. The isotropic behavior of a plate under sub-zero temperature makes the plate suitable for cryogenic temperature applications.

The study of redistribution in residual stresses during fatigue crack growth

Numerical and experimental study was conducted on fatigue crack growth (FCG) of metallic components to investigate the redistribution of mechanical residual stresses during FCG. To this end, the compact tension specimens of an aluminium alloy were used. In addition, mechanical residual stresses were introduced near the crack tip by applying compressive and tensile loads, followed by visually observing the side-surface of the specimens to estimate the crack growth length. In the numerical simulation, cyclic J-integral was used as the crack growth fracture parameter and a good agreement was observed between the numerical and experimental results. The results of the finite element method demonstrated a clear redistribution of mechanical residual stresses during FCG. After a few cycles, the residual stress field around the crack tip reached a lower magnitude value confined in a smaller zone, although this zone was stable during the remaining fatigue process. Finally, present study evaluated the effect of stress ratio, load amplitude, and initial residual stresses level on the redistribution of residual stresses. It was observed that the residual stresses are mainly released during the first steps of fatigue loading.

Estimation of C* Integral for Mismatched Welded Compact Tension Specimen

The C* integral for the compact tension (CT) specimen is calculated using the estimation equation in ASTM E1457-15. This equation was developed based on the assumption of material homogeneity and is not applicable to a welded CT specimen. In this paper, a modified equation for estimating the C* integral for a welded compact tension (CT) specimen under creep conditions is proposed. The proposed equation is defined on the basis of systematically conducted extensive finite element (FE) analyses using the ABAQUS program. A crack in the welded CT specimen is located in the center of the heat-affected zone (HAZ), because the most severe type IV cracks are located in the HAZ. The results obtained by the analysis show that the equation for estimating the C* integral in ASTM E1457-15 can underestimate the value of the C* integral for creep-soft HAZ and overestimate for creep-hard HAZ. Therefore, the proposed modified equation is suitable for describing the creep crack growth (CCG) of welded specimens.

Influence of 3D Printing Topology by DMLS Method on Crack Propagation

The presented text deals with research into the influence of the printing layers’ orientation on crack propagation in an AlSi10Mg material specimen, produced by additive technology, using the Direct Metal Laser Sintering (DMLS) method. It is a method based on sintering and melting layers of powder material using a laser beam. The material specimen is presented as a Compact Tension test specimen and is printed in four different defined orientations (topology) of the printing layers—0°, 45°, 90°, and twice 90°. The normalized specimen is loaded cyclically, where the crack length is measured and recorded, and at the same time, the crack growth rate is determined. The evaluation of the experiment shows an apparent influence of the topology, which is essential especially for possible use in the design and technical preparation of the production of real machine parts in industrial practice. Simultaneously with the measurement results, other influencing factors are listed, especially product postprocessing and the measurement method used. The hypothesis of crack propagation using Computer Aided Engineering/Finite Element Method (CAE/FEM) simulation is also stated here based on the achieved results.

Impact of Enzymatic Degradation on the Material Properties of Poly(Ethylene Terephthalate)

With macroscopic litter and its degradation into secondary microplastic as a major source of environmental pollution, one key challenge is understanding the pathways from macro- to microplastic by abiotic and biotic environmental impact. So far, little is known about the impact of biota on material properties. This study focuses on recycled, bottle-grade poly(ethylene terephthalate) (r-PET) and the degrading enzyme PETase from Ideonella sakaiensis. Compact tension (CT) specimens were incubated in an enzymatic solution and thermally and mechanically characterized. A time-dependent study up to 96 h revealed the formation of steadily growing colloidal structures. After 96 h incubation, high amounts of BHET dimer were found in a near-surface layer, affecting crack propagation and leading to faster material failure. The results of this pilot study show that enzymatic activity accelerates embrittlement and favors fragmentation. We conclude that PET-degrading enzymes must be viewed as a potentially relevant acceleration factor in macroplastic degradation.