Experimental Investigations of Active Flow Control Using a Piezo Adaptive Blade in a Compressor Cascade Under Periodic Boundary Conditions with High Strouhal-Number

2021 ◽  
pp. 305-320
Author(s):  
Tobias Werder ◽  
Lukas Kletschke ◽  
Robert Liebich
Keyword(s):  
Boundary Conditions ◽  
Flow Control ◽  
Strouhal Number ◽  
Periodic Boundary ◽  
Active Flow Control ◽  
Periodic Boundary Conditions ◽  
Experimental Investigations ◽  
Compressor Cascade ◽  
Active Flow

Experimental Investigations on the Efficiency of Active Flow Control in a Compressor Cascade With Periodic Non-Steady Outflow Conditions

2017 ◽  
Author(s):  
Marcel Staats ◽  
Wolfgang Nitsche
Keyword(s):  
Flow Field ◽  
Flow Control ◽  
Flow Separation ◽  
Active Flow Control ◽  
Experimental Investigations ◽  
Compressor Cascade ◽  
Steady Regime ◽  
Stator Blade ◽  
Active Flow ◽  
The Impact

We present results of experiments on a periodically unsteady compressor stator flow of the type which would be expected in consequence of pulsed combustion. A Reynolds number of Re = 600000 was used for the investigations. The experiments were conducted on the two-dimensional low-speed compressor testing facility in Berlin. A choking device downstream the trailing edges induced a periodic non-steady outflow condition to each stator vane which simulated the impact of a pressure gaining combuster downstream from the last stator. The Strouhal number of the periodic disturbance was Sr = 0.03 w.r.t. the stator chord length. Due to the periodic non-steady outflow condition, the flow-field suffers from periodic flow separation phenomena, which were managed by means of active flow control. In our case, active control of the corner separation was applied using fluidic actuators based on the principle of fluidic amplification. The flow separation on the centre region of the stator blade was suppressed by means of a fluidic blade actuator leading to an overall time-averaged loss reduction of 11.5%, increasing the static pressure recovery by 6.8% while operating in the non-steady regime. Pressure measurements on the stator blade and the wake as well as PIV data proved the beneficial effect of the active flow control application to the flow field and the improvement of the compressor characteristics. The actuation efficiency was evaluated by two figures of merit introduced in this contribution.

Active Flow Control Utilizing an Adaptive Blade Geometry and an Extremum Seeking Algorithm at Periodically Transient Boundary Conditions

2021 ◽  
Vol 143 (2) ◽  
Author(s):  
Tobias Werder ◽  
Robert Liebich ◽  
Karl Neuhäuser ◽  
Clara Behnsen ◽  
Rudibert King
Keyword(s):  
Phase Shift ◽  
Flow Control ◽  
Gas Turbines ◽  
Active Flow Control ◽  
Operating Conditions ◽  
Extremum Seeking ◽  
Experimental Investigations ◽  
Compressor Cascade ◽  
Active Flow ◽  
The Impact

Abstract As a consequence of constant volume combustion in gas turbines, pressure waves propagating upstream the main flow into the compressor system are generated leading to incidence variations. Numerical and experimental investigations of stator vanes have shown that active flow control (AFC) by means of adaptive blade geometries is beneficial when such periodic incidence variations occur. A significant risk reduction in a compressor facing disturbances can thereby be achieved concerning stall or choke. Experimental investigations on such an AFC method with simultaneous application of a closed-loop control are missing in order to demonstrate its potential. This work investigates a linear compressor cascade that is equipped with a 3D-manufactured piezo-adaptive blade structure. The utilized actuators are piezoelectric macro-fiber-composites. A throttling device is positioned downstream the trailing edge plane to emulate an unsteady combustion process. Periodic transient throttling events with a frequency of up to 20 Hz cause incidence changes to the blade’s leading edge. Consequently, pressure fluctuations on the blade’s surface occur, having a significant impact on the pressure recovery downstream of the stator cascade. Experimental results of harmonically actuating the piezo-adaptive blade with the corresponding disturbance frequency show that the impact of disturbances can be reduced to approximately 50%. However, this is only effective if the phase shift of the harmonic actuation is adjusted correctly. Using an inadequate phase shift reverses the positive effects, causing the aforementioned stall, choke, or significant losses. In order to find the optimum phase shift, even under varying, possibly unpredictable operating conditions, an extremum seeking controller is presented. This gradient-based approach is minimizing the pressure variance over time by carefully adjusting the phase shift of the harmonic actuation of the AFC system.

Active Flow Control Utilizing an Adaptive Blade Geometry and an Extremum Seeking Algorithm at Periodically Transient Boundary Conditions

2020 ◽  
Author(s):  
Tobias Werder ◽  
Robert Liebich ◽  
Karl Neuhäuser ◽  
Clara Behnsen ◽  
Rudibert King
Keyword(s):  
Phase Shift ◽  
Flow Control ◽  
Gas Turbines ◽  
Active Flow Control ◽  
Operating Conditions ◽  
Extremum Seeking ◽  
Experimental Investigations ◽  
Compressor Cascade ◽  
Active Flow ◽  
The Impact

Abstract As a consequence of constant volume combustion in gas turbines pressure waves propagating upstream the main flow into the compressor system are generated leading to incidence variations. Numerical and experimental investigations of stator vanes have shown that Active Flow Control (AFC) by means of adaptive blade geometries is beneficial when such periodic incidence variations occur. A significant risk reduction in a compressor facing disturbances can thereby be achieved concerning stall or choke. Experimental investigations on such an AFC method with simultaneous application of a closed-loop control are missing in order to demonstrate its potential. This work investigates a linear compressor cascade that is equipped with a 3D-manufactured piezo adaptive blade structure. The utilized actuators are piezoelectric Macro-Fiber-Composites. A throttling device is positioned downstream the trailing edge plane to emulate an unsteady combustion process. Periodic transient throttling events with a frequency of up to 20 Hz cause incidence changes to the blade’s leading edge. Consequently, pressure fluctuations on the blade’s surface occur, having a significant impact on the pressure recovery downstream of the stator cascade. Experimental results of harmonically actuating the piezo adaptive blade with the corresponding disturbance frequency show that the impact of disturbances can be reduced to approx. 50 %. However, this is only effective if the phase shift of the harmonic actuation is adjusted correctly. Using an inadequate phase shift reverses the positive effects, causing the aforementioned stall, choke, or significant losses. In order to find the optimum phase shift, even under varying, possibly unpredictable operating conditions, an Extremum Seeking Controller is presented. This gradient-based approach is minimizing the pressure variance over time by carefully adjusting the phase shift of the harmonic actuation of the AFC system.

scholarly journals Active flow control by means of synthetic jets on a highly loaded compressor cascade

2011 ◽  
Vol 225 (7) ◽  
pp. 897-908 ◽  
Author(s):  
V Zander ◽  
M Hecklau ◽  
W Nitsche ◽  
A Huppertz ◽  
M Swoboda
Keyword(s):  
Flow Control ◽  
Large Scale ◽  
Active Flow Control ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Experimental Investigations ◽  
Compressor Cascade ◽  
Actuation Frequency ◽  
Active Flow ◽  
Highly Loaded

This article presents the potential of active flow control to increase the aerodynamic performance of highly loaded turbomachinery compressor blades. Experimental investigations on a large-scale compressor cascade equipped with 30 synthetic jet actuators mounted to the sidewalls and the blades themselves have been carried out. Results for a variation of the inflow angle, the jet amplitude, and the actuation frequency are presented. The wake measurements show total pressure loss reductions of nearly 10 per cent for the synthetic jet actuation. An efficiency calculation reveals that the energy saved by actuation is nearly twice the energy consumption of the synthetic jets.

Organization of Cylinder Wake Using a Splitter-Plate Active Flow Control

2010 ◽  
Author(s):  
Chris Weiland ◽  
Pavlos Vlachos
Keyword(s):  
Circular Cylinder ◽  
Flow Control ◽  
Strouhal Number ◽  
Active Flow Control ◽  
Leading Edge ◽  
Splitter Plate ◽  
Cylinder Wake ◽  
Time Resolved ◽  
Image Velocimetry ◽  
Active Flow

Time Resolved Digital Particle Image Velocimetry (TRDPIV) was used in conjunction with spectral analysis to study the effects of Leading Edge Blowing (LEB) flow control on the near-wake of a circular cylinder. The airfoil was placed 1.9 circular cylinder diameters downstream, effectively acting as a splitter plate. Spectral measurements of the TRDPIV results indicated that the presence of the airfoil decreased the Strouhal number from 0.19 to 0.12 as anticipated. When activated the LEB jet organized the circular cylinder wake, effectively neutralizing the effect of the splitter plate and modifying the wake so as to return the Strouhal number to 0.19. Thus the circular cylinder wake returned to its normal shedding frequency, even in the presence of the airfoil. Evidence presented in this study supports the notion that the LEB jet directly excites the circular cylinder shear layers causing instability, roll up, and subsequent vortex shedding.

Numerical Investigations of the Efficiency of Circulation Control in a Compressor Stator

2011 ◽  
Vol 134 (2) ◽  
Author(s):  
Arne Vorreiter ◽  
Susanne Fischer ◽  
Horst Saathoff ◽  
Rolf Radespiel ◽  
Joerg R. Seume
Keyword(s):  
Flow Control ◽  
High Speed ◽  
Design Method ◽  
Active Flow Control ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Circulation Control ◽  
Compressor Cascade ◽  
First Results ◽  
Active Flow

Airfoil active flow control has been attempted in the past in order to increase the permissible loading of boundary layers in gas turbine components. The present paper presents a stator with active flow control for a high-speed compressor using a Coanda surface near the trailing edge in order to inhibit boundary layer separation. The design intent is to reduce the number of vanes while—in order to ensure a good matching with the downstream rotor—the flow turning angle is kept constant. In a first step, numerical simulations of a linear compressor cascade with circulation control are conducted. The Coanda surface is located behind an injection slot on the airfoil suction side. Small blowing rates lead to a gain in efficiency associated with a rise in static pressure. In a second step, this result is transferred to a four-stage high-speed research compressor, where the circulation control is applied in the first stator. The design method and the first results are based on steady numerical calculations. The analysis of these results shows performance benefits of the concept. For both the cascade and the research compressor, the pressure gain and efficiency are shown as a function of blowing rate and jet power ratio. The comparison is performed based on a dimensionless efficiency, which takes into account the change in power loss.

Particle image velocimetry of active flow control on a compressor cascade

2010 ◽  
Vol 50 (4) ◽  
pp. 799-811 ◽  
Author(s):  
M. Hecklau ◽  
R. van Rennings ◽  
V. Zander ◽  
W. Nitsche ◽  
A. Huppertz ◽  
...  
Keyword(s):  
Particle Image Velocimetry ◽  
Flow Control ◽  
Particle Image ◽  
Active Flow Control ◽  
Compressor Cascade ◽  
Image Velocimetry ◽  
Active Flow
Sign in / Sign up

Export Citation Format

Share Document