Mechanical Response and Energy Stored During Deformation of Crystallizing TPU

Residual Stress, Thermomechanics & Infrared Imaging, Hybrid Techniques and Inverse Problems, Volume 7 - Conference Proceedings of the Society for Experimental Mechanics Series ◽

10.1007/978-3-319-95074-7_10 ◽

2018 ◽

pp. 51-56

Author(s):

Abdelmonem Lachhab ◽

Eric Robin ◽

Jean-Benoît Le Cam ◽

Frédéric Mortier ◽

Yvon Tirel ◽

...

Keyword(s):

Mechanical Response

Download Full-text

Comparison of Substructures Between Uniaxial and Biaxial Deformation in 1100-0 Aluminum

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100096989 ◽

1981 ◽

Vol 39 ◽

pp. 52-53

Author(s):

D. L. Rohr ◽

S. S. Hecker

Keyword(s):

Plastic Strain ◽

Cell Walls ◽

Room Temperature ◽

Mechanical Response ◽

Biaxial Tension ◽

Initial Deformation ◽

Uniaxial Deformation ◽

Biaxial Deformation ◽

Stress States ◽

Comprehensive Study

As part of a comprehensive study of microstructural and mechanical response of metals to uniaxial and biaxial deformations, the development of substructure in 1100 A1 has been studied over a range of plastic strain for two stress states.Specimens of 1100 aluminum annealed at 350 C were tested in uniaxial (UT) and balanced biaxial tension (BBT) at room temperature to different strain levels. The biaxial specimens were produced by the in-plane punch stretching technique. Areas of known strain levels were prepared for TEM by lapping followed by jet electropolishing. All specimens were examined in a JEOL 200B run at 150 and 200 kV within 24 to 36 hours after testing.The development of the substructure with deformation is shown in Fig. 1 for both stress states. Initial deformation produces dislocation tangles, which form cell walls by 10% uniaxial deformation, and start to recover to form subgrains by 25%. The results of several hundred measurements of cell/subgrain sizes by a linear intercept technique are presented in Table I.

Download Full-text

Construction of plastic contact deformation maps on ceramics: a case study on aluminum nitride

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100165641 ◽

1996 ◽

Vol 54 ◽

pp. 636-637

Author(s):

D. L. Callahan

Keyword(s):

Plastic Deformation ◽

Aluminum Nitride ◽

Mechanical Response ◽

Three Dimensional ◽

Bright Field Image ◽

Perfectly Plastic ◽

Contrast Analysis ◽

Deformation Patterns

Modern polishing, precision machining and microindentation techniques allow the processing and mechanical characterization of ceramics at nanometric scales and within entirely plastic deformation regimes. The mechanical response of most ceramics to such highly constrained contact is not predictable from macroscopic properties and the microstructural deformation patterns have proven difficult to characterize by the application of any individual technique. In this study, TEM techniques of contrast analysis and CBED are combined with stereographic analysis to construct a three-dimensional microstructure deformation map of the surface of a perfectly plastic microindentation on macroscopically brittle aluminum nitride.The bright field image in Figure 1 shows a lg Vickers microindentation contained within a single AlN grain far from any boundaries. High densities of dislocations are evident, particularly near facet edges but are not individually resolvable. The prominent bend contours also indicate the severity of plastic deformation. Figure 2 is a selected area diffraction pattern covering the entire indentation area.

Download Full-text