An Experimental Element Technique for Transverse Fracture in CFRP and GFRP

1992 ◽  
pp. 165-178
Author(s):  
Piet W. M. Peters
Keyword(s):  
Transverse Fracture ◽  
Element Technique

Boundary control design based on partial differential equation observer for vibration suppression and attitude control of flexible satellites with multi-section solar panels

2021 ◽  
pp. 107754632199015
Author(s):  
Mohammad Mahdi Ataei ◽  
Hassan Salarieh ◽  
Hossein Nejat Pishkenari ◽  
Hadi Jalili
Keyword(s):  
Differential Equation ◽  
Partial Differential Equation ◽  
Attitude Control ◽  
Vibration Suppression ◽  
Equation System ◽  
Solar Panels ◽  
Attitude Dynamics ◽  
Partial Differential ◽  
Satellite Attitude ◽  
Element Technique

A novel partial differential equation observer is proposed to be used in boundary attitude and vibration control of flexible satellites. Solar panels’ vibrations and attitude dynamics form a coupled partial differential equation–ordinary differential equation system which is controlled directly without discretization. Few feedback signals from boundaries are required which are estimated via a partial differential equation observer. Consequently, just satellite attitude and angular velocity should be measured and still the control system benefits information from continuous part vibrations. The closed-loop system is proved to be asymptotically stable. Simulations with a finite element technique illustrate good performance of this observer-based boundary controller.

Tissue necrosis and passage of fluid due to cold stress from the thermally damaged human body peripherals: A mathematical model

2015 ◽  
Vol 04 (02) ◽  
pp. 1550012
Author(s):  
M. A. Khanday ◽  
Fida Hussain ◽  
Khalid Nazir
Keyword(s):  
Mathematical Model ◽  
Finite Element ◽  
Heat Equation ◽  
Cold Stress ◽  
Human Body ◽  
Human Subjects ◽  
Diffusion Equations ◽  
Tissue Necrosis ◽  
Cold Temperatures ◽  
Element Technique

The development of cold injury takes place in the human subjects by means of crystallization of tissues in the exposed regions at severe cold temperatures. The process together with the evaluation of the passage of fluid discharge from the necrotic regions with respect to various degrees of frostbites has been carried out by using variational finite element technique. The model is based on the Pennes' bio-heat equation and mass diffusion equations together with suitable initial and boundary conditions. The results are analyzed in relation with atmospheric temperatures and other parameters of the tissue medium.

2-D electromagnetic modeling by finite‐element method with a dipole source and topography

Geophysics ◽  
2000 ◽  
Vol 65 (2) ◽  
pp. 465-475 ◽  
Author(s):  
Yuji Mitsuhata
Keyword(s):  
Finite Element ◽  
Delta Function ◽  
Dipole Source ◽  
Electromagnetic Modeling ◽  
Secondary Field ◽  
Controlled Source ◽  
Transient Electromagnetic ◽  
Isoparametric Finite Element ◽  
Anomalous Bodies ◽  
Element Technique

I present a method for calculating frequency‐domain electromagnetic responses caused by a dipole source over a 2-D structure. In modeling controlled‐source electromagnetic data, it is usual to separate the electromagnetic field into a primary (background) and a secondary (scattered) field to avoid a source singularity, and only the secondary field caused by anomalous bodies is computed numerically. However, this conventional scheme is not effective for complex structures lacking a simple background structure. The present modeling method uses a pseudo‐delta function to distribute the dipole source current, and does not need the separation of the primary and the secondary field. In addition, the method employs an isoparametric finite‐element technique to represent realistic topography. Numerical experiments are used to validate the code. Finally, a simulation of a source overprint effect and the response of topography for the long‐offset transient electromagnetic and the controlled‐source magnetotelluric measurements is presented.

Determination of Stress Concentration Around an Oblique Hole by a Finite-Element Technique

1983 ◽  
Vol 105 (2) ◽  
pp. 206-212 ◽  
Author(s):  
Hua-Ping Li ◽  
F. Ellyin
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Maximum Stress ◽  
Plate Thickness ◽  
Two Dimensional ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Parametric Studies ◽  
Element Technique

A plate weakened by an oblique penetration of a circular cylindrical hole has been investigated. The stress concentration around the hole is determined by a finite-element method. The results are compared with experimental data and other analytical works. Parametric studies of effects of angle of inclination, plate thickness, and width are performed. The maximum stress concentration factor (SCF) obtained from the finite-element analysis is higher than experimental results, and this deviation increases with the increase of angle of skewness. The major reason for this difference is attributed to the shear-action between layers parallel to the plate surface which cannot be directly included in the two-dimensional elements. An empirical formula is derived which accounts for the shear-action and renders the finite-element predictions in line with experimentally observed data.

Sign in / Sign up

Export Citation Format

Share Document