Peak Distributions and Peak Factors of Wind-Induced Pressure Processes on Tall Buildings

2016 ◽  
pp. 83-104
Author(s):  
Mingfeng Huang
Keyword(s):  
Tall Buildings

Tall Buildings: The Next Generation

2016 ◽  
Vol 106 (14) ◽  
pp. 16-23
Author(s):  
Antony WOOD
Keyword(s):  
Tall Buildings ◽  
Next Generation

Time-Dependent Bending Moment Analysis for Pile-Raft Foundation of Super Tall Buildings

2015 ◽  
Vol 105 (39) ◽  
pp. 1-8
Author(s):  
Shehong Liu ◽  
Juyun Yuan ◽  
Xin Zhao
Keyword(s):  
Tall Buildings ◽  
Bending Moment ◽  
Moment Analysis ◽  
Time Dependent ◽  
Raft Foundation

fib Bulletin 73. Tall Buildings

2014 ◽  
Author(s):  
Stephen Blundell ◽  
Alan Mann ◽  
Colin Banks ◽  
Jenny Burridge ◽  
Andy Truby ◽  
...  
Keyword(s):  
Tall Buildings

scholarly journals Parametric Analysis of the Shear Lag Effect in Tube Structural Systems of Tall Buildings

2020 ◽  
Vol 11 (1) ◽  
pp. 278
Author(s):  
Ivan Hafner ◽  
Anđelko Vlašić ◽  
Tomislav Kišiček ◽  
Tvrtko Renić
Keyword(s):  
Parametric Analysis ◽  
Numerical Models ◽  
Tall Buildings ◽  
Structural Systems ◽  
Structural Elements ◽  
Structural System ◽  
Shear Lag ◽  
Shear Lag Effect ◽  
Lag Effect ◽  
Secondary Structural Elements

Horizontal loads such as earthquake and wind are considered dominant loads for the design of tall buildings. One of the most efficient structural systems in this regard is the tube structural system. Even though such systems have a high resistance when it comes to horizontal loads, the shear lag effect that is characterized by an incomplete and uneven activation of vertical elements may cause a series of problems such as the deformation of internal panels and secondary structural elements, which cumulatively grow with the height of the building. In this paper, the shear lag effect in a typical tube structure will be observed and analyzed on a series of different numerical models. A parametric analysis will be conducted with a great number of variations in the structural elements and building layout, for the purpose of giving recommendations for an optimal design of a tube structural system.

A New Generation of Tools for the Design of Tall Buildings Subjected to Wind Loads

2008 ◽  
Author(s):  
Emil Simiu ◽  
Rene D. Gabbai
Keyword(s):  
Structural Engineering ◽  
Tall Buildings ◽  
Building Envelope ◽  
Force Balance ◽  
Wind Loads ◽  
Individual Member ◽  
Engineering Practice ◽  
Wind Effects ◽  
Uncertainty Estimates ◽  
Internal Forces

Current approaches to the estimation of wind-induced wind effects on tall buildings are based largely on 1970s and 1980s technology, and were shown to result in some cases in errors of up to 40%. Improvements are needed in: (i) the description of direction-dependent aerodynamics; (ii) the description of the direction-dependent extreme wind climate; (iii) the estimation of inertial wind effects induced by fluctuating aerodynamic forces acting on the entire building envelope; (iv) the estimation of uncertainties inherent in the wind effects; and (v) the use of applied wind forces, calculated inertial forces, and uncertainty estimates, to obtain via influence coefficients accurate and risk-consistent estimates of wind-induced internal forces or demand-to-capacity ratios for any individual structural member. Methods used in current wind engineering practice are especially deficient when the distribution of the wind loads over the building surface and their effects at levels other than the building base are not known, as is the case when measurements are obtained by the High-Frequency Force Balance method, particularly in the presence of aerodynamic interference effects due to neighboring buildings. The paper describes a procedure that makes it possible to estimate wind-induced internal forces and demand-to-capacity ratios in any individual member by: developing aerodynamic and wind climatological data sets, as well as aerodynamic/climatological directional interaction models; significantly improving the quality of the design via rigorous structural engineering methods made possible by modern computational resources; and properly accounting for knowledge uncertainties. The paper covers estimates of wind effects required for allowable stress design, wherein knowledge uncertainties pertaining to the parameters that determine the wind loading are not considered, as well as estimates required for strength design, in which these uncertainties need to be accounted for explicitly.

Sign in / Sign up

Export Citation Format

Share Document