A Sensor Integrated Solid-State Switch for Capacitor-Start Single-Phase Induction Motors in an IoT Ecosystem

Author(s):  
K. V. Gokul Lal ◽  
Unais Sait ◽  
Tarun Kumar
1995 ◽  
Vol 10 (1) ◽  
pp. 72-77 ◽  
Author(s):  
A.L. Julian ◽  
R.S. Wallace ◽  
P.K. Sood

2008 ◽  
Vol 368-372 ◽  
pp. 588-590 ◽  
Author(s):  
Ming Hao Fang ◽  
Jun Tong Huang ◽  
Zhao Hui Huang ◽  
Yan Gai Liu ◽  
Bin Jiang ◽  
...  

Single phase YIG powders were synthesized successfully using Fe2O3 and Y2O3 as starting materials by solid state reaction, and YIG ceramics were prepared by pressureless sintering. The influence of synthesizing temperature and Fe2O3 content on the final production were studied The effect of Fe2O3 content on volume density and microstructure of the sintered YIG was also investigated. The results showed that single phase YIG powders were synthesized by solid state reaction at 1400°C for 3h. When Fe2O3 content was excessive 3 wt%, YIG ceramics with a density of 5.294g·cm-3 was fabricated by sintering at 1480°C for 2.5h.


2014 ◽  
Vol 2 (38) ◽  
pp. 15829-15835 ◽  
Author(s):  
Kriti Tyagi ◽  
Bhasker Gahtori ◽  
Sivaiah Bathula ◽  
A. K. Srivastava ◽  
A. K. Shukla ◽  
...  

Intrinsically ultra-low thermal conductivity and electrical transport in single-phase Cu2SbSe3 synthesized employing a solid state reaction and spark plasma sintering.


2018 ◽  
Vol 54 (25) ◽  
pp. 3178-3181 ◽  
Author(s):  
Atsushi Inoishi ◽  
Akira Nishio ◽  
Yuto Yoshioka ◽  
Ayuko Kitajou ◽  
Shigeto Okada

We report a battery made from a single material using Li1.5Cr0.5Ti1.5(PO4)3 as the anode, cathode and electrolyte.


2012 ◽  
Vol 506 ◽  
pp. 57-60 ◽  
Author(s):  
M. Ebrahimi ◽  
Naruporn Monmaturapoj ◽  
S. Suttapreyasri ◽  
P. Pripatnanont

The biphasic calcium phosphate (BCP) concept was introduced to overcome disadvantages of single phase biomaterials. In this study, we prepared BCP from nanoHA and β-TCP that were synthesized via a solid state reaction. Three different ratios of pure BCP and collagen-based BCP scaffolds (%HA/%β-TCP; 30/70, 40/60 and 50/50) were produced using a polymeric sponge method. Physical and mechanical properties of all materials and scaffolds were investigated. XRD pattern proved the purity of each HA, β-TCP and BCP. SEM showed overall distribution of macropores (80-200 µm) with appropriate interconnected porosities. Total porosity of pure BCP (93% ± 2) was found to be higher than collagen-based BCP (85%± 3). It was observed that dimensional shrinkage of larger scaffold (39% ± 4) is lower than smaller one (42% ± 5) and scaffolds with higher HA (50%) ratio experienced greater shrinkage than those with higher β-TCP (70%) ratio (45% ±3 and 36% ±1 respectively). Mechanical properties of both groups tend to be very low and collagen coating had no influence on mechanical behavior. Further studies may improve the physical properties of these composite BCP.


Author(s):  
Rahul Santhosh ◽  
Sailakshmi ◽  
Vikram Siddharthan M ◽  
Sudha Yadav ◽  
Nithya M ◽  
...  

1996 ◽  
Vol 11 (2) ◽  
pp. 273-286 ◽  
Author(s):  
D. Lin ◽  
T. Batan ◽  
E.F. Fuchs ◽  
W.M. Grady

Sign in / Sign up

Export Citation Format

Share Document