Determination of stress intensity factors in plates near convex curvilinear cracks

1998 ◽  
Vol 34 (1) ◽  
pp. 125-127
Author(s):  
M. V. Lishchyns'ka
Keyword(s):  
Stress Intensity ◽  
Stress Intensity Factors ◽  
Intensity Factors ◽  
Curvilinear Cracks

DETERMINATION OF RESIDUAL STRESSES AND STRESS INTENSITY FACTORS BY REMOVING LOCAL MATERIAL

2017 ◽  
Vol 48 (4) ◽  
pp. 377-398
Author(s):  
Svyatoslav Igorevich Eleonskii ◽  
Igor Nikolaevich Odintsev ◽  
Vladimir Sergeevich Pisarev ◽  
Stanislav Mikhailovich Usov
Keyword(s):  
Stress Intensity ◽  
Residual Stresses ◽  
Stress Intensity Factors ◽  
Intensity Factors ◽  
Local Material

Experimental Determination of KI for Short Internal Cracks

2001 ◽  
Vol 68 (6) ◽  
pp. 937-943 ◽  
Author(s):  
K. Bearden ◽  
J. W. Dally ◽  
R. J. Sanford
Keyword(s):  
Stress Intensity ◽  
Stress Intensity Factors ◽  
Edge Crack ◽  
Series Solution ◽  
Experimental Studies ◽  
Experimental Methods ◽  
Internal Crack ◽  
Intensity Factors ◽  
Mode Stress

Since the pioneering discussion by Irwin, a significant effort has been devoted to determining stress intensity factors (K) using experimental methods. Techniques have been developed to determine stress intensity factors from photoelastic, strain gage, caustics, and moire´ data. All of these methods apply to a relatively long single-ended-edge crack. To date, the determination of K for internal cracks that are double-ended by experimental methods has not been addressed. This paper describes a photoelastic study of tension panels with both central and eccentric internal cracks. The data recorded in the experiments was analyzed using a new series solution for the opening-mode stress intensity factor for an internal crack. The data was also analyzed using the edge-crack series solution, which is currently employed in experimental studies. Results indicated that the experimental methods usually provided results accurate to within three to five percent if the series solution for the internal crack was employed in an overdeterministic numerical analysis of the data. Comparison of experimental results using the new series for the internal crack and the series for an edge crack showed the superiority of the new series.

Experimental Determination of Side Boundary Effects on Stress Intensity Factors in Surface Flaws

1975 ◽  
Vol 97 (1) ◽  
pp. 45-51 ◽  
Author(s):  
M. Jolles ◽  
J. J. McGowan ◽  
C. W. Smith
Keyword(s):  
Stress Intensity ◽  
Crack Length ◽  
Taylor Series ◽  
Stress Intensity Factors ◽  
Taylor Series Expansion ◽  
Correction Method ◽  
Intensity Factors ◽  
Surface Flaws ◽  
Plate Width

A technique consisting of stress-freezing photoelasticity coupled with a Taylor Series Expansion of the maximum local in-plane shearing stress known as the Taylor Series Correction Method (TSCM) is applied to the determination of stress intensity factors (SIF’s) in flat bottomed surface flaws of flaw depth/length ratios of approximately 0.033. Flaw depth/thickness ratios of approximately 0.20 and 0.40 were studied as were plate width/crack length ratios of approximately 2.33 and 1.25, the former of which corresponded to a nearly infinite width. Agreement to well within 10 percent was found with the Rice-Levy and Newman theories using a depth-modified secant correction and equivalent flaw depth/length ratios. The Shah-Kobayashi Theory, when compared on the same basis, was lower than the experimental results. Using a modified net section stress correction suggested by Shah, agreement with the Shah-Kobayashi Theory was greatly improved but agreement with the other theories was poorer. On the basis of the experiments alone, it was found that the SIF was intensified by about 10 percent by decreasing the plate width/crack length from 2.33 to 1.25.

scholarly journals Determination of mode I stress intensity factors of complex configurations using strain gages

2008 ◽  
Vol 3 (7) ◽  
pp. 1239-1255 ◽  
Author(s):  
Sanda Swamy ◽  
Manda Srikanth ◽  
Kondepudi Murthy ◽  
Puthuveettin Robi
Keyword(s):  
Stress Intensity ◽  
Stress Intensity Factors ◽  
Mode I ◽  
Strain Gages ◽  
Intensity Factors
Sign in / Sign up

Export Citation Format

Share Document