Development of a photomicroscope method for in situ damage monitoring under ultrasonic fatigue test

PurposeMechanical issues related to the information and growth of small cracks are considered to play a major role in very high cycle fatigue (VHCF) for metallic materials. Further efforts on better understanding in early stage of a crack are beneficial to estimating and preventing catastrophic damage for a long period service.Design/methodology/approachDependent on the ultrasonic loading system, a novel method of in situ photomicroscope is established to study the crack behaviors in VHCF regime.FindingsThis in situ photomicroscope method provides advantages in combination with fatigue damage monitoring at high magnification, a large number of cycles, and efficiency. Visional investigation with attached image proceeding code proves that the method has high resolution on both size and time, which permits reliable accuracy on small crack growth rate. It is observed that the crack propagation trends slower in the overall small crack stage down to the level of 10–11 m/cycle. Strain analysis relays on a real-time recording which is applied by using digital image correlation. Infrared camera recording indicates the method is also suitable for thermodynamic study while growth of damage.Originality/valueBenefiting from this method, it is more convenient and efficient to study the short crack propagation in VHCF regime.

Very High Cycle Fatigue Investigations on the Fatigue Strength of Additive Manufactured and Conventionally Wrought Inconel 718 at 873 K

The fatigue lives of additively manufactured (AM) Inconel 718 (IN718) produced by selective electron beam melting and conventional wrought material as reference conditions were studied in the very high cycle fatigue regime under fully reversed loading (R = −1) at the elevated temperature of 873 K using an ultrasonic fatigue testing system. The fatigue lives of the AM material were significantly reduced compared to the wrought material, which is discussed in relation to the microstructure and a fractographical analysis. The additively manufactured material showed large columnar grains with a favoured orientation to the building direction and porosity, whereas the wrought material showed a fine-grained structure with no significant texture, but had Nb- and Ti-rich non-metallic inclusions. Crystallographic crack initiation as well as crack initiation from the surface or internal defects were observed for the AM and the wrought IN718, respectively.

Internal Crack Initiation and Growth Starting from Artificially Generated Defects in Additively Manufactured Ti6Al4V Specimen in the VHCF Regime

The aim of the present work was to investigate the ‘fine granular area’ (FGA) formation based on artificially generated internal defects in additively manufactured Ti6Al4V specimens in the early stage of fatigue crack growth in the ‘very high cycle fatigue’ (VHCF) regime. Fatigue tests were performed with constant amplitude at pure tension-compression loading (R = −1) using an ultrasonic fatigue testing setup. Failed specimens were investigated using optical microscopy, high-resolution ‘scanning electron microscopy’ (SEM), and ‘focused ion beam’ (FIB) techniques. Further, the paper introduces alternative proposals to identify the FGA layer beneath the fracture surfaces in terms of the ‘cross section polishing’ (CSP) technique and metallic grindings with special attention paid to the crack origin, the surrounding microstructure, and the expansion of the nanograin layer beneath the fracture surface. Different existing fracture mechanical approaches were applied to evaluate if an FGA formation is possible. Moreover, the results were discussed in comparison to the experimental findings.

Giga-Cycle Fatigue Behavior of the Nuclear Structure of 316L Weldments

Some components made of 316L stainless steel in nuclear reactors are connected by welding, and these are under giga-cycle fatigue loading. Therefore, the giga-cycle fatigue behavior of 316L weldments, which are fabricated by Laser Beam Welding (LBW) and Gas Tungsten Arc Welding (GTAW), were investigated using an ultrasonic fatigue testing system. The results indicate that the fatigue strength of LBW-made weldments is almost the same as that of GTAW-made weldments even though the microstructure and mechanical properties of the weldments are different. For the LBW-made specimens, the LBW-induced internal pores with a diameter range of about 89–270 μm were observed in the fracture surface. However, an obvious decrease in fatigue life was not observed in such cases. For the GTAW-made specimens, the quality requirement of the weld seam has to be more strict to prevent fatigue strength from decreasing. The fatigue failure mode of the GTAW-made specimens is the same as that of LBW-made specimens in the high-cycle fatigue regime but different in the giga-cycle fatigue regime.