The critical velocity of mode-I fracture in a non-linear lattice in the absence of viscosity

2010 ◽  
Vol 22 (6-8) ◽  
pp. 505-514 ◽  
Author(s):  
Shay I. Heizler ◽  
David A. Kessler
Keyword(s):  
Critical Velocity ◽  
Mode I ◽  
Linear Lattice ◽  
Mode I Fracture ◽  
Non Linear

A novel Mode I fracture test for stitched composite laminates

2000 ◽  
Author(s):  
Leishan Chen ◽  
Peter Ifju ◽  
Bhavani Sankar
Keyword(s):  
Composite Laminates ◽  
Mode I ◽  
Fracture Test ◽  
Mode I Fracture

scholarly journals Effect of Testing Method Type and Specimen Size on Mode I Fracture Toughness of Kimachi Sandstone

2019 ◽  
Vol 135 (5) ◽  
pp. 33-41 ◽  
Author(s):  
Minami KATAOKA ◽  
Yuzo OBARA ◽  
Leona VAVRO ◽  
Kamil SOUCEK ◽  
Sang-Ho CHO ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Specimen Size ◽  
Mode I ◽  
Mode I Fracture ◽  
Mode I Fracture Toughness ◽  
Testing Method

Influence of specimen geometry on mode I fracture toughness of asphalt concrete

2021 ◽  
Vol 276 ◽  
pp. 122181
Author(s):  
Si Fuan ◽  
Ma Ke ◽  
Liu Kanghe ◽  
Li Kun ◽  
M.R.M. Aliha
Keyword(s):  
Fracture Toughness ◽  
Asphalt Concrete ◽  
Specimen Geometry ◽  
Mode I ◽  
Mode I Fracture ◽  
Mode I Fracture Toughness

A Study on Governing Parameters to Improve the Results of Caustic Applied to Mode-I Fracture Mechanics Problems

1994 ◽  
Vol 23 (1) ◽  
pp. 1-11 ◽  
Author(s):  
P. Rathinam ◽  
R. Narayanan ◽  
G. Jayarama Rao
Keyword(s):  
Fracture Mechanics ◽  
Mode I ◽  
Mode I Fracture

scholarly journals Comparative study of elastic properties and mode I fracture energy of carbon nanotube/epoxy and carbon fibre/epoxy laminated composites

2020 ◽  
Vol 8 (1) ◽  
Author(s):  
Jyotikalpa Bora ◽  
Sushen Kirtania
Keyword(s):  
Carbon Nanotube ◽  
Carbon Fibre ◽  
Fracture Energy ◽  
Elastic Properties ◽  
Volume Fraction ◽  
Laminated Composites ◽  
Laminated Composite ◽  
Fe Analysis ◽  
Mode I ◽  
Mode I Fracture

Abstract A comparative study of elastic properties and mode I fracture energy has been presented between conventional carbon fibre (CF)/epoxy and advanced carbon nanotube (CNT)/epoxy laminated composite materials. The volume fraction of CNT fibres has been considered as 15%, 30%, and 60% whereas; the volume fraction of CF has been kept constant at 60%. Three stacking sequences of the laminates viz.[0/0/0/0], [0/90/0/90] and [0/30/–30/90] have been considered in the present analysis. Periodic microstructure model has been used to calculate the elastic properties of the laminated composites. It has been observed analytically that the addition of only 15% CNT in epoxy will give almost the same value of longitudinal Young’s modulus as compared to the addition of 60% CF in epoxy. Finite element (FE) analysis of double cantilever beam specimens made from laminated composite has also been performed. It has been observed from FE analysis that the addition of 15% CNT in epoxy will also give almost the same value of mode I fracture energy as compared to the addition of 60% CF in epoxy. The value of mode I fracture energy for [0/0/0/0] laminated composite is two times higher than the other two types of laminated composites.

scholarly journals Analytical corrections for double-cantilever beam tests

2021 ◽  
Author(s):  
T. Chen ◽  
C. M. Harvey ◽  
S. Wang ◽  
V. V. Silberschmidt
Keyword(s):  
Elastic Foundation ◽  
Analytical Solutions ◽  
Data Reduction ◽  
Crack Tip ◽  
Beam Theory ◽  
Dynamic Loads ◽  
Structural Vibration ◽  
Mode I ◽  
Mode I Fracture ◽  
Reduction Methods

AbstractDouble-cantilever beams (DCBs) are widely used to study mode-I fracture behavior and to measure mode-I fracture toughness under quasi-static loads. Recently, the authors have developed analytical solutions for DCBs under dynamic loads with consideration of structural vibration and wave propagation. There are two methods of beam-theory-based data reduction to determine the energy release rate: (i) using an effective built-in boundary condition at the crack tip, and (ii) employing an elastic foundation to model the uncracked interface of the DCB. In this letter, analytical corrections for a crack-tip rotation of DCBs under quasi-static and dynamic loads are presented, afforded by combining both these data-reduction methods and the authors’ recent analytical solutions for each. Convenient and easy-to-use analytical corrections for DCB tests are obtained, which avoid the complexity and difficulty of the elastic foundation approach, and the need for multiple experimental measurements of DCB compliance and crack length. The corrections are, to the best of the authors’ knowledge, completely new. Verification cases based on numerical simulation are presented to demonstrate the utility of the corrections.

scholarly journals The effect of modified tannic acid (TA) eco-epoxy adhesives on mode I fracture toughness of bonded joints

2021 ◽  
Vol 96 ◽  
pp. 107122
Author(s):  
Mohamed Nasr Saleh ◽  
Nataša Z. Tomić ◽  
Aleksandar Marinković ◽  
Sofia Teixeira de Freitas
Keyword(s):  
Fracture Toughness ◽  
Tannic Acid ◽  
Mode I ◽  
Bonded Joints ◽  
Mode I Fracture ◽  
Mode I Fracture Toughness ◽  
Epoxy Adhesives

A fracture mechanics model to predict the rate sensitivity of mode I fracture of concrete

1987 ◽  
Vol 17 (2) ◽  
pp. 249-262 ◽  
Author(s):  
Reji John ◽  
Surendra P. Shah ◽  
Yeou-Shang Jeng
Keyword(s):  
Fracture Mechanics ◽  
Rate Sensitivity ◽  
Mode I ◽  
Mode I Fracture ◽  
Mechanics Model
Sign in / Sign up

Export Citation Format

Share Document