The first critical heat-flux density of kerosene in stepwise and steady-state releases of heat

2006 ◽  
Vol 79 (6) ◽  
pp. 1106-1109
Author(s):  
D. S. Obukhov
Keyword(s):  
Heat Flux ◽  
Steady State ◽  
Flux Density ◽  
Critical Heat Flux ◽  
Heat Flux Density

Influence of characteristics of porous coatings on first critical heat-flux density in boiling

1988 ◽  
Vol 64 (4) ◽  
pp. 364-365
Author(s):  
A. A. Shapoval ◽  
V. K. Zaripov ◽  
M. G. Semena
Keyword(s):  
Heat Flux ◽  
Flux Density ◽  
Critical Heat Flux ◽  
Heat Flux Density ◽  
Porous Coatings

Critical heat-flux density in open channels cooled by helium II

1982 ◽  
Vol 42 (2) ◽  
pp. 140-143
Author(s):  
V. G. Pron'ko ◽  
V. V. Gorokhov ◽  
V. N. Saverin
Keyword(s):  
Heat Flux ◽  
Flux Density ◽  
Critical Heat Flux ◽  
Heat Flux Density ◽  
Open Channels ◽  
Helium Ii

scholarly journals Critical heat flux density in diphasic thermosyphons

2017 ◽  
Vol 110 ◽  
pp. 01064 ◽  
Author(s):  
Konstantin O. Ponomarev ◽  
Evgeniya G. Orlova ◽  
Аtlant E. Nurpeiis
Keyword(s):  
Heat Flux ◽  
Flux Density ◽  
Critical Heat Flux ◽  
Heat Flux Density

THERMAL BEHAVIOR AND IGNITION OF HIGH-ENERGY MATERIALS CONTAINING B, ALB2, AND TIB2

2020 ◽  
Author(s):  
A. G. Korotkikh ◽  
◽  
V. A. Arkhipov ◽  
I. V. Sorokin ◽  
E. A. Selikhova ◽  
...  
Keyword(s):  
Heat Flux ◽  
Thermal Behavior ◽  
Flux Density ◽  
Ignition Delay ◽  
Delay Time ◽  
Heat Flux Density ◽  
Ignition Delay Time ◽  
High Energy ◽  
Energy Materials ◽  
High Energy Materials

The paper presents the results of ignition and thermal behavior for samples of high-energy materials (HEM) based on ammonium perchlorate (AP) and ammonium nitrate (AN), active binder and powders of Al, B, AlB2, and TiB2. A CO2 laser with a heat flux density range of 90-200 W/cm2 was used for studies of ignition. The activation energy and characteristics of ignition for the HEM samples were determined. Also, the ignition delay time and the surface temperature of the reaction layer during the heating and ignition for the HEM samples were determined. It was found that the complete replacement of micron-sized aluminum powder by amorphous boron in a HEM sample leads to a considerable decrease in the ignition delay time by a factor of 2.2-2.8 at the same heat flux density due to high chemical activity and the difference in the oxidation mechanisms of boron particles. The use of aluminum diboride in a HEM sample allows one to reduce the ignition delay time of a HEM sample by a factor of 1.7-2.2. The quasi-stationary ignition temperature is the same for the AlB2-based and AlB12-based HEM samples.

A thermoelectric device for ophthalmic heat flux density measurements: results of piloting in healthy individuals

2019 ◽  
Vol 80 (3) ◽  
pp. 45-51
Author(s):  
L. Anatychuk ◽  
N. Pasyechnikova ◽  
V. Naumenko ◽  
O. Zadorozhnyy ◽  
R. Kobylianskyi ◽  
...  
Keyword(s):  
Heat Flux ◽  
Flux Density ◽  
Heat Flux Density ◽  
Thermoelectric Device ◽  
Healthy Individuals ◽  
Density Measurements
Sign in / Sign up

Export Citation Format

Share Document