Wear Study of Mechanical Clinching Dies During Joining of Advanced High-Strength Steel Sheets

2017 ◽  
Vol 49 (5) ◽  
pp. 726-737 ◽  
Author(s):  
L. Kaščák ◽  
J. Mucha ◽  
E. Spišák ◽  
R. Kubík
Keyword(s):  
High Strength Steel ◽  
High Strength ◽  
Advanced High Strength Steel ◽  
Steel Sheets ◽  
Mechanical Clinching

scholarly journals Mechanical clinching and self-pierce riveting for sheet combination of 780-MPa high-strength steel and aluminium alloy A5052 sheets and durability on salt spray test of joints

2021 ◽  
Vol 113 (1-2) ◽  
pp. 59-72
Author(s):  
Yohei Abe ◽  
Ken-ichiro Mori
Keyword(s):  
Aluminium Alloy ◽  
High Strength Steel ◽  
Salt Spray ◽  
High Strength ◽  
Alloy Sheet ◽  
Galvanized Steel ◽  
Load Reduction ◽  
Minimum Thickness ◽  
Steel Sheets ◽  
Mechanical Clinching

AbstractTo increase the usage of high-strength steel and aluminium alloy sheets for lightweight automobile body panels, the joinability of sheet combinations including a 780-MPa high-strength steel and an aluminium alloy A5052 sheets by mechanical clinching and self-pierce riveting was investigated for different tool shapes in an experiment. All the sheet combinations except for the two steel sheets by self-pierce riveting, i.e., the two steel sheets, the two aluminium alloy sheets, and the steel-aluminium alloy sheets, were successfully joined by both the joining methods without the gaps among the rivet and the sheets. Then, to show the durability of the joined sheets, the corrosion behaviour and the joint strength of the aged sheets by a salt spray test were measured. The corrosion and the load reduction of the clinched and the riveted two aluminium alloy sheets were little. The corrosion of the clinched two steel sheets without the galvanized layer progressed, and then the load after 1176 h decreased by 85%. In the clinched two galvanized steel sheets, the corrosion progress slowed down by 24%. In the clinched steel and aluminium alloy sheets, the thickness reduction occurred near the minimum thickness of the upper sheet and in the upper surface on the edge of the lower aluminium alloy sheet, whereas the top surface of the upper sheet and the upper surface of the lower sheet were mainly corroded in the riveted joint. The load reduction was caused by the two thickness reductions, i.e., the reduction in the minimum thickness of the upper sheet and the reduction in the flange of the aluminium alloy sheet. Although the load of the clinched steel without the galvanized coating layer and aluminium alloy sheets decreased by about 20%, the use of the galvanized steel sheet brought the decrease by about 11%. It was found that the use of the galvanized steel sheets is effective for the decrease of strength reduction due to corrosion.

scholarly journals Integration process of stamping and welding for DP600 advanced high strength steel sheets

2018 ◽  
Vol 15 ◽  
pp. 684-692
Author(s):  
Baowei Ma ◽  
Dean Meng ◽  
Xi Gu ◽  
Xu Ma ◽  
Dawei Zhang ◽  
...  
Keyword(s):  
High Strength Steel ◽  
High Strength ◽  
Advanced High Strength Steel ◽  
Integration Process ◽  
Steel Sheets

Formability Analysis of Diode-Laser-Welded Tailored Blanks of Advanced High-Strength Steel Sheets

2009 ◽  
Vol 40 (8) ◽  
pp. 1955-1967 ◽  
Author(s):  
S.K. Panda ◽  
V.H. Baltazar Hernandez ◽  
M.L. Kuntz ◽  
Y. Zhou
Keyword(s):  
Diode Laser ◽  
High Strength Steel ◽  
High Strength ◽  
Advanced High Strength Steel ◽  
Steel Sheets ◽  
Tailored Blanks

Application of Gotoh's Orthotropic Yield Function for Modeling Advanced High-Strength Steel Sheets

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Wei Tong
Keyword(s):  
High Strength Steel ◽  
Biaxial Tension ◽  
High Strength ◽  
Yield Function ◽  
Uniaxial Tensile ◽  
Plasticity Model ◽  
Advanced High Strength Steel ◽  
Directional Dependence ◽  
Steel Sheets ◽  
Tension Loading

An accurate description of the directional dependence of uniaxial tensile yielding and plastic flow in advanced high-strength steel sheets may require either a nonassociated plasticity model with separate quadratic yield function and flow potential or an associated plasticity model with nonquadratic yield function. In this paper, Gotoh's fourth-order homogeneous polynomial yield function is applied to model two advanced high-strength steel sheets in an associated plasticity model. Both the parameter selection for calibrating Gotoh's yield function and its positivity and convexity verification are given in some detail. Similarities and differences between the associated plasticity model presented here and the nonassociated one appeared in the literature are discussed in terms of the directional dependence of yield stresses and plastic strain ratios under uniaxial tension and yield stresses under biaxial tension loading.

Sign in / Sign up

Export Citation Format

Share Document