Wave Extraction and Attenuation Performance of An Edinburgh Duck Wave Energy Converter

2021 ◽  
Vol 35 (6) ◽  
pp. 905-913
Author(s):  
Bin-zhen Zhou ◽  
Jia-hui Li ◽  
Heng-ming Zhang ◽  
Li-fen Chen ◽  
Lei Wang ◽  
...  
Keyword(s):  
Wave Energy ◽  
Wave Energy Converter ◽  
Energy Converter

Design and optimization investigation on hydraulic transmission and energy storage system for a floating-array-buoys wave energy converter

2021 ◽  
Vol 235 ◽  
pp. 113998
Author(s):  
Pengyuan Sun ◽  
Qiang Li ◽  
Hongzhou He ◽  
Hu Chen ◽  
Jun Zhang ◽  
...  
Keyword(s):  
Energy Storage ◽  
Wave Energy ◽  
Storage System ◽  
Energy Storage System ◽  
Wave Energy Converter ◽  
Energy Converter ◽  
Design And Optimization

Hydrodynamic analysis of a novel wave energy converter: Hull Reservoir Wave Energy Converter (HRWEC)

2021 ◽  
Vol 170 ◽  
pp. 1020-1039
Author(s):  
S.D.G.S.P. Gunawardane ◽  
G.A.C.T. Bandara ◽  
Young-Ho Lee
Keyword(s):  
Wave Energy ◽  
Wave Energy Converter ◽  
Energy Converter ◽  
Hydrodynamic Analysis

On the power performance of a wave energy converter with a direct mechanical drive power take-off system controlled by latching

2021 ◽  
Author(s):  
Milad Shadman ◽  
Gustavo Omar Guarniz Avalos ◽  
Segen F. Estefen
Keyword(s):  
Wave Energy ◽  
Wave Energy Converter ◽  
Power Performance ◽  
Energy Converter ◽  
Drive Power

scholarly journals A Piezoelectric Wave-Energy Converter Equipped with a Geared-Linkage-Based Frequency Up-Conversion Mechanism

Sensors ◽  
2020 ◽  
Vol 21 (1) ◽  
pp. 204
Author(s):  
Shao-En Chen ◽  
Ray-Yeng Yang ◽  
Guang-Kai Wu ◽  
Chia-Che Wu
Keyword(s):  
Power Generation ◽  
Wave Energy ◽  
Wave Motion ◽  
Wave Energy Converter ◽  
Gear Train ◽  
Piezoelectric Composite ◽  
Maximum Height ◽  
Resistive Load ◽  
Linkage Mechanism ◽  
Energy Converter

In this paper, a piezoelectric wave-energy converter (PWEC), consisting of a buoy, a frequency up-conversion mechanism, and a piezoelectric power-generator component, is developed. The frequency up-conversion mechanism consists of a gear train and geared-linkage mechanism, which converted lower frequencies of wave motion into higher frequencies of mechanical motion. The slider had a six-period displacement compared to the wave motion and was used to excite the piezoelectric power-generation component. Therefore, the operating frequency of the piezoelectric power-generation component was six times the frequency of the wave motion. The developed, flexible piezoelectric composite films of the generator component were used to generate electrical voltage. The piezoelectric film was composed of a copper/nickel foil as the substrate, lead–zirconium–titanium (PZT) material as the piezoelectric layer, and silver material as an upper-electrode layer. The sol-gel process was used to fabricate the PZT layer. The developed PWEC was tested in the wave flume at the Tainan Hydraulics Laboratory, Taiwan (THL). The maximum height and the minimum period were set to 100 mm and 1 s, respectively. The maximum voltage of the measured value was 2.8 V. The root-mean-square (RMS) voltage was 824 mV, which was measured through connection to an external 495 kΩ resistive load. The average electric power was 1.37 μW.

scholarly journals Passive Model Predictive Control on a Two-Body Self-Referenced Point Absorber Wave Energy Converter

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1731
Author(s):  
Dan Montoya ◽  
Elisabetta Tedeschi ◽  
Luca Castellini ◽  
Tiago Martins
Keyword(s):  
Model Predictive Control ◽  
Predictive Control ◽  
Wave Energy ◽  
Power Flow ◽  
Linear Constraints ◽  
Wave Energy Converter ◽  
Control Technique ◽  
Computational Time ◽  
Energy Converter ◽  
Point Absorber

Wave energy is nowadays one of the most promising renewable energy sources; however, wave energy technology has not reached the fully-commercial stage, yet. One key aspect to achieve this goal is to identify an effective control strategy for each selected Wave Energy Converter (WEC), in order to extract the maximum energy from the waves, while respecting the physical constraints of the device. Model Predictive Control (MPC) can inherently satisfy these requirements. Generally, MPC is formulated as a quadratic programming problem with linear constraints (e.g., on position, speed and Power Take-Off (PTO) force). Since, in the most general case, this control technique requires bidirectional power flow between the PTO system and the grid, it has similar characteristics as reactive control. This means that, under some operating conditions, the energy losses may be equivalent, or even larger, than the energy yielded. As many WECs are designed to only allow unidirectional power flow, it is necessary to set nonlinear constraints. This makes the optimization problem significantly more expensive in terms of computational time. This work proposes two MPC control strategies applied to a two-body point absorber that address this issue from two different perspectives: (a) adapting the MPC formulation to passive loading strategy; and (b) adapting linear constraints in the MPC in order to only allow an unidirectional power flow. The results show that the two alternative proposals have similar performance in terms of computational time compared to the regular MPC and obtain considerably more power than the linear passive control, thus proving to be a good option for unidirectional PTO systems.

Irregular wave interaction with an offshore OWC wave energy converter

2021 ◽  
Vol 222 ◽  
pp. 108619
Author(s):  
Milad Zabihi ◽  
Said Mazaheri ◽  
Masoud Montazeri Namin ◽  
Ahmad Rezaee Mazyak
Keyword(s):  
Wave Energy ◽  
Wave Interaction ◽  
Wave Energy Converter ◽  
Energy Converter ◽  
Irregular Wave
Sign in / Sign up

Export Citation Format

Share Document