Laser Cladding of Stellite-6 on AISI 316 L Austenitic Stainless Steel: Empirical-Statistical Modeling and Parameter Optimization

2020 ◽  
Author(s):  
Jeferson Trevizan Pacheco ◽  
Leandro João da Silva ◽  
Luiz Delagnelo Barbetta ◽  
Henrique Santos Ferreira ◽  
Marcelo Taveira Veiga ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Statistical Modeling ◽  
Laser Cladding ◽  
Parameter Optimization ◽  
Stellite 6 ◽  
Aisi 316 ◽  
Aisi 316 L

Tribological behavior of PIII treated AISI 316 L austenitic stainless steel against UHMWPE counterface

Wear ◽  
2006 ◽  
Vol 261 (3-4) ◽  
pp. 264-268 ◽  
Author(s):  
N. Saklakoğlu ◽  
İ.E. Saklakoğlu ◽  
K.T. Short ◽  
G.A. Collins
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Tribological Behavior ◽  
Aisi 316 ◽  
Aisi 316 L

scholarly journals Wear Behaviour of Stellite 6 Coatings Produced on an Austenitic Stainless Steel Substrate by Laser Cladding Using Two Different Heat Inputs

2014 ◽  
Vol 619 ◽  
pp. 13-17 ◽  
Author(s):  
Alain Kusmoko ◽  
Druce P. Dunne ◽  
Hui Jun Li
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Laser Cladding ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Testing ◽  
Wear Behaviour ◽  
Chemical Compositions ◽  
Stellite 6

Stellite 6 was deposited by laser cladding on an austenitic stainless steel substrate (ASS) with energy inputs of 1 kW (ASS 1) and 1.8 kW (ASS 1.8). The chemical compositions and microstructures of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was assessed using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the austenitic stainless steel substrate with the lower heat input (ASS 1). Further, the Stellite coating for ASS 1 was significantly harder than that obtained for ASS 1.8. The wear test results showed that the weight loss for ASS 1 was much lower than for ASS 1.8. It is concluded that the lower hardness of the coating for ASS 1.8, together with the softer underlying substrate structure, markedly reduced the wear resistance of the Stellite 6 coating.

Laser cladding of Si on austenitic stainless steel

2005 ◽  
Vol 21 (2) ◽  
pp. 113-118 ◽  
Author(s):  
R. Jagdheesh ◽  
U. Kamachi Mudali ◽  
D. Sastikumar ◽  
A. K. Nath
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Laser Cladding
Sign in / Sign up

Export Citation Format

Share Document