scholarly journals Wear Behaviour of Stellite 6 Coatings Produced on an Austenitic Stainless Steel Substrate by Laser Cladding Using Two Different Heat Inputs

2014 ◽  
Vol 619 ◽  
pp. 13-17 ◽  
Author(s):  
Alain Kusmoko ◽  
Druce P. Dunne ◽  
Hui Jun Li
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Laser Cladding ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Testing ◽  
Wear Behaviour ◽  
Chemical Compositions ◽  
Stellite 6

Stellite 6 was deposited by laser cladding on an austenitic stainless steel substrate (ASS) with energy inputs of 1 kW (ASS 1) and 1.8 kW (ASS 1.8). The chemical compositions and microstructures of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was assessed using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the austenitic stainless steel substrate with the lower heat input (ASS 1). Further, the Stellite coating for ASS 1 was significantly harder than that obtained for ASS 1.8. The wear test results showed that the weight loss for ASS 1 was much lower than for ASS 1.8. It is concluded that the lower hardness of the coating for ASS 1.8, together with the softer underlying substrate structure, markedly reduced the wear resistance of the Stellite 6 coating.

Evaluation of Two Different Energy Inputs for Deposition of Stellite 6 by Laser Cladding on a Martensitic Stainless Steel Substrate

2015 ◽  
Vol 1119 ◽  
pp. 628-632
Author(s):  
Alain Kusmoko ◽  
Druce Dunne ◽  
Hui Jun Li
Keyword(s):  
Stainless Steel ◽  
Laser Cladding ◽  
Martensitic Stainless Steel ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Testing ◽  
Chemical Compositions ◽  
Stellite 6 ◽  
Energy Inputs

Stellite 6 was deposited by laser cladding on a martensitic stainless steel substrate with energy inputs of 1 kW (MSS-1) and 1.8 kW (MSS-1.8). The chemical compositions and microstructures of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was assessed using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the MSS steel substrate with the lower heat input (MSS-1). Further, the Stellite coating for MSS-1 was significantly harder than that obtained for MSS-1.8. The wear test results indicated that the weight loss for MSS-1 was much lower than for MSS-1.8. It is concluded that the lower hardness of the coating for MSS-1.8, markedly reduced the wear resistance of the Stellite 6 coating.

Dilution and C Content Estimation of Stellite 6 Fabricated on a 1050 Steel Substrate by Laser Cladding

2017 ◽  
Vol 263 ◽  
pp. 131-136
Author(s):  
Alain Kusmoko ◽  
Druce Dunne ◽  
Hui Jun Li
Keyword(s):  
Laser Cladding ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Test ◽  
Wear Testing ◽  
Chemical Compositions ◽  
Test Results ◽  
Stellite 6 ◽  
Service Conditions ◽  
Stellite Coating

Stellite 6 was fabricated by laser cladding on a 1050 steel (MS) substrate with laser powers of 1 kW (MS-1) and 1.8 kW (MS-1.8). The chemical compositions and microstructures of the coatings were analysed by X-Ray Fluoroscense, optical microscopy and scanning electron microscopy. The microhardness of the coatings was examined and the wear mechanism of the coatings was evaluated using a ball-on-plate wear testing machine. The results indicated less cracking and pore development for Stellite 6 coatings applied to the 1050 steel substrate with the lower laser power (MS-1). Moreover, the Stellite coating for MS-1 was significantly harder than that obtained for MS-1.8. The wear test results showed that the weight loss for MS-1 was much lower than for MS-1.8. The evaluations of dilution and calculation of carbon content indicated that MS-1 has lower dilution and higher coating C content than MS-1.8. It is concluded that the lower hardness of the coating for MS-1.8, substantially reduced the wear resistance of the Stellite 6 coating and the lower hardness of the coating for MS-1.8 was due to higher level of dilution and lower coating C content. The coating-substrate couple must be considered in assessing the likely performance of the coating under service conditions.

Laser Cladding of Wear Resistant Stellite 6 Coating on P22 Steel Substrate with Two Different Energy Inputs

2014 ◽  
Vol 911 ◽  
pp. 97-101 ◽  
Author(s):  
Alain Kusmoko ◽  
Druce Dunne ◽  
Hui Jun Li ◽  
David Nolan
Keyword(s):  
Laser Cladding ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Test ◽  
Wear Testing ◽  
Chemical Compositions ◽  
Stellite 6 ◽  
Energy Inputs ◽  
Stellite Coating ◽  
Spectroscopy Optical

Stellite 6 was deposited by laser cladding on a P22 steel substrate with energy inputs of 1 kW (P22-1) and 1.8 kW (P22-1.8). The chemical compositions and microstructures of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was examined using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the P22 steel substrate with the lower heat input (P22-1). Further, the Stellite coating for P22-1 was significantly harder than that obtained for P22-1.8. The wear test results showed that the weight loss for P22-1 was much lower than for P22-1.8. It is concluded that the lower hardness of the coating for P22-1.8, markedly reduced the wear resistance of the Stellite 6 coating.

Surface Morphology and Wear Analysis of Stellite 6 Deposited on 9Cr-1Mo Steel Substrate by Laser Cladding

2015 ◽  
Vol 1119 ◽  
pp. 640-644
Author(s):  
Alain Kusmoko ◽  
Hui Jun Li
Keyword(s):  
Laser Cladding ◽  
Steel Substrate ◽  
Testing Machine ◽  
Wear Test ◽  
Wear Testing ◽  
Chemical Compositions ◽  
Force Microscopy ◽  
Stellite 6 ◽  
Substrate Structure ◽  
Energy Inputs

Stellite 6 was deposited by laser cladding on a 9Cr-1Mo (P91) substrate with energy inputs of 1 kW (P91-1) and 1.8 kW (P91-1.8). The chemical compositions, microstructures and surface roughnesses of these coatings were characterized by atomic absorption spectroscopy, optical microscopy, scanning electron microscopy and atomic force microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was evaluated using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the 9Cr-1Mo (P91) steel substrate with the lower heat input (P91-1). Further, the Stellite coating for P91-1 was significantly harder than that obtained for P91-1.8. The wear test results indicated that the weight loss for P91-1 was much lower than for P91-1.8. The surface topography data indicated that the surface roughness for P91-1 was much lower than for P91-1.8. It is concluded that the lower hardness of the coating for P91-1.8, together with the softer underlying substrate structure, markedly reduced the wear resistance of the Stellite 6 coating.

Laser Cladding of Stainless Steel Substrates with Stellite 6

2013 ◽  
Vol 773-774 ◽  
pp. 573-589 ◽  
Author(s):  
Alain Kusmoko ◽  
D. Dunne ◽  
H. Li ◽  
D. Nolan
Keyword(s):  
Stainless Steel ◽  
Laser Cladding ◽  
Testing Machine ◽  
Austenitic Stainless Steels ◽  
Wear Test ◽  
Wear Testing ◽  
Test Results ◽  
Stellite 6 ◽  
Steel Substrates ◽  
Spectroscopy Optical

Stellite 6 coatings were produced using laser cladding of two different steel substrates (martensitic and austenitic stainless steels). The chemical composition and microstructure of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was examined using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the martensitic stainless steel (SS) substrate. The wear test results showed that the weight loss for the coating on martensitic SS was significantly lower than for the austenitic SS substrate. It is concluded that the higher hardness of the coating on the martensitic SS, together with the harder and more rigid substrate increase the wear resistance of the Stellite 6 coating.

Study of Laser Cladding of Stellite 6 on Nickel Superalloy Substrate with Two Different Energy Inputs

2014 ◽  
Vol 896 ◽  
pp. 600-604
Author(s):  
Alain Kusmoko ◽  
Druce Dunne ◽  
Hui Jun Li ◽  
David Nolan
Keyword(s):  
Laser Cladding ◽  
Testing Machine ◽  
Wear Test ◽  
Nickel Superalloy ◽  
Wear Testing ◽  
Chemical Compositions ◽  
Stellite 6 ◽  
Substrate Structure ◽  
Energy Inputs ◽  
Stellite Coating

Stellite 6 was deposited by laser cladding on a nickel superalloy substrate (NIS) with energy inputs of 1 kW (NIS 1) and 1.8 kW (NIS 1.8). The chemical compositions and microstructures of these coatings were characterized by atomic absorption spectroscopy, optical microscopy and scanning electron microscopy. The microhardness of the coatings was measured and the wear mechanism of the coatings was examined using a pin-on-plate (reciprocating) wear testing machine. The results showed less cracking and pore development for Stellite 6 coatings applied to the nickel superalloy substrate with the lower heat input (NIS 1). Further, the Stellite coating for NIS 1 was significantly harder than that obtained for NIS 1.8. The wear test results showed that the weight loss for NIS 1 was much lower than for NIS 1.8. It is concluded that the lower hardness of the coating for NIS 1.8, together with the softer underlying substrate structure, markedly reduced the wear resistance of the Stellite 6 coating.

scholarly journals Effects of WC Particle Types on the Microstructures and Properties of WC-Reinforced Ni60 Composite Coatings Produced by Laser Cladding

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 583 ◽  
Author(s):  
Pengxian Zhang ◽  
Yibin Pang ◽  
Mingwei Yu
Keyword(s):  
Stainless Steel ◽  
Uniform Distribution ◽  
Laser Cladding ◽  
Steel Surface ◽  
Stainless Steel Substrate ◽  
Steel Substrate ◽  
Composite Coatings ◽  
304 Stainless Steel ◽  
Stainless Steel Surface ◽  
Different Types

WC-reinforced Ni60 composite coatings with different types of WC particles were prepared on 304 stainless steel surface by laser cladding. The influences of spherical WC, shaped WC, and flocculent WC on the microstructures and properties of composite coatings were investigated. The results showed that three types of WC particles distribute differently in the cladding coatings, with spherical WC particles stacking at the bottom, shaped WC aggregating at middle and lower parts, with flocculent WC particles dispersing homogeneously. The hardnesses, wear resistances, corrosion resistances, and thermal shock resistances of the coatings are significantly improved compared with the stainless steel substrate, regardless of the type of WC that is added, and especially with regard to the microhardness of the cladding coating; the addition of spherical or shaped WC particles can be up to 2000 HV0.05 in some areas. Flocculent WC, shaped WC, and spherical WC demonstrate large to small improvements in that order. From the results mentioned above, the addition of flocculent WC can produce a cladding coating with a uniform distribution of WC that is of higher quality compared with those from spherical WC and shaped WC.

Sign in / Sign up

Export Citation Format

Share Document